A displacement sensor has an input range of 0.0 to 3.0 cm and a standard supply voltage Vs = 0.5 volts. Using the calibration results given in the table, estimate: The maximum non-linearity as a percentage of f.s.d. The constants K,, K¼ associated with supply voltage variations. The slope K of the ideal straight line. (a) (b) (c) Displacement x cm Output voltage millivolts (Vs = 0.5) Output voltage millivolts (Vs = 0.6) 0.0 0.5 1.0 1.5 2.0 2.5 3.0 0.0 16.5 32.0 44.0 51.5 55.5 58.0 0.0 21.0 41.5 56.0 65.0 70.5 74.0

Q: 7. If line frequency is 60 Hz, what is the output frequency of a bridge rectifier? 8. If the load…

A: As per the guidelines given to us, we can only provide the solution of first question in multiple…

Q: Discuss the operation of an AM demodulator circuit with emphasis on the effects of the components to…

A: A mixer or product detector is used with a local oscillator signal in the synchronous AM…

Q: Place an X under Beam Former, Signal Processor, or Image Processor to identify the location for each…

A: “Since you have posted a question with multiple sub-parts, we will solve first three subparts for…

Q: Vary the gain and time constant model parameters. How do the gain and the time constant affect the…

A: We need to explain that how do the gain and the time constant affects the system response.

Q: Another advantage of the superheterodyne receiver is “High Selectivity”. Explain how this is…

A: Both the sensitivity and the selectivity of the superheterodyne receiver are achieved in the IF…

Q: Define using your own words the sensitivity drift and bias drift, then explain how these of error…

A: Sensitivity Drift Sensitivity drift (also known as scale factor drift) defines the amount by which…

Q: When digital data '111111' is applied to the input of a 6-bit DAC, the voltage value at its output…

A:

Q: Q2) B) Use the SAR ADC to convert the analog voltage of (7.28 V) to 8-bit binary. If (VREF = 10V),…

A: Conversion table is given by, Thus the final binary output from D0 to D7 will be, 010111012

Q: Use the following figure to answer the following question: In this circuit (inverter), the…

A: When the firing angle of the rectifier is less than 30o, the expression for the output voltage for…

Q: The transition process curve of the temperature fixed-value regulation system designed and operated…

A: Given The transition process curve of the temperature fixed-value regulation system designed and…

Q: A system is described by the blöck diagram given below. Investigate the regulator characteristics of…

A: Solution- The regular characteristic of this system for a unit ramp input- To know the…

Q: Explain the role of Intermediate Frequency (IF) stage, Tuner circuit, rectifiers and amplification…

A: AM Demodulation - Demodulation refers to the process of recovering an original message signal from a…

Q: The Type K thermocouple has a sensitivity of about 41 micro-Volts/℃, i.e. for each degree difference…

A:

Q: 10.a. The type of stepper motor that has a pair of center-tapped windings is the A. closed-loop…

A: Motor:  An electric motor is a device that converts electrical energy into mechanical power. In most…

Q: 2.4) Recommend design parameters of an AM standard broadcast receiver that is to operate with an…

A:

Q: In what cases, the primary sensing elements of a generalized measurement system needs transducer?…

A:

Q: - Design a flash ADC with input voltage range [ igital output for a 2.5 V input signal?

A:

Q: Suppose a series regulator voltage is 250V, the armature current is 30A. field coils are required to…

A: A DC machine is classified in two types. DC motors DC generators Above question is based on DC…

Q: Discuss the difference between Microcontroller & System-on-Chip

A: The microcontroller is used for a specific purpose, various sensors could be interfaced to it while…

Q: . Select ONE (1) transducer or sensor with available in the market, with providing the brand, model…

A: Given data 2. Select ONE (1) transducer or sensor with available in the market, with providing…

Q: A DC chopper has 225 volts as input and the output required is 425 volts. If the non-conducting time…

A: In this question we need to find chopping frequency , new output voltage when frequency is constant…

Q: 01. AC system with rated voltage Vs=500kV, to be connected to a 6-pulse rectifier through a…

A: Note: We are authorized to answer one question at a time since you have not mentioned which question…

Q: 1) a) What is the difference between run-time and settling time? B) Define overshoot in response of…

A:

Q: Explain any two signal processing in the measurement system with neat diagrams.

