A double cover butt riveted joint is used to connect two flat plates of 200 mm width and 14 mm thickness as shown in the figure. There are twelve power driven rivets of 20 mm diameter at a pitch of 50 mm in both directions on either side of the plate. Two cover plates of 10 mm thickness are used. The capacity of the joint in tension considering bearing and shear only, with

A double cover butt riveted joint is used to connect two flat plates of 200 mm width and 14 mm thickness as shown in the figure. There are twelve power driven rivets of 20 mm diameter at a pitch of 50 mm in both directions on either side of the plate. Two cover plates of 10 mm thickness are used. The capacity of the joint in tension considering bearing and shear only, with

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The cantilever beam is subjected to the load shown Below. Determine 1. the actual stresses acting at point A. (Hint: Tmas TIN EA). 2. IfG =30 GPa find the angle of twist at the free end of beam. 10 KN
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. Determine the spacing of rivets in mm.
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. 4. Determine the location of the centroid, in mm, from the left of the section.5. Determine the moment of inertia of the section in x106mm4.6. Determine the moment capacity of the section, kN-m, if fbcap≤300 MPa.
Q) A simply supported beam with rectangular section shown in the figure below carries a uniformly distributed service dead load of (50 kN/m) (including beam self rated service live load of (80 kN) at mid span, find: 1) Distance fo which the shear reinforcement will be applied. weight) and a conce 2) Spacing required for stirrups ®10mm at critical section. fo=22 Nimm® fy=420 N/mm? 80N +
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. 1.Determine the maximum flexural stress experienced by the beam in MPa.2. Determine the maximum shearing stress in MPa at Neutral Axis.3. Determine the spacing of rivets in mm.
PLS ANSWER. BADLY NEEDEDSimply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials.1.Determine the moment of inertia of the section2.Determine the maximum positive bending moment in the beam in kN-m.
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. a. Determine the location of Neutral Axis, in mm, from the top of the section.b. Determine the location of the centroid, in mm, from the left of the section.
Simply Supported Beam ABCDE below carries multiple loads as shown. A built-upsection made from a T-Section and a Channel (C-Section) fastened together by 16mm∅ bolts,equally spaced from the center of the section, with shearing capacity τ=100 MPa, for bearing σb= 220 MPa for rivets in single shear and σb = 280 MPa for rivets in double shear. E=200GPa forall materials. Determine the location of the centroid, in mm, from the left of the section.
Two 4-in.-wide wooden boards are to be joined by splice plates that will be fully glued onto the contact surfaces, as shown in the figure. The glue to be used can safely provide a shear strength of 140 psi. Determine the smallest allowable length L that can be used for the splice plates for an applied load of P = 20,000 lb. Note that a gap of a = 0.8 in. is required between boards (1) and (2).
A square hollow steel strut if thickness 10mm is pin connected to two connector plates of thickness, 12mm. The connector plates are welded to the base plate of thickness, 12mm. The base plate is fastened to te concrete base by 4-16mm diameter anchor bolts. The diameter of the pin is 16mm. Which of the following most nearly gives the shearing stress in the anchor bolts? Choices 150.00 MPa 59.68 MPa 51.69 MPa 119.37 MPa
Assume that the axial load P = 40kN applied to the lap joint is distributed equallyamong the three rivets. What is the smallest diameterof the rivetif the allowable stresses are 90 MPa for bearing between a plate and a rivet, and 40MPa for shear in rivets?
A built-up beam made from fastening two channels to a wide flange section carriesloads` as shown. The fasteners are 12mm∅ bolts with allowable shear stress τ= 110 MPa. Forbearing, σb= 220MPa for single shear, and σb= 275 MPa for double shear. E=200 GPA. Fy=420MPa. Do not round off between solutions . Explain the Stepsa.) Determine the Moment of Inertia of the Sectionb.) Determine the Moment Capacity of the section if fb≤280MPa