6 m6 mElbow6 m3 m.Activate WindGoto Sectines115 mA fluid is pumped at a rate of 0.00156 m/s through a 0.025-m-diameter pipe to fill a9°C020 k-15 mA fluid is pumped at a rate of 0.00156 m/s through a 0.025-m-diameter pipe to fill awater tank as shown in Figure. What is the pressure drop between the inlet (section1) and the outlet (section 2) accounting for all losses?The density of the fluid is (1.05x10^3) kg/m and the dynamic viscosityis 1.12 x 10 Ns/m2. The following are also known KL. elbow = 1.5, KL. exit1 and%3D!!surface roughness, e = 0.001 mm. Also take gravity, g =10 m/s?.The elbows are enlarged for ease of visualisation and the lengths shown are those ofthe pipes.Answer should be in Pa with three significant figures.Note: Your answer is assumed to be reduced to the highest power possible.Your Answer:ActivaGoto Sx109°CS.W2020

Answered: Image /qna-images/answer/930a1b83-6077-4575-aa44-11225be574ec.jpg

A fluid is pumped at a rate of 0.00156 m /s through a 0.025-m-diameter pipe to fill a water tank as shown in Figure. What is the pressure drop between the inlet (section 1) and the outlet (section 2) accounting for all losses? The density of the fluid is (1.05x10^3) kg/m3 and the dynamic viscosity is 1.12 x 10 - Ns/m2. The following are also known KL. elbow = 1.5, KL. exit = 1 and surface roughness, e = 0.001 mm. Also take gravity, g = 10 m/s. %3D The elbows are enlarged for ease of visualisation and the lengths shown are those of the pipes. Answer should be in Pa with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible.

A fluid is pumped at a rate of 0.00156 m /s through a 0.025-m-diameter pipe to fill a water tank as shown in Figure. What is the pressure drop between the inlet (section 1) and the outlet (section 2) accounting for all losses? The density of the fluid is (1.05x10^3) kg/m3 and the dynamic viscosity is 1.12 x 10 - Ns/m2. The following are also known KL. elbow = 1.5, KL. exit = 1 and surface roughness, e = 0.001 mm. Also take gravity, g = 10 m/s. %3D The elbows are enlarged for ease of visualisation and the lengths shown are those of the pipes. Answer should be in Pa with three significant figures. Note: Your answer is assumed to be reduced to the highest power possible.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water flows thru a 20mm-dia pipe at a rate of 0.19lps supplying a shower head. The shower head has 100 holes and maintains a velocity of 2.419155m/s per hole during normal usage. Determine the diameter of each hole in the shower head.
Calculate the water power available in the pipe flowing at the rate of 0.166 m3/s with total Head as 29.9 m. 48691.0 W 5.0 W 4963.4 W 48.7 W
[CE Hydraulics] Is the flow expected to be uniform or nonuniform for frictionless pipes? Why?
Can you use the friction factor for turbulent flow in a smooth circular tube to predict the fiction factor in an internally finned tube by using the hydraulic diameter?
Calculate the head loss due to friction in a pipe of diameter 25 cm and length 60 m, through whichwater is flowing at a velocity of 2 m/s. (a.) Darcy formula (b.) Chezy’s formula for which C = 60.
include a free body diagram Seawater is to be pumped into a large tank at a rate of 165 kg/min. The tank is opwn to atmostsphere and the water enters the tank from a 80 m height. The overall efficiency of the motor pump unit is 75 percent and the motor consumes electricity at a rate of 3.2 KW. If the irreversible headloss in the piping is 7 m, the velocity of the water (in m/s) at the tank inlet isA. 6.21B. 7.12C. 8.7D. 5.05
The water is flowing througha pipe having diameters 20 cm and 10 cm at sections 1and 2 respectively. The rate of flow through pipe is 0.035 m /s. The section1 is 7500 mm above datunm and section 2i5 500 cm above datum. If the pressure at section 1 is 420 kPa, find the intensity of pressure at section 2.
Two pipes, one circular and one square have the same cross-sectional area. Which has the larger hydraulic radius ? Show your solution to prove your answer
A pipeline transporting engine oil of 3.5 m3/s at 40⁰C branches out into two parallel pipes made of commercial steel but reconnects downstream. Pipe A is 750 m long and has a diameter of 50 cm while Pipe B is 1200 m long with a diameter of 50 cm. Neglecting minor losses, determine the following:a) Flow rates (in m3/s) through pipe A and pipe B.(Hint: Assume similar flow frictional factor for initial calculations and determine the correct frictional factor using Colebrook equation).b) Actual head losses (in m) in pipe A and pipe B
Water (ρ=998 kg/m³, μ=1.02x10^-3 kg/ms) flows through a 598 m length of pipe with 150 mm in diameter at 60 L/s. Determine the pipe roughness, ɛ if the head loss is 49 m.
Water at 10oC is to flow from reservoir A to reservoir B through a cast-iron pipe of length 20 m at a rate of Q=0.0015 m3/s as shown in Figure. The system contains a sharp-edged entrance and six regular threaded 90° elbows. Determine the pipe diameter needed.
Water is pumped from a reservoir to a pressurized storage tank (P = 150 kPa gauge) atop a building by means of a centrifugal pump. There is a 70-m difference in elevation between the water surface in the reservoir and the end of the discharge line. The piping system consists of 80m of 5" SCH 40 steel pipe containing two 90o elbows, one gate valve, one rotary water meter, and six couplings from the reservoir to the pump; 3" SCH 40 steel pipe for 86m to the tank. The 3" pipe contains two gate valves, four 90o elbows, and ten couplings. It is desired to maintain a flow of water into the tank of 2.4 m3/min. Water temperature is 25oC. If the pump-motor set has efficiency of 65%, what would be the pumping costs be in pesos per day if electricity costs PhP 10.50/kW-hr?