5. Determine the support forces and force in each member of the truss in Fig. Q5 and state if the members are in tension or compression. 1.5 m 2 m B 4 kN Fig. Q5 3 kN 2 m 10 = 30° a) Draw FBD of truss ABCD and determine support forces at A and C. b) Draw FBD of pin at C. Determine unknown member forces. c) Draw FBD of pin at B. Determine unknown member forces. d) Draw FBD of pin at A. Determine unknown member force. [Ax=1.2kN, A,-0.88kN, C,-1.8kN, Cy=3.13kN, FBC= 2.37(T), FcD= 5.21(C), FAB= 2.37(T), FBD= 4.0(T), FAD= 1.47(C)]

5. Determine the support forces and force in each member of the truss in Fig. Q5 and state if the members are in tension or compression. 1.5 m 2 m B 4 kN Fig. Q5 3 kN 2 m 10 = 30° a) Draw FBD of truss ABCD and determine support forces at A and C. b) Draw FBD of pin at C. Determine unknown member forces. c) Draw FBD of pin at B. Determine unknown member forces. d) Draw FBD of pin at A. Determine unknown member force. [Ax=1.2kN, A,-0.88kN, C,-1.8kN, Cy=3.13kN, FBC= 2.37(T), FcD= 5.21(C), FAB= 2.37(T), FBD= 4.0(T), FAD= 1.47(C)]

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The given plane truss structure below is (where truss member BD is a single member and should not be considered as 2 members) A. Statically determinate B. Statically indeterminate with redundant truss members C. Statically indeterminate with deficient truss members D. Can’t be determined
Determine all of the forces of the members. Method of Henneberg.
Determine Reaction and Internal Member Forces
A boom hinged at the base of a vertical mast is used to lift a 2000 lb load. Find the tension in the cable and the reaction R at the end of the boom. The angle of the boom is 40 degrees with the horizontal and the cable is 60 degrees with the vertical mast. Pls include given, formula, fbd, and solution.
Solve the truss structure using the joint's method, when m = 100 kg.
Question 8 A weight of 1467 N resting over a smooth surface inclined at 30° with the horizontal, is supported by a weight (P) resting on a smooth surface inclined at 45° with the horizontal as shown in figure. Determine the weight P.
Given: F1=5 kN F2=12 kN F3=4 kN F4= 11 kN L=8 m Determine the force in member CF by the method of sections.
In engineering, a truss is a structure that "consists of two-force members only, where the members are organized so that the assemblage as a whole behaves as a single object”. Based from Figure 2 below, determine the force in each member of the truss, and state if the members are in tension or compression. Set θ = 0°.
4.7 a) Member-AD is_____. options: 1 a two-force member 2 a multi-force member 3 a zero-force member 4 a torsional member b) Member-BF is _____. options: 1 a two-force member 2 a multi-force member 3 a zero-force member 4 a torsional member c) Member-CE is _____. options: 1 a two-force member 2 a multi-force member 3 a zero-force member 4 a torsional member d) The section of rope between Member-AD and Sheave-F is _____. options: 1 a two-force member 2 a multi-force member 3 a zero-force member 4 a torsional member e) The section of rope between Sheave-F and the load is _____. options: 1 a two-force member 2 a multi-force member 3 a zero-force member 4 a…
A 2.0m long bar is being used as a first-class lever. It has a load of 720 N placed on one end (located 1.2 m from the fulcrum) and the effort is being applied at the opposite end. A. State the law of the leaver B draw a diagram of the lever, showing the load,effort,fulcrum, effort arm, and load C determine the effort force needed to balance the load. D if this lever has an actual mechanical advantageous 1, determine the percent efficiency of the leaver.
Hi I need help with this question and answering the steps for it An 650-N painter stands 2.3 m from the right side of a 9-m-long beam of a scaffold, which is connected to cables at each end. The force exerted by Earth on the uniform beam is 246 N. Determine the forces that the cables exert on each end of the beam. Assume that g=10\frac{\text{N}}{\text{kg}}g=10kgN Draw a sketch of the situation, labeling all of the physical quantities given in the problem. Identify your system in the sketch. Make sure all relevant moments in time are shown in your sketch. Draw an extended-body force diagram showing all of the forces exerted on the bean and the points at which those forces are being exerted. Solve for force each cable exerts on the beam. Start with general equations and explain what you are doing and why you did what you did. Evaluate your solution. Describe how you evaluated your answer and whether or not you think your answer is reasonable.
Determine the force in each member of the truss shown in (Figure 1). State if the members are in tension or compression. Take that P = 420 lb. Express your answer to three significant figures and include the appropriate units. Assume positive scalars for members in tension and negative scalars for members in compression. Given: angle to use is 36.9 degrees, FCD = 700lb FAD =-560lb Find: a) Determine the force in the member BC of the truss, and state if the member is in tension or compression. b) Determine the force in the member AC of the truss, and state if the member is in tension or compression. c) Determine the force in the member AB of the truss, and state if the member is in tension or compression.