A Flyback converter (for questions 1-3) shown below has the following parameters. Vin=100V, Vo=20v,Po=40W, D=0.25, Fsw=250kHziini outin1. What is the turns ratio N1:N2 between the primary side winding and the secondary side winding?A. Ν1: N25:3B. N1: N2 = 3:5C. N1: N2= 5:2D. None of the above%3D2. What is the maximum voltage on the power switch?A. 120VВ. 133VС. 100VD. None of the above3. What is the maximum voltage on the diode?Α. 40VВ. 133VC. 80VD. None of the above4. The magnetizing inductor at the primary side winding is 100uH, what is the peak current in the powerswitch?Α. 1.8ΑВ. 1.6AС. 2.1AD. None of the above

Note: As per our policy, I have attempted the first three questions. Given data: Vin=100 VVo=20…

A Flyback converter (for questions 1-3) shown below has the following parameters. Vin=100V, Vo=20V, Po=40W, D=0.25, Fsw=250kHz in iout 1. What is the turns ratio N1:N2 between the primary side winding and the secondary side winding? A. N1: N2 = 5: 3 B. N1: N2 = 3:5 C. N1: N2= 5:2 D. None of the above 2. What is the maximum voltage on the power switch? A. 120V В. 133V C. 100V D. None of the above 3. What is the maximum voltage on the diode? A. 40V В. 133V С. 80V D. None of the above 4. The magnetizing inductor at the primary side winding is 100uH, what is the peak current in the power switch? A. 1.8Α В. 1.6A С. 2.1A D. None of the above

A Flyback converter (for questions 1-3) shown below has the following parameters. Vin=100V, Vo=20V, Po=40W, D=0.25, Fsw=250kHz in iout 1. What is the turns ratio N1:N2 between the primary side winding and the secondary side winding? A. N1: N2 = 5: 3 B. N1: N2 = 3:5 C. N1: N2= 5:2 D. None of the above 2. What is the maximum voltage on the power switch? A. 120V В. 133V C. 100V D. None of the above 3. What is the maximum voltage on the diode? A. 40V В. 133V С. 80V D. None of the above 4. The magnetizing inductor at the primary side winding is 100uH, what is the peak current in the power switch? A. 1.8Α В. 1.6A С. 2.1A D. None of the above

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter12: Power System Controls

Section: Chapter Questions

Problem 12.4P

See similar textbooks

Similar questions

A freewheeling DC motor is driven with 1000 rpm and a nominal load torque of 80Nm. The field circuit resistance is 200 and the armature circuit resistance is 0.2 O. The field coils are fed with a zero degree transmission angle through a single-phase fully controlled converter connected to a single-phase 240V source. The armature circuit is fed from a single phase 400V source through another fully controlled converter. Magnetic saturation has been neglected, the motor constant is given as 0.8 V - s / A - rad. Assuming that there is no fluctuation in armature and field current, find the control angle of the converter feeding the armature at nominal load. If you want to leave the question blank, click again on the option you marked.
. The stray load loss of a wound rotor induction motor can be determined byA. applying a predetermined current to the stator and subtracting the I²R loss from the input power.B. exciting the rotor with a-c voltage and driving it at synchronous speed in the opposite direction.C. driving the rotor in the normal direction by an external power source.D. measuring the total losses and adding the other losses. Note: I have doubts if it is the letter A or the letter C, can you help me in this question, thanks.
A four-pole induction motor drives a load at 2500 rpm. This is to be accomplished by using an electronic converter to convert a 400-V dc source into a set of three-phase ac voltages. Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2 hp. If the dc-to-ac converter has a power efficiency of 88 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source.
5a) With the aid of power-load angle curves explain in detail the following: an electronic governor’s response to frequency changes resulting from changing loads. b) A circuit breaker’s response when a transient fault occurs c). the response of an automatic voltage regulator to voltage dip as the result of the start-up of a high rated induction motor.
A four-pole induction motor drives a load at 2405 rpm. This is to be accomplished by using an electronic converter to convert a 400V dc source into a set of three-phase ac voltages. a) Find the frequency required for the ac voltages assuming that the slip is 4 percent. The load requires 2hp. b) If the dc-to-ac converter has a power efficiency of 93 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the dc source.
A 3,000-kw 750-volt d-c 60-cycle six-phase synchronous converter is fed from a three-phase 23,000-volt high-voltage line through &bank of three transformers that are connected in Δ on the high side and diametrical on the low side. (A) Make a winding diagram showing all connections for the problem. Assuming an efficiency and power factor of 96percent and 0.95, respectively, calculate: (B) the direct-current output; (C) the a-c voltage between adjacent slip rings.
Q5:- Adjust a fire angle for a three-phase fullwave semi-controlled converter to feed the separately exciter DC motor to get a load torque that can be reached to 730 rpm. When the supply voltage of converter is 160 volts per-phase and the absorbed current through the armature 40A with resistance 0.2 and a constant back emf 0.4v/rpm. Then find the maximum speed for motor assume the previous parameters values are a constant.
25.a. The stray load loss of a wound rotor induction motor can be determined byA. applying a predetermined current to the stator and subtracting the I²R loss from the input power.B. exciting the rotor with a-c voltage and driving it at synchronous speed in the opposite direction.C. driving the rotor in the normal direction by an external power source.D. measuring the total losses and adding the other losses.25.b. Excitation losses in a transformer must be determined. When running the test, you should make surethat the secondary windingA. is short-circuitedB. carries exactly the rated current.C. is open-circuited.D. carries a higher current than the primary
1-why the slipoccur in the induction motor? 2- why the slip is less than 1? 3-what the adrantage of study the slip in the induction motor?
Single phase half wave AC-AC converter has a resistance of R = 50 ohms. Input voltage is given as 230 Vrms. Transformer conversion ratio is 1:1. If T1 thyristor is triggered at 60 degrees; a)Rms output voltage? b)Output power? c)RMS load current and average load current? d)Input power factor? e)Average and RMS thyristor current?
Define the working of the Three phase induction motor with the properly labelled diagrams
A 4-pole induction motor drives a load at 2500 rpm. This is to be accomplished by using an electronic converter to convert 400 Volts DC into a set of 3-phase AC voltages. Find the frequency required for the AC voltages assuming that the slip is 4 percent. The load requires 2 hp. If the DC-to-AC converter has a power efficiency of 88 percent and the motor has a power efficiency of 80 percent, estimate the current taken from the DC source.