A full wave rectifier supplies power to a 2kilo ohm load. The AC voltage applied to the diode is 250V(RMS) a center tap transformer was used. If The diode resistance is 40 ohms and that the diode has a threshold voltage of 0.7 Volts. Determine a. Draw the Schematic diagram and waveform of the rectifier b. Determine the average load current b. The average load voltage c. Rectification efficiency= Po/Pix 100% or lDc²X R₁/IRMSO²(Rd+R₁)

A full wave rectifier supplies power to a 2kilo ohm load. The AC voltage applied to the diode is 250V(RMS) a center tap transformer was used. If The diode resistance is 40 ohms and that the diode has a threshold voltage of 0.7 Volts. Determine a. Draw the Schematic diagram and waveform of the rectifier b. Determine the average load current b. The average load voltage c. Rectification efficiency= Po/Pix 100% or lDc²X R₁/IRMSO²(Rd+R₁)

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 4RQ: What is the difference between a diode and rectifier?

See similar textbooks

Similar questions

A 3.3-V, 30-A dc power supply is to be designed with a ripple of less than1.5percent. Assume that a half-wave rectiﬁer circuit (60 Hz) with a capacitor ﬁlter is used. (a) What is the size of the ﬁlter capacitor C? (b)What is the PIV rating for the diode? (c)What is the rms value of the transformer voltage needed for the rectiﬁer?(d) What is the value of the peak repetitive diode current in the diode? (e) What is the surge current at t =0+?
The half-wave rectiﬁer as shown is operating at a frequency of 60Hz, and the rms value of the transformer output voltage vI is 12.6V±10%. What are the nominal and worst case values of the dc output voltage VO if the diode voltage drop is 1V?
The full-wave rectiﬁer ias shown is operating at a frequency of 60 Hz, and the rms value of the transformer output voltage is 18 V. (a) What is the value of the dc output voltage if the diode voltage drop is 1 V? (b) What is the minimum value of C required to maintain the ripple voltage to less than 0.25 V if R = 0.5 Ω? (c) What is the PIV rating of the diode in this circuit? (d) What is the surge current when power is ﬁrst applied? (e) What is the amplitude of the repetitive current in the diode?
Determine the peak output voltage for the bridge rectifier in this figure. Assuming the practical model, what PIV rating is required for the diode? The transformer is specified to have a 12 Vrms secondary voltage for the standard 110 V across the primary.
A 2500-V, 2-A, dc power supply is to be designed with a ripple voltage ≤ 0.5 percent. Assume that a half-wave rectiﬁer circuit (60 Hz) with a capacitor ﬁlter is used. (a) What is the size of the ﬁlter capacitor C? (b) What is the minimum PIV rating for the diode? (c) What is the rms value of the transformer voltage needed for the rectiﬁer? (d) What is the peak value of the repetitive current in the diode? (e) What is the surge current at t =0+?
A 24-V secondary of a transformer is connected to a half-wave rectifier and a 50 ohms load device. Calculate the DC output voltage Calculate the average current Which rectifier diode would be adequate for this application?
what is the purpose of installing a filter capacitor in a bridge rectifier circuit? Why don't we install a zener diode which reduces the ripple voltage or to get a consistent voltage wave at Vout?
Define peak inverse voltage (PIV)? And write its value for Full-wave rectifier?
A voltmeter measures an AC voltage of 150 V. a) What is the peak voltage? What is the RMS voltage? b) If a full wave rectifier is being used to convert it to DC, what is the level of DC voltage? 'c) If this voltage source is applied to a 25 Ω resistor, what is the dissipated power by the resistor?
How do you define the output voltage ripple in a rectifier circuit? Suggest a method to reduce theoutput voltage ripple.
In a center-tapped full wave rectifier circuit utilizing ideal diodes, if the primary voltage is 160Vpeak, the turns ratio is 8:1 and the load resistance is 860 ohms, what is the rectified dc voltage at the output? express answer in volts
) Determine the reading obtained withaDC voltmeter at RB when the switch is set at point B. b) Determine the reading at thesame RBusing ½ wave and Full wave rectifier AC meter respectively when the switch is set at point A. Given that Ifs = 100-µA and set at 10-V dc or rms range.