A flanged bolt coupling consists of ten 20-mm diameter steel bolts spaced evenly around a bolt circle 400 mm in diameter. Determine the maximum shear stress formed in a 200-mm diameter shaft if the allowable shearing stress in the bolts is 40 MPa. Show complete solution and figure

A flanged bolt coupling consists of ten 20-mm diameter steel bolts spaced evenly around a bolt circle 400 mm in diameter. Determine the maximum shear stress formed in a 200-mm diameter shaft if the allowable shearing stress in the bolts is 40 MPa. Show complete solution and figure

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter5: Stresses In Beams (basic Topics)

Section: Chapter Questions

Problem 5.9.4P: A circular pole is subjected to linearly varying distributed force with maximum intensity t0....

See similar textbooks

Related questions

Q: An AISI 1010 steel pipe is used to transport chilled water from a chiller to a fan coils. The inner ...

Q: The flow between two horizontal infinite parallel plates is a two-dimension, steady-state, incompres...

Q: A shaft in torsion only is to transmit 2500 HP at 570 rpm with mild shock. Its material is AISI 1137...

Q: Consider a nuclear power plant operating on the ideal Rankine cycle with steam as the working fluid....

Q: At a temperature of 80°C, a steel tire 12 mm thick and 90 mm wide that is to be shrunk onto a locomo...

A: Given Data: Initial temperature, T1=80 C Final temperature, T2=25 C

Q: 1-For the figure below take M number of you and find the reactions? 2-ls the body equilibrium or not...

Q: E material has inner m'K, the temperatu

Q: in an absorption type refrigerator, the heat is supplied to NH, generator by condensing steam at I b...

A: Given:Evaporator temperature, Te=-5o C or 268 KCondensor temperature, Tc=27o C or 300 KSteam pressur...

Q: The displacements in an elastic material are given by: M(1 – v²) M(1 + v)v M(1 – v?) U1 = - -X1X2; U...

A: Three disqusional strain rel atmosphere∈xx=∂y∂x, Eyy=∂Y∂y, ∈22=∂ω∂z

Q: 1-For the figure below take M number of you and find the reactions? 2-ls the body equilibrium or not...

Q: A 1-lb collar is attached to a spring and slides without friction along a circular rod in a vertical...

Q: The magnitude of the load

A: Given; A horizontal plate has been joined to a vertical to a vertical post using four rivets arrange...

Q: P5.2 A rectangular bar of length L has a slot in the central half of its length, as shown in Figure ...

Q: Two cars A and B start travelling at different times. Car A travelled 2 hours ahead of car B. Initia...

Q: 5. A heat engine release heat into the cold reservoir at 500 K with a carnot efficiency of 25 %. Wha...

A: The exhaust temperature of 266.66 K is needed for 60% Carnot efficiency.

Q: During nominal operation, the power plant operates with the following parameters. Wpump,in = 4.05 kJ...

Q: nsions shown is hinged at its top at A. The gate rests on a frictionless surface at B. a. Determine...

A: given:

Q: Air (ρ = 1.23 kg m−3 ) leaving a 3-cm-diameter pipe strikes a plate that can rotate about a pivot. T...

Q: efrigerator is -5°C. The temperature of the atmosphere is 27°C. Find max. COP of the refrigerator. I...

Q: In the figure below, two forces are acting at the same point A. Find the resultant of these two forc...

Q: A closed tank whose bottom is 18 inches in diameter is filled with three liquids: 12 inches of carbo...

Q: Robotic Hand, search at least two of any related machine that applies the said technology and in fi...

A: robotic hand is one of the most versatile tools used in todays industry

Q: Problems: Determine the standard differential equation of the figure below. a. Using movement of blo...

Q: A1/ For the shape below, the Resultant of three forces (200N, F1 and F2) is 600N: (a) the force F1 i...

Q: A Cold Store maintains a storage temperature minus 23°c in an ambient of 27°c. he pleent is fittes w...

Q: work output from the

A: Given; An engine operates on the reversible cycles as shown in the figure.Find work output from the ...

Q: The cylinder of a four stroke diesel engine has the followin, specifications: Cylinder bore :150 mm ...

A: Cylinder bore D=150 mm Maximum pressure =3.5mPa=3.5N/mm2 Cylinder Material = Grey Cast Iron FG200 Su...

Q: 1-For the figure below take M number of you and find the reactions? 2-ls the body balanced or not? 3...

Q: Air at free-stream velocity of 9 m/s flows over a thin flat plate of length 3 m and width 1.5 m. A l...

Q: ned using sin aness is measu 1

Q: 2-119. A force of F ={-40k} lb acts at the end of the pipe. Determine the magnitudes of the componen...

Q: vapour leaves the evap

Q: C3/(a) For the figure below take M number of you and find the reactions * ? 3 m 3 m 3 m E C 12 M 13 ...

Q: C3/(a) For the figure below take M number of you and find the reactions ? * + 3m 3 m 3 m 12 M- 52. 5...

Q: m°C) having 1

Q: Q2:Replace the Force 70N by Equivalent System consist of one force &couple at 1: At Supporting point...

A: Given,

Q: Q7. What is the stress concentration for shear stress due to torsion at the critical location? (Sele...

