[Unit: mm]100500stirrupstirrupA,A200030020003002000The simple span of the beam is 6 meters. Use f'c = 28 MPa and fy = 420 MPa. Calculate theeffective depth based on the minimum beam design requirements. Determine the number ofØ25-mm bars needed to bear a uniform dead load of 6 kPa (including concrete weight) and alive load of 10 kPa on an inside T-beam indicated in the picture. Make all of the required checks.

Answered: Image /qna-images/answer/6783a4e6-e163-4acb-acf1-e21286c99e66.jpg

Answered: The simple span of the beam is 6…

Engineering

Civil Engineering

The simple span of the beam is 6 meters.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. A simply supported 5 meter timber beam carries a 5kN/m uniformly distributed load. If the beam’s Ix is 260.4166 x 10^6 mm^4 and fb= 7.50 MPa, the maximum moment development is? a) 14.656 kN-m b) 15.625 kN-m c) 16.625 kN-m d) 17.625 kN-m 2. What is VMax for the beam of question 1? a) 10.5 kN b) 11.5 kN c) 12.5 kN d) 13.5 kN 3. What is the beam’s depth of question 1? a) 180 mm b) 200 mm c) 220 mm d) 250 mm
A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 2 m on centers, on simple supports over a span of 6.0 m. The floor supports a superimposed service dead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c = 21 MPa, long bar fy = 415 MPa, calculate: 8. Using a T-beam geometry formed from monolithic construction, determine the effective flange width of a typical interior beam in mm. = [bf] mm
Calculate the total equivalent uniform load in KN/m on Beam AB, if the total floor load is 11.56KPa. Use a=3.7m, b=5.8m . Express your answer in 2 decimal places.
Given: Mmax= 15.625 kN-m Vmax= 12.5 kN Depth of the beam= 250 mm 1. A simply supported 5 meter timber beam carries a 5 kN/m uniformly distributed load. If the beam's Ix is 260.4166 x 10^6 mm^4 and fb = 7.50 MPa, what is the base of the beam? a) 150 mm b) 180 mm c) 200 mm d) 220 mm 2. The shear stress fv developed for the beam of question 1 is a) 0.375 MPa b) 0.50 MPa c) 0.75 MPa d) 0.85 MPa
A simply supported beam with a span length of 4.8 m is laterally supported atits ends and is subjected to a dead load = 8 kN/m (including the weight of thebeam) and live load = 10 kN/m. If Fy = 345 MPa, is a PIPE8SCH80adequate?
A floor slab 100 mm thick is cast monolithically with beams 300 mm wide 500 mm deep spaced 1.5 m on centers, on simple supports over a span of 6.0 m. The floor supports a superimposed service dead load of 1.77 kPa and service live load of 4.8 kPa. Using f’c= 21 MPa, long bar fy = 415 MPa, calculate Using a T-beam geometry formed from monolithic construction, determine the effective flange width of a typical interior beam in mm.
A cantilever R.C. beam is 280 mm x 500 mm deep and is reinforced with 4- 20 mm diam bars for tension. Using an effective depth of d = 450 mm, determine if the 2.50 m long beam is adequate to carry a uniform load of 15 KN/m and a concentrated load of 10 KN at the cantilever end in 2 ways. Use f’c = 21 MPa, fy = 275 MPa. Neglect the weight of beam. Use n = 9.Determine if the catilever beam is adequate based on strength design 2001 NSCO specifications. The 15Kn/m load is DL while the 10KN load is LL.
A floor slab 100 mm thick is cast monollthically with beams 250 mm wide 450 mm deepspaced 1.2 m on centers, on simple supports over a span of 5.0 m. The floor supports asuperimposed service dead load of 1.0 kPa and service live load of 2.1 kPa. Using f.=21MPa, long bar f, = 415 MPa, calculate the following:Factored uniform load on a typical interior beam in kN/m using load factors of 1.2for dead load and 1.6 for live load.A. 8.928B. 11.448C. 11.028D. 9.960Effective flange width of a typical interior beam in mm.A. 1,500B. 1.850C. 1.200D. 1.466Required amount of 16-mm-flexure bars for a typical interior beam in positivebending. Use 10-mm-dia. stirrupsA. 512 mm2B. 246 mm2C. 331 mm2D. 427 mm2
Please help with this practice question. Thanks Question 1 ) determine the counterweight J in order for the main jib DCB to be horizontal. (The units should be in kN)
A rectangular beam with a simple span of 6 m, supports a dead load of 17.50 kN/m and a live load of 36.5 kN/m. For architectural reasons the cross section is limited to 300 mm width and a total depth of 540 mm, with an effective depth of 460 mm. The dead load includes the weight of the beam. If f’c = 20.68 MPa, fy = 275.8 MPa.Determine the factored uniform loadDetermine the steel area required for compressionDetermine the steel area required for tension.
A rectangular beam has the following properties: b = 300 mm, d = 350 mm, tension bars As = 4-28mmØ, compression bars As’ = 2-28 mmØ, d’ = 60 mm. Determine the design strength of the beam.a. 233.155 kN.m. c. 636.511 kN.m.b. 332.511 kN.m. d. 755.321 kN.m. Calculate the ultimate axial load capacity of a round spiral column having a diameter of 400 mm reinforced with 6-20 mm Ø bars having fc’ = 24 MPa and fy = 276 MPa. a. 1941.401 kN c. 1841.321 kNb. 9141.401 kN d. 8141.321 kN
A simple beam of length L 5 5 m carries auniform load of intensity q 5 5.8 kN/m and a concentratedload 22.5 kN (see figure).(a) Assuming σallow =110 MPa, calculate therequired section modulus S. Then selectthe most economical wide-flange beam (Wshape) from Table F-1(b) in Appendix F, and recalculate S, taking into account the weight ofthe beam. Select a new beam if necessary.(b) Repeat part (a), but now assume that the designrequires that the W shape must be used in weakaxis bending (i.e., it must bend about the 2–2(or y) axis of the cross section).