A ferromagnetic core with a relative permeability of 2000 is shown in Figure. The dimensions are as shown in the cm 30 cm 7 cm diagram, and the depth of the core is 7 cm. The air gaps on the left and right sides of the core are 0.050 and 0.070 cm, respectively. If there are 300 turns in the coil wrapped around the center leg of the core and if the current in the coil is 1.0 A, what is the flux in each of the left, center, -0.05 cm 300 um 30 cm 0.07 cm- 7 cm and right legs of the core? What is the flux density in each air gap?

A ferromagnetic core with a relative permeability of 2000 is shown in Figure. The dimensions are as shown in the cm 30 cm 7 cm diagram, and the depth of the core is 7 cm. The air gaps on the left and right sides of the core are 0.050 and 0.070 cm, respectively. If there are 300 turns in the coil wrapped around the center leg of the core and if the current in the coil is 1.0 A, what is the flux in each of the left, center, -0.05 cm 300 um 30 cm 0.07 cm- 7 cm and right legs of the core? What is the flux density in each air gap?

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter6: Power Flows

Section: Chapter Questions

Problem 6.61P

See similar textbooks

Similar questions

A transformer has primary and secondary turns of 1250 and 125 respectively. It has core cross-sectionof 36 cm2 and its rms flux density is to be limited to 1.4 T (to prevent core saturation). Whatmaximum 50 Hz voltage can be applied on the primary side and the corresponding open-circuitsecondary voltage?The core has a mean length of 150 cm and its relative permeability can be assumed to be 8000. Whatwould be the rms exciting current when the transformer’s primary winding is excited at a voltage ascalculated above? Also calculate the magnetizing susceptance as seen from primary and secondarysides.If the transformer were to be excited at 60 Hz, 1. What should be the maximum primary voltage for thecore flux density limit not to be exceeded? 2. What would be the magnetizing susceptance as seen oneach side in this case?
Consider a ferromagnetic ring (nucleus) that has a mean circumference of 40 cm, 300coiled copper turns and a sectional area of 5 cm2. A current of 2 is appliedA to winding, producing a flux of 1.5 mWb.Determine the permeability of the core material.Determine the relative permeability of the core material.If the ferromagnetic ring has an air gap of 2 mm. Find the required MMFso that the flux density in the gap is 0.5 T.
1- Please, Derive Equation of Motion for the 2DOF system with Harmonic force due to the Shaker in the Magnetostrictive Energy Harvesting. Note: I want EOM in Matrices form to get Natural frequencies and mode shapes + Steady-State Response of Spring-Mass System
A ferromagnetic core with a relative permeability of 1500 is shown in the following figure. The depth of the core is 5 cm. Because of fringing effects, the effective area of the air gaps is 5 percent larger than their physical size. If there are 300 turns in the coil wrapped around the center leg of the core, and if the current in the coil is 1.25 A, find the magnetic flux and the field density in all three legs of the core, as well as the magnetic flux and flux density in the two air gaps.
please explain the operating principle of single phase 2S-2P PMSM based on 3D design illustration.
- An 8-pole wave -wound d.c generator with output current is 200 A and has ATc/pole = 2600 AT and ATd /pole= 400 AT. Find the number of conductor.
A ferromagnetic core is shown in Figure 1. The relative permeability of the core isassumed to be 2500 and constant. There is a 5% increase in the effective area ofthe air gap due to fringing effects. The depth of the core is given as 5 cm. The Rtotal is found to be 226.192k At/Wb
Draw the per-phase equivalent circuit of a three-phase squirrel-cage induction machine. List all of the elements in the equivalent circuit and briefly state their function
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
Draw a block diagram of a phase-locked loop (PLL) and briefly explain its operation.
1) A ferromagnetic core is shown in Figure 1. The relative permeability of the core isassumed to be 2500 and constant. There is a 5% increase in the effective area ofthe air gap due to fringing effects. The depth of the core is given as 5 cm.a) Calculate the total reluctance, total, of the core
Using Kirchhoff's Law, determine the load currents. All The possible current and voltage equations. With complete solutions