A gas mixture containing 30 mol% C3H8 and 70% n-C4H10 at 0 ° C temperature and 1.1 atm pressure is mixed at a flow rate of 300 L / h. Another gas mixture containing 45 mol% C3H8 and 55% n-C4H10 at 25 ° C temperature and 1.1 atm pressure is mixed at a constant pressure of 227 ° C with a flow rate of 132 L / h. Calculate the amount of heat required in kJ / h. C3H8 and n-C4H10 enthalpies are given below. Make an ideal gas acceptance.

Q: Course dasnboara Calculate the height of a column of liquid glycerol (d= 1.26 g/cm3), in meters, req...

A: density of liquid glycerol(d1)= 1.26gm/cm3=1260kg/m3density of water(d2)=1000kg/m3=1g/cm3heigh of wa...

Q: A gas mixture containing 7% CO2, 0.5% O2, 38% CO and 50.5% H2 (the remainder is N2) is incinerated w...

A: BASIS: 100mole of feed given: CO2=7% O2=0.5% CO=38% H2=50.5% N2=4% Excess air=20% humidity=0.02kg/kg...

Q: a) Write down the required appurtenances, structures, and facilities for the control of leachateorig...

A: Hello Subscriber ! You have, in effect,  posted two separate questions. We have answered the first o...

Q: A gas mixture containing 7% CO2, 0.5% O2, 38% CO and 50.5% H2 (the remainder is N2) is incinerated w...

A: Assumption: 100 mols of feed gas. Then we have, CO2= 7mol, O2=0.5mol, CO= 38mol, H2=50.5mol And N2=1...

Q: 3.) A steel bar 100 mm long and having a square cross section 20 mm on an edge is pulled in tension ...

A: Given: Length of steel bar=100 mm=100×10-3mCross section of the steel bar=20 mm=20×10-3mForce=89000 ...

Q: Consider that the complete combustion of 15 moles of methane, CH4 a. What is the mass in kilograms o...

A: Methane is present in natural gas, it is used to generate energy after combustion of methane. The co...

Q: Can i get step by step help with this problem step by step please

A: We are asked to find the compound which has M+ and M+2 peaks of equal density.  

Q: Show complete solution and box all final answers. Observe and show all proper units.

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question s...

Q: How many micrometers are there in a nanometer? 10 100 1000 1,000,000 Which of these is the correct s...

A: The conversion of a unit requires the multiplication or division of the number by a specific numeric...

Q: The vapor pressures of solid and liquid chlorine in the vicinity of the triple point are given by 37...

A: Vapor pressure of the solid chlorine in the vicinity of the triple point is given as: lnPSolidPa=26....

Q: 5. (x) Saturated Vapor H2O at 2.00 kPa, determine the Quality as a decimal (not a percentage).

A: Given, Pressure of the saturated vapor is 2.00 kPa.   Quality is defined as the fraction of vapor pr...

Q: 3) Vapor-Liquid Equilibrium: Flash Separations (CHEN 3110 Thermodynamics) For each of the following ...

A: The following problem demonstrates the flash separations. The boiling point is defined as the temper...

Q: At least half of Malaysia’s demand for electricity is met by natural gas. In a natural gas-fired pow...

A: Diagram based on the process description with the streams and known information and unknown variable...

Q: Show complete solution. Box all final answers.  See attached photos for possible answers. Make sure ...

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you. ...

Q: When a flammable material is burned, there will be an increase in either the volume of the gas produ...

A: Given: Moles of propane=200kmol Pressure in container=1 atm Temperature n container=25°C Air used=20...

Q: Consider the autocatalytic reaction A→  R, with-rA 0.001 CACR mol liter s. We wish to process 1.5 li...

A:  Given: The autocatalytic reaction given is as follows: A → R Volumetric flow-rate vo = 1.5 L/sec In...

Q: Show complete solution and box all final answers. Show all computations with proper units.

A: Given data: Enthalpy of steam at the inlet of pipe = 2870.7 kJ/kg Specific volume of steam at the in...

Q: Air is flowing through a pipe. A manometer is attached to the pipe to measure the pressure in the pi...

A: It is to be explained why height of the air in a manometer is neglected.

Q: 17

A: Diffusion is a mass transfer phenomena of transferring of mass or moles of a substance from one loca...

Q: The feed water of an industrial reactor has a total hardness of 250 mg L-1 of CaCO3. To reduce this ...

A: The hardness of water is the amount of dissolved calcium and magnesium in the water. Hard water is h...

Q: Given the reactions (1) and (2) below, determine (i) ΔrH and ΔrUfor reaction (3),(ii) ΔfH for bot...

A: Write the reactions as follows: H2(g) + Cl2(g) → 2HCl(g); ΔrH = −184.62 kJ/mol Multiply with 2 on bo...

Q: Need help figuring out these equations and problems, I need a guide to solve one so I can figure out...

A: The ratio of concentrations of a compound in a mixture of two immiscible solvents at equilibrium is ...

Q: A ==> 2R.  A reactor is to be designed for 80 % conversion of A with a feed concentration of 10 m...

