A double threaded right-handed worm gear transmits 15 hp at 1150 rpm. The pitch of the worm is 0.75 inches and pitch diameter of 3 inches. The pressure angle is 14.5 deg and the coefficient of friction is 0.12. Determine the following: a) the normal diametral pitch b) the power output of gear c) the diametral pitch d) the pitch line velocity of worm e) the expected value of the tangential force on worm f) the expected value of the separating force.

A double threaded right-handed worm gear transmits 15 hp at 1150 rpm. The pitch of the worm is 0.75 inches and pitch diameter of 3 inches. The pressure angle is 14.5 deg and the coefficient of friction is 0.12. Determine the following: a) the normal diametral pitch b) the power output of gear c) the diametral pitch d) the pitch line velocity of worm e) the expected value of the tangential force on worm f) the expected value of the separating force.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

a double threaded worm gear transmits 15 Hp at 1150 rpm. the pitch of the worm is 0.75" and pitch diameter is 3". the pressure angle is 14.5 degrees and coefficient of friction is 0.12. Find the worm gear efficiency
A motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm thickness at rate of 35 holes per minute. It requires a torque of 7 Nm for an area of hole in mm2. If the cutting takes 1/10 of a second and the speed of its flywheel varies from 165 rpm to 145 rpm, calculate: 4.1. Energy required to cut a hole. (4) 4.2. Energy required for cutting work per second. (2) 4.3. Maximum fluctuation of energy of the flywheel. (4) 4.4. Mass of the flywheel having radius of gyration of 1.5 m.
A motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm thickness at rate of 35 holes per minute. It requires a torque of 7 Nm for an area of hole in mm². If the cutting takes 1/10 of a second and the speed of it's flywheel varies from 165 rpm to 145 rpm, calculate 4.1)Energy required to cut a hole 4.2)Energy required for cutting work per second. 4.3)Maximum fluctuation of energy of the flywheel 4.4)Mass of the flywheel having radius of gyrations of 1,5 m
A spur gear has a module of 5 mm, 60 teeth, and a pressure angle of 20° with full-depth teeth. The face width of the gear is equal to 4 times the circular pitch. Using the Marin size factor ?௕, determine the size factor ?௦ . Please solve question briefly, it is very important.
A motorised metal guillotine machine is required to cut 45 mm diameter hole in a plate of 20 mm thickness at rate of 35 holes per minute. It requires a torque of 7 Nm for an area of hole in mm2. If the cutting takes 1/10 of a second and the speed of its flywheel varies from 165 rpm to 145 rpm, calculate:4.1. Energy required to cut a hole.4.2. Energy required for cutting work per second.4.3. Maximum fluctuation of energy of the flywheel.4.4. Mass of the flywheel having radius of gyration of 1.5 m.
A 20◦ helical gear has tangential force of 200lb and helix angle of 16◦ and face width of 0.6”.If the machining error is 0.6 and pitchline velocity is 400ft/min. Determine radial force, axial force, normal force, normal pressure angle and dynamic load.
Q.8 A pair of helical gears in which teeth on pinion are 20 and on gear are 30, the normal module is 5 mm and normal pressure angle is 20°. The helix angle is 30°. The pinion is provided 5 kW at 720 rpm. Determine various forces on the teeth.
Provide the complete step-by-step solution, given data, conversion of units, and sketch for this problem. A turbine at 30,000 rpm is used to drive a reduction gear delivering 3 hp at 3,000rpm. The gears are 20 degrees involute herringbone gears of 28 pitch and 2 1/8 ineffective width. The pinion has 20 teeth with a helix angle of 23 deg. Determine theload normal to the tooth surface. A. 20.4 lbs B. 24.4 lbs C. 28.4 lbs D. 32.4
A high-speed steel tool is used to turn a steel workpart that is 295 mm long and 75 mm in diameter. The parameters in the Taylor equation are: n = 0.15 and C = 80 (m/min) for a feed of 0.5 mm/rev. The operator and machine tool rate = $29.00/hr, and the tooling cost per cutting edge = $3.90. It takes 2.1 min to load and unload the workpart and 3.40 min to change tools. Determine (a) cutting speed for maximum production rate, (b) tool life in min of cutting, and (c) cycle time and cost per unit of product (d) cutting speed for minimum cost and tool life in min of cutting
The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A is mounted on an electric motor with a rotational speed of 600rpm. Gear A drives a simple gear train consisting in gears B, C, D, and E and transfers the input power to each gear to the shaft on which is mounted. The power delivered from shafts B, C, D, and E are: 8hp, 12hp, 5hp, and 5hp, respectively. For simplicity, all gears have a diametral pitch of 3 and the following numbers of teeth: NA=75, NB=15, NC=120, ND=15, NE=36. The torque on shaft D is most likely: 2015 lb in 105 lb in 250 lb in 630 lb in
The figure below shows the power transmitted through a gear drive to multiple output shafts. Gear A is mounted on an electric motor with a rotational speed of 600rpm. Gear A drives a simple gear train consisting in gears B, C, D, and E and transfers the input power to each gear to the shaft on which is mounted. The power delivered from shafts B, C, D, and E are: 8hp, 12hp, 5hp, and 5hp, respectively. For simplicity, all gears have a diametral pitch of 3 and the following numbers of teeth: NA=75, NB=15, NC=120, ND=15, NE=36. The expected rotational speed on shaft E is most likely: 375 rpm 600 rpm 1250 rpm 3000 rpm
In a gear set, a 36-tooth spur pinion drives a 60-tooth spur gear. The teeth of these gear are cast iron profile. The diametral pitch is 6-teeth/in, the face width si 0.5 inches, and the pressure angle is 20 degrees. Assume that the pinion transmits 10 hp at a speed of 2000 rpm. Find the pitch diameters of the gears. Find the pitch line velocity in ft/min Find the velocity factor Ky Find the tangential load in lbf Find the contact stress in kpsi, assuming CP=1960 psi.