A frame has dimensions and loadings as shown in the figure and parameter table. Determine the horizontal and vertical support reactions that the pins exert on the frame at A and C. Take postive directions to be to the right, and up. cc 00 2021 Cathy Zupke parameter Force A Force Ay= Force C₂ = Force Cy= = W L₁ L₂ A value -L₂- units 1 kN/m 3 4.5 m m 3 3 3 3 KN KN KN KN C B W

A frame has dimensions and loadings as shown in the figure and parameter table. Determine the horizontal and vertical support reactions that the pins exert on the frame at A and C. Take postive directions to be to the right, and up. cc 00 2021 Cathy Zupke parameter Force A Force Ay= Force C₂ = Force Cy= = W L₁ L₂ A value -L₂- units 1 kN/m 3 4.5 m m 3 3 3 3 KN KN KN KN C B W

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

length=7m height=250mm UDL on the beam=38.5KN/M d=812mm Mass of the beam=65.9kg/m a. Consider design loads( udl+self weight) b. Calculate and draw the Bending Moment Diagram (BDM).What is the value of the maximum bending moment? c. Calculate and draw the Shear Force Diagram (SFD).What is the value of the maximum shear force? d. Using the table, calculate the maximumdeflection of the beam.
Calculate the vertical deflection of point B and the horizontal movement at D shown in the figure. Consider that all the elements of the truss are linearly elastic and have sectional areas of 1800mm2. Also consider an E of 200,000N/mm2. Add the calculation process of solving the problem step by step and complete the table accordingly. L F FB ∂FB / ∂PB FD ∂FD/∂PD AE - 2√2/3 PB -2/3 √2 EB EF AB BC CD BF FD FC
Consider the frame shown in figure. Suppose that P1 = 5.5 k and P2 = 11 k. Each column has the cross-sectional area indicated. Solve the problem using the cantilever method of analysis. Assume that the internal moment, shear, and normal force in the vertical beam are positive if they act as shown. a) Determine (approximately) the normal force at A. NA = _____ k Submitted Answers ANSWER 1: Deduction: -3% NA = 4.973 k ANSWER 2: Deduction: -3% NA = 3.8254 k ANSWER 3: Deduction: -3% NA = 5.933 k
Two spheres, each 1.20 m in diameter, weighs 4 kN and 12 kN respectively. They are connected with a short rope and palced in water. Find the tension in the rope in kN. CHOICES: a.2.15 b.3.12 c.3.87 d.4.45
A 900 N-m couple is applied to the flywheel in the diagram. The minimum force X required to prevent rotation of the flywheel is also applied. If the coefficient of belt friction is 0.20, a. which tension is larger, TA or TB?Explain b. What is the angle of contact in radians? c. What is the value of the ratio TA/TB?
A rod 3.5 feet long rotates in a horizontal plane about a vertical axis through its center. At each end of the rod is fastened a cord 6 ft. long. Each cord is inclined at Ø = 450 with the vertical and supports a weight of 45 lbsA. Which of the following gives the speed of rotation “n” in rpm?a) n = 25.12 rpm b) n = 25.12 rpm c) n = 30.20 rpmd) n = 22.13 rpm B. What is the tension in the 5 feet long cord? a) T = 58.47 lbb) T = 63.63 lbc) T = 51.78 lb d) T = 48.25 lb
A cantilever beam 3 m long carries a uniformly varying load zero at fixed to 1200 N/m at free end. Assume that E = 10 GPa and I = 30 x 10x10⁶ mm⁴. 1. Which of the following most nearly gives the deflection at free end? a. 21.4 mm b. 29.7 mm c. 38.1 mm d. 18.5 mm 2. Which of the following gives the deflection at a section 2 m from fixed end? a. 10.5 mm b. 20.3 mm c. 16.4 mm d. 14.8 mm 3. Which of the following gives the rotation at a section 2 m from fixed end? a. 0.421° b. 0.914° c. 0.739° d. 0.614°
A cantilever beam with a lumped mass W is constrained by a spring and a viscous dashpot damped, as shown in figure 3 below. If L= 60 in, EI= 10^3 lb-in^2 , c= 20 lb-s/in , W= 2000 lbs, k= 2kips/in, u0 = 0.5in, u0 (u with the dot in the middle up) = 10 in/s , determine (1) the displacement at t= 1.5 seconds, u( t=1.5) , and (2) the velocity at t= 1.5 seconds, u(t= 1.5) (u with a dot up in the middle again).
The frame given in the figureR = 0.25m radius at point Ea frictionless reelare available. Support reactions andall joint forcescalculate. (W = 200 kN)
The following are the properties of a steel section to be used for a column element that is pinned at the bottom and fixed at the top.Fy = 248 MPa Ix = 3.00E+08Area = 21300 Iy = 9.90E+07Sx = 2076124.567 d = 289Sy = 685121.1073 tw = 19.2tf = 31.8 bf = 265w beam in kg/m = 918 L = 3 m 1. What is the Euler’s allowable axial stress? a. 2080.40MPa b. 701.23MPa c. 3003.60MPa d. 816.67MPa 2. What is the allowable axial stress as per NSCP 2001? a. 117.18 MPa b. 121.23MPa c. 103.60 MPa d. 136.99MPa 3. Find the maximum axial load that includes self weight of the section that it can carry if only axial load is present. a. 2918 kN b. 701.23 kN c. 1003 kN d. 716.67 kN
The frame shown in the figure is supported by a hinge at E and roller at D. Compute the horizontal and vertical component of the hinge force at C. as it acts upon BD *use 3 decimal place in rounding off all throughout the solution.
A beam is subjected to uniform force w as shown in the figure below, E of the entire section is 30000 kips/inch^2, I is 240 in^4, if point A is supported by 0.003 rad clockwise before assembly, and point B is supported at Subside 0.3 inches before assembly, try to calculate the reaction force of point A and point B.