3. The bar shown in Figure Q4 is subjected to tensile load of 1 60 kN. IIthe stress is the middle portion is limited to 150 N/mm', determine the diameter of the middle portion. Find also the length of the middle portion if the total elongation of the bar is to be 0.2 mm. Young's modulus is given as equal to 2.1x 10 N/ mm. 160 N 40 cm Figure 04

3. The bar shown in Figure Q4 is subjected to tensile load of 1 60 kN. IIthe stress is the middle portion is limited to 150 N/mm', determine the diameter of the middle portion. Find also the length of the middle portion if the total elongation of the bar is to be 0.2 mm. Young's modulus is given as equal to 2.1x 10 N/ mm. 160 N 40 cm Figure 04

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

N.6.1. Find principle stress if the values are as given: Upper side stress:300lb/9pulg2 Tangential in right direction: 120 lb/pulg2
Two solid cylindrical rods support a load of P = 39 kN, as shown. Rod (1) has a diameter of 16 mm and the diameter of rod (2) is 11 mm. Determine the axial stress in rod 1. Assume a = 2.2 m, b = 4.6 m, c = 2.7 m, and d = 2.4 m. Use positive for tensile stress and negative for compressive stress. Express your answer in MPa rounded to the nearest whole number.
The rectangular piece of wood, 76 mm by 174 mm, is used as a compression block. The grain of the wood makes a 30.3º angle with the horizontal, as shown in the figure. Determine the shearing stress (in MPa) on the plane of the grain if the allowable compression stress on the plane of the grain is 20.2 MPa. Round off the final answer to four decimal places.
The cross section of a continuous one way slab in a building is shown in the figure. The slabs are supported by means of beams that span 3.6 m between simple supports. The dead load on the slab is 3 kPa (besides its own weight) and a live load of 7 kPa. =21 MPa, =276 MPa. Use 20 mm clear cover. Unit weight of concrete = 24 kN/m3.a) Determine the thickness of slabb) Determine the spacing of 16 mm bars at section CDc) Determine the spacing of 16 mm bars at section E.
A circular steel rod of diameter d is subjected to a tensile force P = 3.5kN The allowable stress in tension and shear are 190.6 MPa and 70.3MPa, respectively. What is the minimum permissible diameter dmin of the rod (in mm)?
Determine the maximum tensile stress σtand maximum compressive stress σc due to the load Pacting on the simple beam AB (see figure).(a) Data are P = 6.2 kN, L 5 3.2 m, d =1.25 m,b = 80 mm, t = 25 mm, h =120 mm, andh1 = 90 mm.(b) Find the value of d for which tensile andcompressive stresses are the largest. What arethese stresses?
rectangular steel plate, 1·2 m long and 850 mm wide, is subject to a compressive load along its length. If the width of the plate increases by 0·09 mm under load, determine its change in length. Take Poisson’s ratio for the steel as 0·28
The shown supported beam is 8 meters and loaded with a uniformlydistributed load of w =15 kN/m. The beam is composed of two different materials. Elastic modulus and allowable tensile/compressive strength of materials are given as E1 = 210 GPa, E2 = 70 GPa, σall,1 = 350 while MPa σall,2 = 140 MPa. what is the minimum required width b of the beam.
The following rigid structure ABCD is supported by a hinge at B and two bars at C and D. The applied load is 100 kN. The data is shown in the table. Determine: The stress in each bar. Answ: 27.01 MPa, 328.01 MPa The vertical displacement at the point where the load is applied. Answ: 0.9403 mm. The rotation at point B. Answ: 0.001069 rad. The horizontal displacement 400 mm below point B. Answ: 0.42741 mm.
A rod with a diameter of 13 mm and a length of 50 mm is subjected to a force of 50 kN. The diameter is reduced to 12.99265 mm. Determine: a. The modulus of elasticity. Answer: 200 GPa. b. Poisson's ratio. Answer: ν = 0.30 c. Shear modulus. Answer: G = 76.92 GPa. d. The deformation of the rod. Answer: δx = 0.09415 mm. Recommendation: Obtain the modulus of elasticity using the slope of the straight line.
Determine the maximum tensile stress and maximum compressive stress due to the load P acting on the simple beam AB (see figure). Data are as follows: P= 5.4 kN L=3.0 m d=1.2 m b=75 mm t_=25 mm h=100 mm h1=75 mm c1=62.5 mm c2=37.5 mm, and l= 3.3203x10⁶ mm⁴
A rectangular steel block 250 mmx100 mmx80mm is subjected to axial loads as follows. 480 kN (tensile in direction of its length) 900 kN (tensile on 250mm x 80 mm faces) 1000kN (comp. on 250mm x100mm faces) taking E=200 GN/m2 and 1/m=0.25 find a). Change in dimensions (height, width and length) b). Change in volume of the block c). Volumetric Strain c). Values of N and K (Module of Rigidity and Bulk Modulus) for material of the block. d). Determine the volume difference if the temperature of block increased by 20K. (Take alpha steel = 11.7 x 10-6 / 0C ) e). Discuss the behavioral characteristic for given application Comparing the impact from given mechanical loadings and thermal loadings to the block.