A field – compact sample of sandy loam was found to have a wet density of 110.4 b/ft3 at a water content of 14%. The maximum dry density of the soil obtained in a Standard Proctor Test (SPT) was 99.6 b/ft3. Assuming specific gravity of soil sample to be 2.6, determine the percent compaction of the field.

A field – compact sample of sandy loam was found to have a wet density of 110.4 b/ft3 at a water content of 14%. The maximum dry density of the soil obtained in a Standard Proctor Test (SPT) was 99.6 b/ft3. Assuming specific gravity of soil sample to be 2.6, determine the percent compaction of the field.

Principles of Foundation Engineering (MindTap Course List)

8th Edition

ISBN:9781305081550

Author:Braja M. Das

Publisher:Braja M. Das

Chapter16: Soil Improvement And Ground Modification

Section: Chapter Questions

Problem 16.2P

See similar textbooks

Similar questions

A sand cone test has been performed in a recently compacted fill. The test results obtained are as shown in Table 3(b). (i) Determine the dry density of compaction in the field (ii) Calculate the maximum dry density from standard Proctor test if the relative compaction is 90%. (iii) Determine the degree of saturation of the compacted fill if the specific gravity of the soil is 2.65.
For a silty clay soil given LL = 43 and PL = 18. Estimate the maximum dry unitweight of compaction that can be achieved by conducting a modified Proctor test. Use Eq attached.
A compaction test was performed on a soil sample from a proposed cut area. The maximum dry unit weight and optimum moisture content were determined to be 104.8 lb/ft3 and 20.7% respectively. What is the possible type or classification of soil for this sample?
It has been anticipated that the soil under the proposed dam is contaminated, and needs to be removed and backfilled to a depth of 2.5 feet. A Standard Proctor compaction test was conducted on soil from a borrow pit, with the results shown below right. Based on the results: a) Plot the Proctor curve for the borrow soil. b) Find the optimum water content and max. dry unit weight for the borrow soil. c) Determine whether the unit weight of the top layer can be met by compacting to 95% of maximum, and what the range of moisture content for that unit weight is. d) If we borrow soil from a pit with a void ratio of 0.71, determine how much soil we need to borrow to backfill below the dam to match the in-situ void ratio of the top layer of soil.
The results of compaction test in the laboratory using the standard proctor method for the Ayer Hitam residual soil are tabulated in Table Q1(c). After compaction of the soil in the laboratory, the field density tests using the sand cone replacement method were performed. Assume the specific gravity, Gs = 2.65. (i) Determine the maximum dry density and optimum moisture content from compaction curve. (ii) Ayer Hitam residual soil will be used as a compacted layer with thickness of 4 m high. If the moisture content of the compacted soil at the field is 15.8%, determine the vertical stress (kN/m³) at a depth of 2.5 m from the ground surface.
The results of a standard Proctor test are given in the following table. Determine the maximum dry unit weight of compaction and the optimum moisture content. Also determine the moisture content required to achieve 90% of ꙋd (max).
A 1 m thick soil with an initial void ratio of 0.94 was compacted by a roller and its thickness reduced by 0.09 m. The specific gravity of this soil is 2.65. A 178.0 g soil sample was collected from the compacted soil mass to examine the degree of compaction. The sample was dried in an oven for 24 hours and it had a dry mass of 142.4 g. Determine the degree of saturation of the soil after the compaction.
A saturated 100 cm3 clay sample has a natural water content of 30%. It is found that the shrinkage limit occurs when the water content is 19%. If the specific gravity of soil is 2.70, compute: A. The shrinkage ratio B. The volume of sample when the water content is 15% C. The mass of dry soil sample
A compacted sample of soil with a bulk density of 125 pcf has a water content of 15%. What are its dry density, degree of saturation and air-content? Assume Gs = 2.65. If the sample is allowed to get fully saturated, without any increase in its volume, what would be its bulk density?
From a standard Proctor laboratory sample of soil Gs= 2.70; maximum dry unit weight = 16.4 kN/m3; Optimum moisture content= 18%; Moisture content of soil at the borrow site+ 28%. Specification require that compaction of soil must be at least 95% of the maximum obtained from the proctor test. Compute the maximum compaction expected from the compacted soil using the zero air boids curve for this soil with the following moisture contents: w1= 20%; w2= 25%; w3= 30%.
Sand is used in the cone is known to have a bulk density of 15.74 kN/m3 Wet weight=20.601 N Dry weight =17.926 N Weight of sand to fill test hole =16.053 N a) Determine the in-place dry density of the tested soil (Ans. 17.57 kN/m3) b) Determine the water content (Ans. 15%) c) Compute the percentage of compaction of the tested soil if the laboratory moisture density curve indicates a dry density of 18.1 kN/m3 and an optimum moisture content of 13%. (Ans. 97.07%)
The specific gravity of soil is 2.7 and the porosity of mentioned soil is 0.26. Calculate saturated unit weight and dried unit weight of this sample