a) Find the average power dissipated in the line shown. b) Find the capacitive reactance that when connected in parallel with the load will make the load look purely resistive. c) What is the equivalent impedance of the load in (b)? d) Find the average power dissipated in the line when the capacitive reactance is connected across the load.

a) Find the average power dissipated in the line shown. b) Find the capacitive reactance that when connected in parallel with the load will make the load look purely resistive. c) What is the equivalent impedance of the load in (b)? d) Find the average power dissipated in the line when the capacitive reactance is connected across the load.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.24P: A source supplies power to the following three loads connected in parallel: (1) a lighting load...

See similar textbooks

Similar questions

The admittance for a circuit, G + jB, is 0.02 + j0.20. What is the impedance, R + jX? Provide illustration of the circuit.
Find the instantaneous and RMS voltage of the series RC circuit if the circuit element has R = 10 ohms, L = 24mH. The total instantaneous current is i(t) = 10 sin 377t, amps. Show your solution using 2 different approaches.
Identify: a. Three loads are in parallel take the following currents: i1 = 10 sin 314t; i2 = 20 sin (314t -45º); i3 = 30 cos (314t + 30º) A. respectively. Find the rms value of the resultant current.b. A 40 μF capacitor is supplied with a 100 V, 60 Hz source. Find the resulting current.
Please solve for following based on attached circuit: average laod current RMS load current average load power absorbed apparent source power
Identify: a. A 40 μF capacitor is supplied with a 100 V, 60 Hz source. Find the resulting current. b. Three loads are in parallel take the following currents: i1 = 10 sin 314t; i2 = 20 sin (314t -45º); i3 = 30 cos (314t + 30º) A. respectively. Find the RMS value of the resultant current.
solve for the total complex, apparent, average, and reactive power. sketch the power triangle
A capacitor of 3.18 microfarads is connected in parallel with a resistance of 2000 ohms. The combination is further connected in series with an inductance of 795 mH and resistance of 100 ohms across a supply given by e=400 sin + 80 sin(3wt + 60O). Assume w = 314 rad/sec, determine the rms value of the total current.
The load is connected to 100V (rms) and dissipates 1kW at lagging power factor of 0.9. Find the phasor V1 where VL=100<0 degree and frequency equals 400 rad/s.
A series circuit of RLC with following parameters, R=15 ohm, L=20 m H & C=100 micro Farad. VT=169.7 sin (337t-30) Volt. Find the following: Zt, , It, Voltage across each element, Power factor, apparent power, real or average power and reactive power and the total phasor diagram and power phasor diagram
The instantaneous power of a parallel RL load is given by 300{1+cos(628.32t+400)} + 400sin(628.32t+400) W. Answer the following (with appropriate units). Real Power: Reactive Power: Apparent Power:
Power Electronics A sinusoidal voltage source v(t) = 240 sqrt(2) sin(2pi60t) V is applied to a non-linear load, giving rise to a current i(t)= 10sin(2pi60t) + 5 sin(4pi60t) A. Determine: (a) the power absorbed by the load
A sinusoidal voltage source V = 53 /67o Vrms feeds an impedance with a current I = 5 /33o Arms. The apparent power generated by the source is: Select one: a. 118.64 VA b. 80.02 VA c. 286.2 VA d. 265 VA e. 71.55 VA