A four stage Marx multistage impulse generator has 0.1 micro Farad capacitors in each stage. The wave front and wave tail resistances are 20 Ohm and 800 Ohm respectively. If the load capacitance is 1 micro Farad, What will be the values of following quantities? Wave tail time Generator capacitance Wave front time

A four stage Marx multistage impulse generator has 0.1 micro Farad capacitors in each stage. The wave front and wave tail resistances are 20 Ohm and 800 Ohm respectively. If the load capacitance is 1 micro Farad, What will be the values of following quantities? Wave tail time Generator capacitance Wave front time

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter7: Alternating Current, Power Distribution, And Voltage Systems

Section: Chapter Questions

Problem 7RQ

See similar textbooks

Similar questions

QUESTION 3 An inductor, a capacitor, and a resistor are connected in parallel with a function generator. The inductor draws 100mA RMS, the capacitor draws 150mA RMS, and the resistor draws 200mA RMS. Find the magnitude of the total current. O 450mA RMS O 544mA RMS O 352mA RMS O 206mA RMS
6. What is the effect of load inductance on the ripple current? 7. i effect of chonnine Bock and boost 8. Wh 9 What chopping 10. At what duty evcle does the load current rinnle current he
what is the reactive power absorbed by the load ZL in VAR? Assume source is in rms
When a capacitor is discharged through a resistor, the discharge curve is exponential Sinusoidal Step Square
Shown in the figure below is an "RC" circuit drive by an AC power source. The AC power source has an RMS voltage of Vps (RMS) = 11.58 Volts and is running at a frequency of f = 1.326e+04 Hz. resistor has a resistance of R = 3750 2 and the capacitor has an capacitance of C = 3.17e-09 Farads. Vps R ww Write the FORMULA for the total impedance of the circuit Ztot = Write the FORMULA for the phase of the total impedance of the circuit tot = Determine the numerical value of Ztot = Determine the numerical value of Pztot= Determine the current through the circuit: • I(PEAK) = • I(RMS) = Determine the voltage across the resistor: Amps Amps S2 C degrees
Protection Schemes for Series Capacitor (compensation )
C. Draw a general sine wave V vs t and I vs t plot for a purely resistive and a purely inductive circuit and show leading lagging parameters and clearly mark the phase difference.
the location of Series capacitor bank compensation for power factor improvement
A resistor, a capacitor, and an inductor are connected in series with a function generator. The resistor has a resistance of 10Ω, the inductor has a reactance of 14Ω, and the capacitor has a reactance of 5Ω. The circuit has a total current of 1.5A RMS. Find the total voltage.
QUESTION 4 A resistor, a capacitor, and an inductor are connected in series with a function generator. The resistor has a resistance of 1.5k2, the inductor has a reactance of 1.2kQ, and the capacitor has a reactance of 2002. The circuit has a total current of 172mA RMS. Find the total voltage. O 310V233.7 O 74.5VL-14° 188V273.2 O 44.4VL-25.3°
A elearning.adpoly.ac.ae * Question Completion Status: QUESTION 16 E-06, PC-02. Three inductors 15 mH, 15 mH and 15 mH are connected in parallel. What is the total inductance? O Without knowing the coupling factor the total inductance cannot be found. O 45mH. O5 mH. QUESTION 17 E-06, PC-04. The time constant in an inductive circuit is the time required for the current to reach? O 70.7% of maximum value. O 63,7% of maximum value. O 63,2% of maximum value. QUESTION 18 E-06, PC-01. When more than two inductors of different inductance are connected in parallel in a circuit, the total inductance is? O Less than the inductance of the lowest rated inductor. O Equal to the sum of the individual inductance. O Equal to the inductance of the highest rated inductor. QUESTION 19 E-06, PC-02, Three inductors 15 mH, 15 mH and 15 mH are connected in series, What is the total inductance? Click Saue and Submit to save and submit. Click Save All Answers to save all answers.
15. You are working on a power factor correction installation, and you notice with a clip-on ammeter as you add in capacitance the current drops, you add more capacitance and the current drops, you add more capacitance the current rises. How do you know when you are at unity power factor?