A fully-restrained beam with span length of 10 meters was designed using ASTM A36 steel (Fy = 250 MPa) rolled as W16x57 section. Lateral bracing was only provided on the supports and on third points. The said beam is to be subjected to a super-imposed uniformly distributed dead load of 5.00 kN/m and a total uniformly distributed live load of 20.00 kN/m. The only deflection limit imposed for the design of the said structure is that its deflection at midspan due to total service loads should not exceed its span length divided by 150. Assess if the designed section for the beam is adequate for its purpose. Consider flexure, shear, and the imposed deflection limit. Use ASD specifications. Assume unstiffened webs.

A fully-restrained beam with span length of 10 meters was designed using ASTM A36 steel (Fy = 250 MPa) rolled as W16x57 section. Lateral bracing was only provided on the supports and on third points. The said beam is to be subjected to a super-imposed uniformly distributed dead load of 5.00 kN/m and a total uniformly distributed live load of 20.00 kN/m. The only deflection limit imposed for the design of the said structure is that its deflection at midspan due to total service loads should not exceed its span length divided by 150. Assess if the designed section for the beam is adequate for its purpose. Consider flexure, shear, and the imposed deflection limit. Use ASD specifications. Assume unstiffened webs.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

S f A structure is to be built as shown supporting a uniform load of 18 kN/m. The location for the supports at A and B has been determined. The connection at C may be placed anywhere along the member AD 18 kN/m A C D 3 m B L -7 mi -5 m- If the allowable bending stress for member AD is 8 MPa, which among the choices gives the most economic section? Select the correct response: 275 mm x 550 mm 250 mm x 500 mm 300mm x 600 mm 225 mm x 450 mm rigid
Total load 87 psf = B1W16 x 57 G1W24 x 68 Compute Vmax and Mmax for Beam 1 and Girder 1 in the roof framing plan. 28' H I H- B1 6 @ 6' = 36' B1 B1 B1 B1 | G1 I- I-
Example 3 AT-shaped simply supported beam has the crass Section shown in Figure PL.4, It has a span of 36 t (11 m), is loaded with a gravity live-load unit intensily W, - 2,500 plt (365 kN), and is prestressed with twelve 1-in,-dia (Iweive 12.7-mm-dia) seven-wire stress-relieved strands. Compute the con- crete fiber stresses at service load le- 34 3 Mpa lei- 25 MPa e- 244 nn 1138 MPa The section properties: 25.4mm -MPa r-ly Ac- mm2 CA JI3.722 NT. 763 mm S- 4.885 ot 7 mn S 3.456e+7 rvr. Wp- 7.662 kN. (Including s.w) Hy- 36.5 kN/m Aps= 12 12.7 mwn (7 wire strands) (Answer: 10.5 MPa. 0.36MPa, 762mm 609 6 mm
A built up section of A992 steel, F, = 345 mPa is made from plates fully welded together. The flanges consist of PL16X380 and PL12X500 for the web. Use the NSCP 2015 specifications. PL16x380 WL = 1.5wp %3D A Wu = 3.6wp 10m Which of the following best gives the maximum service dead load, wp? 40.2 kN/m 26.8 kN/m O 10.8 kN/m O 96.6 kN/m PL12x500
a om long simply supported beam has a width of 350mm and overall depth of 470mm the beam is reinforced with 2- 28mm compression bars and 4-28mm bension bars each located 70mm from the extreme concrete fber. concrete strength is 21 Mpa and yield strength is 420Mpa determine the ff. depth of compression block ultimate moment capacity of the beam derermine the addinonal concentrated ive load that can be acpled at midspan if the dead load inclusing the weight if the beam is 20KN m Select the corect response a- 82.79mm, Mu- 320 SSKN-m, Pu Ba57KN a- 165.58mm, Mu - 328 13KNm, Pu -136 88KN O a 110.81mm, Mu - 351 47KNm, Pu 15o.09KN O a- 110.81mm, Mu 316 23KNM, Pu - 86 BKN a- 82 79mm, Mu- 320 5SKNm Pu1537KN a 165 semm, Mu 295 32KNM, Pu136. 8BKON a- 82.79mm, Mu- 356.17KN m, Pu153 7KN a- 165.58mm, Mu - 295 32KN-m, Pu =78 0SKN a 110.81mm, Mu 316 33KNM, Pu 150.89KN