A: A→2RXA=0.8CA0=10mol/Lv0=10L/sto find: CAexit ε=2-11=1 design equation of MFR: Vv0.CA0=XA-rAexit let ...

Q: example give 3 reasons for the selection of glass as the ideal packaging material for a food product...

A: For a wide range of food products that are heat-treated or packed with pressure, glass packaging is ...

Q: Steam enters an adiabatic turbine at 2MPa, 400°C at a velocity of 50 m/s. It leaves at 15 kPa and 18...

A:                       

Q: Inner and outer diameters of 12 pipes used in a one shell one pass horizontal condenser are 2.2 cm a...

A: Given: Hot fluid: Th = 60 oC mh = 0.045 kg/s hf = 2366 kJ/kg Cold Fluid: Tc1 = 20 oC mc = 6 kg/s   R...

Q: A stoichiometry experiment was performed using an unknown sample of the KClO3 – KCl mixture and the ...

A: Given: Mass of tube and catalyst: 20.6200 g Mass of tube catalyst and unknown mixture: 22.6200 g Tub...

Q: The maximum allowable temperature for a reactor is 800 K. At present our operating set point is 790 ...

A:

Q: Please solve question 13

A:

Q: A. You were asked to design and manufacture a plate heat exchanger, as shown in the figure, to be us...

A: Since you have asked a question with multiple sub-parts, we will solve the 1st three sub-parts for y...

Q: Problem #1 The relationship between temperature in Fahrenheit and Celsius is linear. Water is defin...

A: Temperature of a system gives the idea whether it is hot or cold. It is a physical quantity. Tempera...

Q: a) Calculate the standard free energy of formation for ozone at 298oK from the values of ΔHof and So...

A:

Q: 1. Consider a solution that contains albumin at a concentration of 54 g/L. This solution is fed thro...

A: Evaporation is the process of turning from a liquid into vapor. It occurs at any temperature with va...

Q: An old process for the production of hydrochloric acid requires heating a mixture of NaHSO4 and NaCl...

A: Hydrochloric acid is an aqueous solution of hydrogen chloride. It is also known as muriatic acid. It...

Q: Draw or illustrate the difference between intensive and extensive property.

A: The difference between the intensive and extensive property is to be illustrated.

Q: 5. Given H2O at 210°C, 0.1 MPa (a) find the phase. (b) what is the quality (as a decimal)? (c) what ...

A: The temperature and pressure of water are given as:   T = 210°C P = 0.1 MPa

Q: Table 2.6 Triad distributions in two ethylene/1-hexene copolymers (21)   83/17 Copolymer 97/3 Cop...

A: The given table for the triad distribution of two ethylene/1-hexene copolymers is:   83/17 Cop...

Q: (ii). x=4 In a chemical industry, air of volume 0.03 m3 is cooled from a temperature of 32X. 15 K to...

A: Volume of air, V = 0.03 m3 Initial air temperature, T1 = 324.15 K Final air temperature, T2 = 294.15...

Q: Tooth enamel is composed of hydroxyapatite, whose simplestformula is Ca5(PO4)3OH, and whose correspo...

A: (a) Write the reaction for the dissolution of hydroxyapatite as follows: Ca5PO43OHs  ↔ 5Ca2+aq +3PO4...

Q: Given Fet + 2e Fe, E° = -0.440 V, and Fe+ + e - Fet, Eo= 0.771 V, calculate E° for Fe* + 3e - Fe.

A:

Q: The speed of the response of a first- order system is determined by the time constant for the system...

A:

Q: An equilibrium reaction of the type :   is carried out in a 120 L continuous stirred tank reactor. T...

A:

Q: Show complete solution. Round everything to 4 decimal places. Show all units and box all final answe...

A: Heat flows into the system from state a to state b along the path acb, Qacb = 100 J Work done by the...

Q: Show complete solution.Round everything to four decimal places and box all final answers. No units, ...

A: Given data: Number of moles of gas = 1 mol A gas undergoes four step thermodynamic cycle.  Thermodyn...

Q: Cleanup of a mercury spill in an unventilated stockroom fails to remove the mercury trapped in small...

A: Given: Temperature = 23 oC = 296 k The permissible limit for mercury in air = 0.1 mg/m3 The properti...

Q: Explain in detail on the E unsteady state material balance for a suitable system with example.

A:

Q: Calculate the fraction of atom sites that are vacant for copper at its melting temperature of 1084°C...

A: The atomic vacancies is depends on the energy required for vacancy creation, it is also dependents o...

Q: Making differential momentum balance for laminar flow through a narrow slit

A:

Q: B) Paper mills ships to a distributor 12.2kg of paper. A sample carefully taken at the mill is found...

A:

Q: In two different container at 20,48°C contain 1.241M and 250ml HCl .There are 0,451M and 300ml Ba(OH...

A: For the reaction we have 2HCl + Ba(OH)2 ----------> BaCl2 + 2H2O moles of HCl = .25*1.24= .310mol...

Reactive Processes

Reactive processes are the processes in which any reaction occurs. The reactions can be any combination reaction, decomposition reaction, combustion reaction, oxidation reaction, reduction reaction, neutralization reaction, displacement reaction, or double displacement reaction.