Q: Part a) Determine the power in hp delivered by the motor when the elevator is moving down at a const...

Q: The collar of mass m is released from rest while in position A and subsequently travels with negligi...

Q: The instrument of mass 50 kg is meant for impact on a surface. The impact velocity 10m/sec. Inside t...

A: Given data as per question mass=50 kgx0=vo=10 msk=5 Nmc=1 NsmMaximum dispalcement of instrument afte...

Q: 1) Material properties labelled A, B, C and D 2) How do you detemine the material's Young's modulus?...

A: Q1 - A- Proportional Limit B- Elastic Limit C- Ultimate Stress D- Fracture point Q2- Young's Modulus...

Q: principal stress is 10 kPa, then the normal stress The state of stress at a point, for a body in pla...

Q: Cars arrive at a service station according to Poisson's distribution with mean rate of 5 per hour. T...

A: Given:mean rate, λ=5 /hrservice time per car=10 minservice rate, μ=6010=6 / hr

Q: What’s the answer for this please ?

A: Option d is correct . Regeneration :- this is done by preheating the compressed air before entering...

Q: The expected life of a ball bearing subjected to a load of 8800N and working at 1000rpm is 1000hours...

Q: Determine if it is one dimensional heat transfer or steady heat transfer then why?. Baseplate of a ...

A: For a baseplate of a cloth iron subjected to uniform heat flux, the temperature does not vary at a p...

Q: W= 75 Ib W= 150 lb W= 75 Ib R.

Q: An aluminum fin (k=237W/ m°C) having I cm diameter with 50cm length is attached to a combustion cyli...

Q: 13.44 A steel ball is released from rest in a container of oil. Its downward acceleration is a = 0.9...

Q: below, the reaction at E

A: given:

Question

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A shaft is made of an aluminum alloy having allowable shear stress of tallow = 100 MPa. If the diameter of the shaft is 100 mm, determine the maximum torque T that can be transmitted. What would be the maximum torque T if a 75-mm-diameter hole were bored through the shaft? Sketchthe shear-stress distribution along a radial line in each case.
A solid steel shaft will not twist through more than 3 degrees in a 6-m length when subjected to atorque of 12 KN"m. The modulus of rigidity of the steel shaft is 83 GPa. Determine;a) Diameter of the shaft.and Maximum shearing stress developed in the shaft.
A flange-and-bolt coupling between two shafts carries 12 bolts at a pitch diameter of 18 in. The shafts carry a torque of 50,000 ft-lb. Assuming that this torque is transmitted by shear across the 12 bolts and that these bolts are to be designed for a shear stress s3 = 3,000 lb/sq in., what is the bolt diameter?
A solid circular shaft with a 2-in diameter is subjected to a vertical shearing force of V= 4 kips. What is the approximate value of maximum shear stress on the shaft? (Select the nearest value) (a) 1700 psi (b) 1400 psi (c) 1000 psi (d) 700 psi
A hollow steel (G = 12,000 ksi) shaft has diameters of 6 in. and 4 in. and an allowable shearing stress of 9,000 psi. Determine the required number of 3⁄4-in diameter bolts for a flange coupling in which two-thirds of the bolts are on a 12-in diameter bolt circle and one-third are on a 9-in diameter circle. The allowable shearing stress in the bolts is 12,000 psi.
A flange bolt coupling is used to connect a solid shaft 90 mm in diameter to a hollow shaft 100 mm in outside diameter and 90 mm in inside diameter. If the allowable shearing stress in the shafts and the bolts is 60 MN/m2, how many 10-mm diameter steel bolts must be used on a 200-mm diameter bolt circle so that the coupling will be as strong as the weaker shaft?
Calculate the torque T: i. if the shear stress of the brass sleeve in section AB is limited to τb = 70 MPa.ii. if the shear stress of the steel shaft in section BC is limited to τs = 110 MPa.
When subject to an applied torque,a circular shaft of length 600mm twists through an angle of 2°,if the shear modulus for the shaft material is 80KN/m^2, calculate the shear stress; A)At the center of the shaft B)At a radius of 20mm C)if the maximum shear in the shaft is 120MN/m^2, calculate the outside diameter
A steel marine propeller shaft 13 inches in diameter and 15 ft long is used to transmit 9,426 hp at 189 rpm. if G = 12 x 10^6 psi, determine the maximum shearing stress in psi.
A flanged bolt coupling is used to connect a solid shaft 94 mm in diameter to a hollow shaft 100 mm in outside and 94 mm in inside diameter. If the allowable shearing stress in the shafts and the bolts is 63 MPa, how many 10-mm-diameter steel bolts must be used on a 190-mm- diameter bolt circle coupling so that the coupling will be as strong as the weaker shaft?
A steel shaft is used to transmit 37 kW at a speed of 1500 rpm. If the allowable shearing stress based on pure torsion is 41 MPa, determine the torsional deflection of the shaft in degrees per meter. Use G = 12 million psi.
n figure as shown below, assume that a 35mm diameter rivet joint the plates which are each 150mm wide.(a) if the allowable stresses 200 MPa for bearing in the plate material and 120MPa for shearing of the rivet, determine the minimum thickness of each plate.(b)Under the conditions specified in part (a) what is the largest average stress in the plate.