(a) Determine the magnitude and direction of the resultant force exerted by the liquid on the curved surface AB. The distance into the paper is 10 m. The liquid has a density of 700 kg/m3. Show all work including geometry calculations. (b) Draw the resultant force on a sketch of the problem, including appropriate dimensions and labels to identify the line of action of the force. 3 m B

(a) Determine the magnitude and direction of the resultant force exerted by the liquid on the curved surface AB. The distance into the paper is 10 m. The liquid has a density of 700 kg/m3. Show all work including geometry calculations. (b) Draw the resultant force on a sketch of the problem, including appropriate dimensions and labels to identify the line of action of the force. 3 m B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. A polyethylene bar (E = 1.4 GPa and v = 0.4) having di = 70 mm is placed inside a rigid steel tube having an inner diameter d2 = 70.2 mm. The polyethylene bar is then compressed by an axial load P. (a) At what value of P will the space between the polyethylene bar and the steel tube be closed? (b) If the compressive force P = 50 kN, determine the normal stress on the cylindrical surface of the bar, axial strain and the change in volume in the bar. Steel tube. 7p Ip Polyethylene- bar
Determine the threshold torsion
PLEASE WRITE LEGIBLY WITH COMPLETE SOLUTION SN= 77 MN= 68
To lower ends of the three bars in the figure two are the same level before the rigid homogeneous W=176kN block is attached. Each still bar has a length of 1.00 m, an area 500mm² and E=200 GPa. For the bronze bar the length is 1.6m, the area is 900mm² and E= 83 GPa. What is the stress developed in the bronze bar? What is the stress developed into steel bar? What is the elongation of each bar?
1. A circular flat plate of diameter 120 mm and thickness 10 mm is constructed from steel with E = 208 GN/m² and v=0.3. The plate is subjected to a uniform pressure of 5 MN/m² on one side only. If the plate is clamped at the edges determine: (a) the maximum deflection; (b) the position and magnitude of the maximum radial stress.
2. Consider a square bar 30 mm on side and 2.5 m long, having a material yield point 254 (in MPa). An applied axial load gradually builds up from zero to a value such that the elongation of the bar is 25 mm. Determine the permanent elongation of the bar. o = 3 oy, of = %3D 0.60y . 0.008 0.010 0.005
3. The bar shown in Figure Q4 is subjected to tensile load of 160 kN. IIthe stress is the middle portion is limited to 150 N/mm', determine the diameter of the middle portion. Find also the length of the middle portion if the total elongation of the har is to be (0.2 mm. Young's modulus is given as equal to 2. 1x 10 N/ mm. 160 EN 40 cm Figure 04
78.75 мра 33.61 MPa 22.11 MPG Determine @ Omax Omin Tmax (@s, @p) sketch the result JLULL e pain wel, w un pipar places an B , (b) the stress components exerted on the element obtained by rotating the given element clockwise through 30°. Sketch the result
A line is recorded as 472.90 m long. It is measured with 0.65 kg tape which is 30.005 m long at 20 degrees Celsius under a 50 N pull supported at both During measurement, the temperature is 5 degrees Celsius and the tape is suspended under a 75 N pull. The line is measured on 3% grade, E = 200 GPa, cross-sectional area of tape is 3 mm2 and the coefficient of linear expansion is 0.0000116 m per degree Celsius. Compute the actual length of tape during measurement Compute the total error to be corrected for the inclined distance What is the true horizontal distance?
Refer to the photo provided. Please make sure your handwriting is readable. Internal pressure and axial tensile force are applied to an open cylindrical tank 605 mm in diameter and 3.02 mm thick, resulting in the final stresses illustrated in the Mohr's circle. If a = 40.10 MPa, b = 100.06 MPa, and c = 45.05 MPa. 1. Determine the kPa value of the internal pressure. 2. What is the axial force's magnitude in kN?
Mohr circle for stress
2(c ) Problem 9.69 The masses of the blocks are ma= 30 kg and mg = 70 kg. Between all of the contacting surfaces, µ = 0.1. What is the largest force F that can be applied without causing the blocks to slip? 30 B