This is the question with 3 subdivisions as per bartleby honor code. So please solve all • A DC motor with the below specifications is required to deliveran output power of 6 W to a load of 1700 g.Power FlowLOADMSpeedTorqueKt = 0.226 N.m/AKe = 0.00155 V/r.p.m.Ra = 4.4 QGerating Voltage = 5.9 VNotes:Your answers must be rounded to 2 decimal places.Usen as 3.14Use g = 9.81 m/s?Answer the below questions:1. The maximum power that can be delivered by the motor is2. The torque of the load is3. The angular speed at which the motor is rotating is

• A DC motor with the below specifications is required to deliver an output power of 6 W to a load of 1700 g. Power Flow LOAD Speed Torque Kt = 0.226 N.m/A Ke = 0.00155 V/r.p.m. Ra = 4,4 Q Gerating Voltage = 5.9 V %3D Notes: Your answers must be rounded to 2 decimal places. Usen as 3.14 Use g = 9.81 m/s? Answer the below questions: 1. The maximum power that can be delivered by the motor is 2. The torque of the load is 3. The angular speed at which the motor is rotating is

• A DC motor with the below specifications is required to deliver an output power of 6 W to a load of 1700 g. Power Flow LOAD Speed Torque Kt = 0.226 N.m/A Ke = 0.00155 V/r.p.m. Ra = 4,4 Q Gerating Voltage = 5.9 V %3D Notes: Your answers must be rounded to 2 decimal places. Usen as 3.14 Use g = 9.81 m/s? Answer the below questions: 1. The maximum power that can be delivered by the motor is 2. The torque of the load is 3. The angular speed at which the motor is rotating is

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter29: Dc Generators

Section: Chapter Questions

Problem 1PA: You are working as an electrician in a large steel manufacturing plant, and you are in the process...

See similar textbooks

Similar questions

You are working as an electrician in a large steel manufacturing plant, and you are in the process of doing preventive maintenance on a large DC generator. You have megged both the series and shunt field windings and found that each has over 10 M to ground. Your ohmmeter, however, indicates a resistance of 1.5 across terminals S1andS2. The ohmmeter indicates a resistance of 225 between terminals F1andF2. Are these readings normal for this type machine, or is there a likely problem? Explain your answer.
A steam turbine generator is designed to generate 5.5MW of electrical power at a 6300V, 50HZ and 0.95 lag. The steam turbine requires 28 tons per hour of a high-pressure steam of temperature and pressure of 4000C and 40 bar. The steam turbine is a condensing type. If the temperature of the exhaust steam is 400 C (a).Calculate the efficiency of the steam turbine (b)What are the three (3) major advantages and disadvantages of the steam turbine? (c )What are the methods of improving efficiency of the Brayton cycle?
A 5.44 hp (horse power) motor with a 0.6 lagging power factor is connected to a 208 V, 60 Hz supply. Knowing that 1hp=746 W, calculate with approximation how much reactive power (Q) the circuit might have? a. 5406 VAR b. 6757 VA c. 1400 VAR d. 6757 VAR e. 1400 VA f. 5406 VA
Q2: A 9-Hp motor with an efficiency of 90% and a 0.8 lagging power factor and A small industrial plant has a 10-kW heating load with 20 bulbs (40 W) are connected parallel to a 220-V, 50-Hz supply. Find a) the number of watts, volt-ampere reactive, volt-ampere and Fp for each branch. b) Total real power, total reactive power, total apparent power and power factor of the circuit. Draw triangle power. ¢) The current source.
An industrial assembly hall is continuously lightedby one hundred 40-W mercury vapor lamps suppliedby a 120-V and 60-Hz source with a power factor of0.65. Due to the low power factor, a 25 percent penaltyis applied at billing. If the average price of 1 kWh is$0.01 and the capacitor’s average price is $50 permillifarad, compute after how many days of operationthe penalty billing covers the price of the power factorcorrection capacitor. (To avoid penalty, the powerfactor must be greater than 0.85.)
A 240 V dc motor on brake test took 52 Amp when running at 1500 rpm. The spring balance at the end of the 76 cm brake arm reads 93.5 N. What is the efficiency of the motor at this load. [Ans. 90 %] write solution neatly
1. A resistor, in series with a 138-microfarad capacitor, is connected to a 60-cycle source. If the voltage drop across the capacitor is 115 volts and the power taken by the circuit is 922 watts, calculate (a) the circuit current, (b) the ohmic value of the resistor, (c) the line voltage, (d) the circuit power factor. Please show complete solution and the circuit diagram. Please round off answers up to the 3rd decimal place. Thank you!
A base load station having a capacity of 18 MW and a standby station having a capacity of 20 MW shares a common load. Determine the annual load factors and plant capacity factors of two power stations from the following data:Annual standby station output = 7·35 × 10^6 kWhAnnual base load station output = 101·35 × 10^6 kWhPeak load on standby station = 12 MWHours of use by standby station/year = 2168 hours
8. A factory load consists of the following : (i) an induction motor of 150 h.p. (1119 kW) with 0-7 p.f. lagging and 80% efficiency ; (ii) a synchronous motor of 100 h.p. (74-6 kW) with 0-85 p.f. leading at 90% efficiency ; (iif) a lighting load of 50 kW. Find the annual electric charges if the tariff is Rs 100 per annum per kVA maximum demand plus 7 paise per kWh ; assuming the load to be steady throughout the year. [Rs 1,96,070]
The field winding of dc motor connected across 230 V supply takes 1.15 A at room temp. at 20 deg C. After working for some hours, the current falls to 0.26 A, the supply voltage remaining constant. Calculate the final working temperature of field winding. Resistance temperature coefficient of copper at 20 deg C is 1/254.5. Answer : 70.4 Degrees Celsius How did this value arrive? According to theraja book
PLEASE SOLVE AND SHOW YOUR DETAILED SOLUTION 1. A 5-kW AC motor has a power factor of 65% lagging when it is connected to 200-V 50-Hz mains. What effective current does the motor draw? 2. In no. 1 what is the current through the motor when a capacitor of 80 μF is connected in parallel to the motor? 3. What is the power factor in the case of number 2?
The power input to a 2200 V, 50 Hz, three-phase motor running on full-load at an efficiency of 90% is measured by two Wattmeter's which indicate 350 kW and 100 kW respectively. Calculate i) Input Power. ii) Power Factor. iii) Load Current. iv) Power Output in watts. v) Power Output in hp. Input Power Answer for part 1 Power Factor Answer for part 2 Load Current Answer for part 3 Power Output in watts Answer for part 4 Power Output in hp