A: A meter is a device used to determine the value of a quantity and is called a meter. Generalized…

Q: a. Calculate the transistor's Emitter current if it is driven by a small Base current of 7mA with a…

A: Here is a transistor is given so first write the relation between emitter collector and base current…

Q: 5. A superheterodyne receiver is tuned to a station at 3.7 MHz. The IF frequency of the receiver is…

A: Given, A superheterodyne receiver has Tuned station frequency, fs=3.7 MHz IF frequency of receiver.…

Q: 1. For the circuit in Figure 1: a) Calculate the input and output power if the input signal results…

A: NOTE:  Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the…

Q: Identify the type of signal processor element? a. Variable manipulation b. Variable controlling c.…

A:

Q: What are the advantages of using a digital system over an analog one

A: Disadvantages of Analog System- More effect on system by unwanted signal (noise) as it works on…

Q: Determine the Memory, Causality and Stability properties of the syste

A:

Q: [0 5] the signal in the volt range will be quantified. since n=4; a)Calculate what is the number of…

A: We need to calculate number of level , and step size for quantization .

Q: What are the advantages of digital system over analog system? What is the chief limitation to the…

A: In digital systems, signals are represented in binary form. There are only two states by which a…

Q: Q5: For the clamper circuit shown below. Plot the output waveforms and Compute charging and…

A:

Q: function is given by, G(s) = 90(S+9)  /   S2(S+2)(S+6) Determine  the following:

A: Here i have solved it using the information provided.

Q: What is the difference between an analog and a digital system? Provide examples that are…

A: Analog system:Analog system process the continuous signals with in the range Example :Audio…

Q: Draw a circuit diagram of the proportional (P) block of an electronic proportional, integral, and…

A: Types of Linear controller Proptional controller  Derivative controller  Integral controller  PI…

Q: Explain with a neat block diagram the measurement of displacement using strain gauge (measuring…

A: Since you posted the multiple questions so I am not solve 1st questions for you.

Q: le.) In the sensor response shown below, what type or types of error are present? Indicate all that…

A: Error: It is a difference between measured quantity and true vale.

Q: A control system is to provide a regulation of flow in range of 20gal/min to 100gal/min. A linear…

A: According to question, calculate a) What is the sensor current at 40gal/min? b) What is the range of…

Q: 20)What is the velocity error constant K, of the compensated system? V

A:

Q: 1. Suppose that you have a 12-bit, successive approximation register (SAR) A/D converter with a…

A:

Q: The Type K thermocouple has a sensitivity of about 41 micro-Volts/℃, i.e. for each degree difference…

A: The resolution of the 16 bit ADC is

Q: Q1/Define zero-crossing detector and, what is difference between inverting and non-inverting…

A: An OPAMP(operational amplifier) is an integrated electronic circuit that is used to amplify weak…

Q: An equivalent circuit for a piezoelectric accelerometer, which uses a quartz crystal as the sensing…

A: Observe the given circuit carefully, if the output voltage is Vo, then the voltage across each…

Q: the static error coefficient of the system given in the figure is Kp = 3, what should the K value be…

A: In this question we will find K value for given Kp....

Q: What is the problem of using a pushbutton or a switch as a digital input to a microcontroller. Then,…

A: We need to identify the problem of using a pushbutton or a switch as a digital input to a…

Q: c) Sketch the timing diagram with appropriate contents for the following instructions of 8085…

A:

Analog to Digital Converters

The analog-to-digital converter (ADC) allows circuits controlled by microprocessors, Arduinos, Raspberry Pi, and various reasonable digital circuits to be connected to the real world. In the real world, analog signals have a continuous stream of information from a variety of sources and sensors capable of measuring sound, light, temperature, or movement, in addition to the many digital systems that interact with their environment by measuring analog signals from those transducers.