a) Draw the block diagram of the phase locked loop detector that can be used to detect FMsignal and explain the operation of this circuit?b) Draw clearly the block diagrams of the coherent and non-coherent detectors that can beused to demodulate AM signals?c) Sketch the block diagrams for the AM-DSB-SC and AM-SSB-SC showing clearly theirspectrums that contains a carrier signal with a frequency fe and a massage signal with afrequency fm

Since you have asked multiple question, we will solve the first question for you. If you want any…

Answered: a) Draw the block diagram of the phase…

a) Draw the block diagram of the phase locked loop detector that can be used to detect FM signal and explain the operation of this circuit?

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

-MCQ- FM modulator is used to transmit a cosine message signal with 4V amplitude and 20Hz frequency. The frequency deviation constant kf = 25 Hz/V, the carrier is a cosine sign with an amplitude of 10V and a frequency of 2000Hz. The FM modulated signal is passed through a bandpass filter and 90% of the power of the modulated signal remains. What is the bandwidth of the FM modulated signal in this case? a) 240hz b) 20hz c) 100hz d)200hz
In Amplitude modulation, Vestigal Side Band (VSB) is one of the technique used to overcome its limitations in terms of power and bandwidth. With this in mind; a. Explain how a VSB signal is generated in the transmitter. b. Draw and compare the frequency spectrum of the original message signal and the spectrum of the VSB signal in a frequency domain. c. Show how the bandwidth of VSB is calculated by writing the equation. d. Give one application of VSB in broadcasting.
When the amplitude of an SSB transmitter's modulating signal is reduced to zero:Answers are as following? Which one ıs correct? a)the BFO should produce an increased frequency at its output. b)one of the two sidebands drops to zero and the other one increases to c)twice its original value due to an imbalance in the BFO. d)the receiver's output amplitude also drops to zero. the AGC responds by increasing the carrier amplitude in the receiver.
A signal transmission line which has a source impedance of 75Ω is to be connected to a signal strength meter of impedance 50Ω which has a maximum display of 18dB. Calculate the values of resistors required in an L-pad attenuator circuit to operate the meter at maximum power (towards small impedance). And also determine minimum insertion loss and minimum attenuation in dB.
1.Select the correct statement(s) regarding frequency modulation (FM) bandwidth. a. the more the carrier frequency is allowed to change frequencies (Δf), the smaller the modulated signal bandwidth b. the larger the FM index, β, the larger the modulated signal bandwidth c. as you increase kvco, you decrease modulated signal bandwidth d. all statements are correct 2. Select the correct statement(s) regarding baseband signal modulation. a. with modulation, a baseband signal can be moved to a higher frequency thus preventing baseband signal interference b. modulation techniques are only required for analog information signals, since digital signals are represented by discrete logical values of “1” and “0” c. modulation eliminates the baseband signal’s frequency bandwidth, thus enabling greater efficiencies when transmitting a modulated carrier signal d. all statements are correct 3. A…
A. How many numbers of constellation points exist in phase for 3bit ASK? B. What happens to the radio wave propagation when the frequency is below critical angle? C. If the mark frequency and space frequency are same then what happens to FSK? D. What is the Carson’s rule? E. What is the Maximum data rate in a minimum channel bandwidth is ? F. What is radio horizon and where is it used? G. What are the phase angle limitations of a BPSK? H. What is the change in channel capacity when two number of bits are increased?
An Amplitude Modulation (AM DSBFC) radio broadcasting station with its carrier frequency of 750 kHz is amplitude-modulated by a 4 kHz audio signal to produce an AM envelope. The maximum and minimum peaks voltages of the envelope are 180Vp and 70Vp respectively. The equivalent resistance of the transmitting antenna is 60 Ω. Determine: (i) The peak amplitudes of the audio, carrier sideband voltages and modulation index. (ii) Using the above results, write the complete AM mathematical representation to express the waveform, showing its carrier, lower sideband and upper sideband parameters. (iii) The power of the carrier signal, total sidebands power and the bandwidth of the modulated signal. Then sketch and label the power spectrum of the modulated ( i v ) If the transmission is changed to Single-Side Band Suppressed Carrier (SSBSC), calculate the percentage power saving in comparison to the original AM DSBFC
We use modulation in communication system for many reason, one of the reason for using it in AM is: A. The message signal can transmitted faster with modulation compared to the same signal without modulation. B. To attach interference to the modulated signal in order to transmit it through the medium C. The modulator enhance the noise in the modulated signal using a band pass filter D. The modulator allows controlling the phase of the carrier signal, thus controlling the carrier phase. E. To control the demodulator on the receiver and extract a message signal F. To obtain a active transmitting and receiving of the modulated signal through the antenna
1. For a system with FM modulation, the amplitude of the unmodulated carrier is 12Vp, if the modulation index is 1.5 and the load resistance RL is 10 ohms,a) determine the power in the unmodulated carrier; b) Determine the power at the carrier frequency and at each significant side frequency for the modulated wave. What value of power do you obtain when adding the values obtained in question (b)?
5. Why must modulated signals be demodulated?A. To recover the original intelligenceB. To improve the spectral efficiency of digital transmissionsC. To enable implementation of advanced featuresD. To produce one or more significant sideband pairs
A 1500 KHz carrier with amplitude of 50 V is amplitude modulated by 2 –KHz sine wave tone with a peak voltage of 15 V. Determine the modulation index, percent modulation, the upper and lower sideband frequencies, bandwidth of the wave, and write the AM equation.
What is true regarding an information signal viewed in the timeand/or frequencydomains. a. the bandwidth of a signal can only be viewed in the time domain b. signal bandwidth can be viewed in the frequency domain c. signal amplitude can only be viewed in the time domain d. there are no true statements 2. Select the correct statement(s) regarding baseband signal modulation. a. modulation involves the mixing of a baseband signal with a carrier to produce a modulated carrier (passband) signal b. the modulation index gives us information regarding the quality of the modulated carrier signal c. FM and PM modulation techniques are categorized as “angular modulation”, while AM is not considered an “angular modulation technique d. all statements are correct