A direct time study was taken on a manualwork cycle using the snapback timingmethod. The regular work cycle consisted ofthree elements, identified as a, b, and c in thefollowing table. Element d is an irregularelement performed every 5 cycles. Observedtimes and performance ratings of theelements given. Determine the standard timefor the work cycle using an allowance factorof 15%.Work Elementaсb0.25minObserved Time0.50min0.56min100%d1.10min100%Performance Rating80%110%Select one:a. None of the AboveO b. 1.63 minutesc. 1.53 minutesO d. 1.95 minutese. 1.76 minutes

Standard Time is the amount of time it takes a qualified worker to complete a task to "Standard…

Answered: A direct time study was taken on a…

Practical Management Science

6th Edition

ISBN:9781337406659

Author:WINSTON, Wayne L.

Publisher:WINSTON, Wayne L.

Chapter2: Introduction To Spreadsheet Modeling

Section: Chapter Questions

Problem 20P: Julie James is opening a lemonade stand. She believes the fixed cost per week of running the stand...

See similar textbooks

Similar questions

A hotel housekeeper, Alison Harvey, was observed five times on each of four task elements, as shown in the following table. On the basis of these observations, find the standa rd timefor the process. Assume a I 0% a llowance factor.
A hotel housekeeper, Alison Harvey, wasobserved five times on each of four task elements, as shownin the following table. On the basis of these observations, findthe standard time for the process. Assume a 10% allowancefactor.
Use excel to show formulas 2.A job had an observed time of five minutes, a performance rating of .70, and an allowance factor of 20 percent of job time. Twenty cycles were timed. Standard time for the job in minutes is:
How many work cycles should be timed to estimate the average cycle time to within 2 percent ofthe sample mean with a confidence of 99 percent if a pilot study yielded these times (minutes):5.2, 5.5, 5.8, 5.3, 5.5, and 5.1? The standard deviation is .253 minutes per cycle.
A job was timed for 60 cycles and had an average of 1.2 minutes per piece. The performance rating was 95 percent, and workday allowances are 10 percent. Determine each of the following:a. Observed timeb. Normal timec. Standard time
Describe when is work sampling a more appropriate work measurement technique than time study ?
Nine observations from a work measurement study using continuous timing are shown below. Allowances are determined as: personal, five percent; fatigue, eight percent; delay, five percent. Use the Work Measurement Excel template to determine the standard time for this operation. Work Observation Element 1 2 3 4 5 6 7 8 9 Performance Rating A 0.09 0.14 0.08 0.07 0.10 0.09 0.15 0.14 0.15 110% B 0.23 0.20 0.22 0.20 0.24 0.23 0.29 0.27 0.27 90% C 0.49 0.51 0.49 0.46 0.49 0.49 0.51 0.49 0.48 95% D 0.64 0.66 0.63 0.62 0.69 0.67 0.67 0.66 0.70 115% E 0.72 0.74 0.74 0.69 0.81 0.82 0.79 0.80 0.82 105% F 1.01 1.03 0.99 0.99 1.09 1.12 1.03 1.07 1.12 85% Round your answer to two decimal places. minutes
Given these observed times (in minutes) for five elements of a job, determine the observed time (OT) for each element. Note: Some of the elements occur only periodically
Explain when is work sampling a more appropriate work measurement technique than time study ?
Nine observations from a work measurement study using continuous timing are shown below. Allowances are determined as: personal, five percent; fatigue, five percent; delay, seven percent. Use the Work Measurement Excel template to determine the standard time for this operation. Work Observation Element 1 2 3 4 5 6 7 8 9 Performance Rating A 0.11 0.14 0.10 0.09 0.12 0.11 0.15 0.14 0.15 105% B 0.24 0.20 0.21 0.22 0.24 0.23 0.28 0.26 0.26 85% C 0.46 0.48 0.46 0.44 0.48 0.48 0.48 0.46 0.49 100% D 0.64 0.66 0.65 0.59 0.71 0.69 0.69 0.66 0.71 115% E 0.70 0.74 0.74 0.68 0.79 0.83 0.77 0.80 0.84 100% F 1.01 1.05 1.01 1.00 1.09 1.12 1.05 1.06 1.12 95% Round your answer to two decimal places. minutes
Claudine Soosay recorded the following times assemblinga watch. Determine (a) the average time, (b) the normaltime, a nd (c) the standard time taken by her, using a performancerating of95% and a personal allowance of 8%.
A widget assembly process was timed for 75 cycles and had an average of 1.5 minutes per piece. The performance rating was 95%, and workday allowances are 10 percent. Determine the following: a) Observed time b) Normal time c) Standard time d) How might this information be used?

SEE MORE QUESTIONS

Recommended textbooks for you

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Practical Management Science

Operations Management

ISBN:

9781337406659

Author:

WINSTON, Wayne L.

Publisher:

Cengage,

Operations Management

ISBN:

9781259667473

Author:

William J Stevenson

Publisher:

McGraw-Hill Education

Operations and Supply Chain Management (Mcgraw-hi…

Operations Management

ISBN:

9781259666100

Author:

F. Robert Jacobs, Richard B Chase

Publisher:

McGraw-Hill Education

Business in Action

Operations Management

ISBN:

9780135198100

Author:

BOVEE

Publisher:

PEARSON CO

Purchasing and Supply Chain Management

Operations Management

ISBN:

9781285869681

Author:

Robert M. Monczka, Robert B. Handfield, Larry C. Giunipero, James L. Patterson

Publisher:

Cengage Learning

Production and Operations Analysis, Seventh Editi…

Operations Management

ISBN:

9781478623069

Author:

Steven Nahmias, Tava Lennon Olsen

Publisher:

Waveland Press, Inc.

SEE MORE TEXTBOOKS