A gear reduction system consists of three gears A. B, and C. Knowing that gear A rotates clockwise with a constant angular velocity a- 600 rpm, determine (a) the angular velocities of gears B and c, (b) the accelerations of the points on gears B and C which are in contact.

A gear reduction system consists of three gears A. B, and C. Knowing that gear A rotates clockwise with a constant angular velocity a- 600 rpm, determine (a) the angular velocities of gears B and c, (b) the accelerations of the points on gears B and C which are in contact.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In the planetary gear system shown, the radius of gears A, B, C, and D is 30 mm and the radius of the outer gear E is 90 mm. Knowing that gear E has an angular velocity of 180 rpm clockwise and that the central gear A has an angular velocity of 240 rpm clockwise, determine (a) the angular velocity of each planetary gear, (b) the angular velocity of the spider connecting the planetary gears.
) An overhead door is guided by wheelsn at A and B that roll in horizontal and vertical tracks. Knowing that when θ= 40° the velocity of wheel B is 0.5 m/s upward, determine (a) the angular velocity of the door, (b) the velocity of end D of the door.
A chain is looped around two gears of radius 40 mm that can rotate freely with respect to the 320-mm arm AB. The chain moves about arm AB in a clockwise direction at the constant rate of 80 mm/s relative to the arm. Knowing that in the position shown arm AB rotates clockwise about A at the constant rate ω = 0.75 rad/s, determine the acceleration of each of the chain links indicated Links 1 and 2.
In a four bar mechanism, the dimensions of the links are as given below:AB = 50 mm, BC = 66 mmCD = 56 mm and AD = 100 mmAt a given instant when | DAB=60°the angular velocity of link AB is 10.5rad/sec in CCW direction.Determine,i) Velocity of point Cii) Velocity of point E on link BC when BE = 40 mmiii) The angular velocity of link BC and CDiv) The velocity of an offset point F on link BC, if BF = 45 mm,CF = 30 mm and BCF is read clockwise.v) The velocity of an offset point G on link CD, if CG = 24mm, DG = 44 mm and DCG is read clockwise.vi) The velocity of rubbing of pins A, B, C and D. The ratios ofthe pins are 30 mm, 40 mm, 25 mm and 35 mmrespectively.
Cylinder A is moving downward with a velocity of 3 m/s when the brake is suddenly applied to the drum. Knowing that the cylinder moves 6 m downward before coming to rest and assuming uniformly accelerated motion, determine (a) the angular acceleration of the drum, (b) the time required for the cylinder to come to rest.
A juggling club is thrown vertically into the air. The center of gravity G of the 20-in. club is located 12 in. from the knob. Knowing that at the instant shown, G has a velocity of 4 ft/s upward and the club has an angular velocity of 30 rad/s counterclockwise, determine (a) the speeds of points A and B, (b) the location of the instantaneous center of rotation.
In a four-link mechanism, the dimensions of the links are given as AB=50mm, BC=66mm, CD=56mm, and AD=100mm. At the instant when <DAB = 60° , the link AB has an angular velocity of 10.5 rad/sec in the counterclockwise direction. Both A and D lies in the horizontal plane.For the given configuration of the mechanism, determine the following: angular velocity of the link CD, angular velocity of the link BC, velocity of an offset point G on the link CD if CG=24mm,DG=44mm Instructions: configuration diagram Scale: 1:1 velocity diagram. Scale: 1m/s : 95mm
Knowing that at the instant shown the angular velocity of bar AB is 15 rad/s clockwise and the angular velocity of bar EF is 10 rad/s clockwise, determine (a) the angular velocity of rod DE, (b) the relative velocity of collar B with respect to rod DE.
A painter is half way up a 10-m ladder when the bottom starts sliding out from under him. Knowing that point A has a velocity vA = 2 m/s directed to the left when 0= 60°, determine (a) the angular velocity of the ladder, (b) the velocity of the painter.
A circular plate of 120-mm radius is supported by two bearings A and B as shown. The plate rotates about the rod joining A and B with a constant angular velocity of 26 rad/s. Knowing that, at the instant considered, the velocity of point C is directed to the right, determine the velocity and acceleration of point E.
Ring C has an inside radius of 55 mm and an outside radius of 60 mm and is positioned between two wheels A and B, each of 24-mm outside radius. Knowing that wheel A rotates with a constant angular velocity of 300 rpm and that no slipping occurs, determine (a) the angular velocity of ring C and of wheel B, (b) the acceleration of the points on A and B that are in contact with C.
In a four bar mechanism, the dimensions of the links are given as AB = 50 mm, BC = 66 mm, CD = 56 mm and AD = 100 mm. At a given instant when <DAB=600 . The angular velocity of link AB is 10.5r/s in CCW direction. Determine, (i) velocity of point C, (ii) velocity of point E on link BC when BE = 40 mm, (iii) the angular velocity of link BC and CD; (iv) the velocity of an offset point F on link BC, if BF = 45 mm, CF = 30 mm and BCF is read clockwise. (v) the velocity of an offset point G on link CD, if CG = 24 mm, DG = 44 mm and DCG is read clockwise (