5. The beam-column has a height of 7.5m and is a member of a braced frame. It is subjected to an axial load of DL-65KN and LL= 1OOKN. It is pinned at both ends. A W12X35 section was used and was made up of A-36 steel with Fy-250MPA. Compute the interaction value for beam- column based on NSCP 2015 code provisions. Ngelect the weight of the section. A = 6645 mm2 Zx- 839x10^3 mm3 d- 317.50mm Sx- 747x10^3 mm3 tw= 7.62 Rx= 133.35 bf= 166.62 ly= 10x10^6 mm4 tf- 13.21 Sy= 122x10^3 mm3 Ix= 119x10^6 mm4 Ry3 39.12mm 3.5 Note: Use C=D1.00%--0.2
Q4. Considering BOTH strength and deflection criteria in approximate truss design, what would be the maximum distributed load, w, that the below truss can carry? d is the distance between the top and bottom boom. Given: alloeable - 200 MPa - Span 350 W 20kN 15m Sallowable E = 200 GPa d= 1.5m Cross-section area of tensile or compressive boom (not together) A= 2500mm
Where is/are the location(s) of the maximum compressive flexural stress? A simple I-beam is loaded as shown. 20 mm P KN PKN P KN B 20 mm- B с D L/4 m L/4 m L/4 m Pin support at the NA Midspan at point B Mid span at point D Midspan at the top fiber Roller support at top fiber Section D at the top fiber Section C at +170 mm from the NA L/4 m 20 mm C 250 mm 150 mm 150 mm D A
PROBLEM 2: The steel beam loaded below has the built-up cross section as shown. Determine the maximum permissible value of the load w so as not to exceed allowable bending stresses of 110 MPa. -125 mm- w (including beam weight) 20 mm 20 mm 100 mm .-- NA A B - 2 m - 6 m 20 mm FINAL ANSWER: Max. allowable w kN/m
4-1 Figure P4.1 shows a simply supported beam and the cross section at midspan. The beam supports a uniform service (unfactored) dead load consisting of its own weight plus 1.4 kips/ft and a uniform ser- vice (unfactored) live load of 1.5 kips/ft. The con- crete strength is 3500 psi, and the yicld strength of the reinforcement is 60,000 psi. The concrete is normal-weight concrete. Use load and strength- reduction factors from ACI Code Sections 9.2 and 9.3. For the midspan section shown in Fig. P4-1b, compute M, and show that it exceeds Mu- Wo = 14 kips/it plus weight of beam WL - 1.5 kipa/it (a) 20 ft 21.5 in. 24 in. (b) 3 No. 9 bars 12 in. Fig. P4-1
A reinforced concrete simply supported beam has a span of 20 ft and supports service dead load of 2.5 kip/ft and a uniform service live load of 2.5 kip/ft in addition to its self-weight. Design a beam section as per ACI 318-14 to resist the factored external bending moment. The concrete compressive strength at 28 days is(4 + 15)ksi and yielding strength of steel is (60+ 15)ksi.
University of Al-Qadisiyah- Civil Eng. Dept. Lecture 11; Shear design.mp4 Example 1 GIF the rectangular beam given in figure below has been designed for flexure; design the necessary shear reinforcement given that that beam is loaded by a uniformly distributed live load of 25 kN/m and a dead load (including self-weight) of 40 kN/m, take f. = 28 MPа, fyt 3 420 MPа, о 542 mm 600 mm 5020- +300 mm Face of Support 300 mm 7.0 m 44:רן •..