A flanged bolt coupling consists of six 12-mm diameter steel bolts evenly spaced around a bolt circle 300 mm in diameter, and four 25-mm diameter aluminum bolts on a concentric bolt circle 200 mm in diameter. What torque can be applied without exceeding a shearing stress of 60 MPa in the steel and 40 MPa in the aluminum? Use G of ateel = 83 GPa and G for aluminum = 28 GPa. Express your final answer in N.m to the nearest whole number. Do not include the unit in your answe

A flanged bolt coupling consists of six 12-mm diameter steel bolts evenly spaced around a bolt circle 300 mm in diameter, and four 25-mm diameter aluminum bolts on a concentric bolt circle 200 mm in diameter. What torque can be applied without exceeding a shearing stress of 60 MPa in the steel and 40 MPa in the aluminum? Use G of ateel = 83 GPa and G for aluminum = 28 GPa. Express your final answer in N.m to the nearest whole number. Do not include the unit in your answe

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter1: Introduction

Section: Chapter Questions

Problem 1.5.6P: The data in Table 1.5.3 were obtained from a tensile test of a metal specimen with a rectangular...

See similar textbooks

Similar questions

A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bolt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter db / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gb = 28 Gpa.
A 2500 lb horizontal bar is supported by three 3/16-inch diameter wires as shown. The wires are symmetrically spaced and 20 feet long. The two outer wires are steel and the middle wire is brass. Calculate: a) Stresses in the wires
A steel rod of 30 mm diameter is inserted in a copper tube of external diameter 45 mm and an internal diameter of 37 mm carries a load of W =1750kN. The length of this compound bar is 180 mm. If, ES= 2 × 105 N/mm2and ECu= 1 × 105 N/mm2, calculate the stresses developed in copper and steel.
A rigid bar of weight W = 800 N hangs from three equally spaced vertical wires (length L =150 mm, spacing a = 50 mm): two of steel and one of aluminum. The wires also support a load P acting on the bar. The diameter of the steel wires is ds = 2 mm, and the diameter of the aluminum wire is da = 4 mm. Assume Es = 210 GPa and Ea = 70 GPa.(a) What load Pallow can be supported at the midpoint of the bar (x = a) if the allowable stress in the steel wires is 220 MPa and in the aluminum wire is 80 MPa? (See figure part a.)(b) What is Pallow if the load is positioned at x =a/2?(See figure part a.)(c) Repeat part (b) if the second and third wires are switched as shown in the figure part b.
A flanged bolt coupling consists of seven steel 20mmϕ bolts spaced evenly around a bolt circle 300mm in diameter. Determine the torque capacity of the coupling if the allowable shearing stress is 40MPa. See figure 13
A compound shaft consists of brass segment (1) and aluminum segment (2). Segment (1) is a solid brass shaft with an outside diameter of 0.51 in. and an allowable shear stress of 4500 psi. Segment (2) is a solid aluminum shaft with an outside diameter of 0.41 in. and an allowable shear stress of 6000 psi. Determine the magnitude of the largest torque TC that may be applied at C. Express your answer in lb-in rounded to the nearest tenths.
A flanged bolt coupling consist of 9 steel bolts evenly spaced around a bolt circle 300 mm. in diameter and 6 bronze bolts on a concentric bplt circle 200 mm. in diameter. What are the sizes of bolts diameters for steel and bronze, if the torque applied is 6,000 N-m and without exceeding the stress of 60 MPa in the steel and 40 MPa for the bronze? The ratio of the bolt diameter db / ds = 0.50. For steel, use Gs = 83 GPa and for bronze, Gb = 28 Gpa.
Answer all.a.A mild steel flat of width b= 150 mm, thickness t = 20 mm and length L= 6000 mm carries an axial pull P = 300 kN. If modulus of elasticity of mild steel is 200 GPa and Poisson’s ratio is 0.25, calculate the change in length, width and thickness of the flat. B.A stepped bar made of brass is subjected to axial loads as shown in the below figure. Determine the total change in length of the bar. Take E =100 GPa.figure is attached C.A thin cylinder of external diameter 820 mm, length 3 m and wall thickness of 10 mm is subjected to an internal pressure of 2.5 N/mm2 . Determine the change in diameter and length. Take Young’s modulus = 2×105 N/mm2 and Poisson’s ratio = 0.25.
A steel rod bar 250 mm long has a diameter of 10 mm and fits concentrically inside a bronze tube of the same length. The outside diameter of the bronze is 15 mm has a wall thickness of 2 mm. The r bar and the tube are connected by rigid end plates, so that they twist together. The composite shaft is designed to transmit 16 N.m torque. Take Gsteel=80 GPa and Gbronze=30 GPa. Calculate the torsional stiffness for each The torque transmitted by each shaft The maximum shear stress in each The angle of twist in degrees
The figure shows a single acting rivet connecting steel plates. Rivet diameter d = 22 mm,plate thicknesses are t1 = 20 mm, t2 = 12 mm, plate width b = 100 mm and e = 38 mm. The shear strength in the material is τem = 100 MPa, the safety stress in pressure and tension is σL = 280 MPa andSince σem = 140 MPa, determine the maximum force P that the joint can safely carry.
A 2-m long steel rod, 10-mm in diameter, is carrying a load of 20 kN. (a) what is the axial stress developed in the rod, in kN/m^2. Is the tensile or compressive? (b) compute the amount of elongation (in mm) in the steel rod caused by the applied load, (c) what will be the elongation (in mm) in the steel rod if the weight of the steel rod is included? Use density of the steel to be 7860 kg/m^3. Young's modulus of elasticity, E=200GPa. W=mg. Draw free body diagram of the steel rod.
A steel rod with a cross sectional area of 120〖mm〗^2 is stretched between two fixed points. The tensile load at 20°C is 4200N. What will be the stress at-25°C? α=11.7x〖10〗^(-6)/°C and E = 200GPa. See figure 06