A generating station distributes the following loads. 3000 kW ,8000 kW,14000 KW and 4000 kW. The maximum demand of the station is 30 MW. The annual load factor is 60%. So – find (1) diversity factor (2) demand factor and (3) number of units supplied.

A generating station distributes the following loads. 3000 kW ,8000 kW,14000 KW and 4000 kW. The maximum demand of the station is 30 MW. The annual load factor is 60%. So – find (1) diversity factor (2) demand factor and (3) number of units supplied.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.26P: A small manufacturing plant is located 2 km down a transmission line, which has a series reactance...

See similar textbooks

Related questions

Q: The output modules cannot handle as much current per output The input modules cannot handle as much…

Q: 5. Find Vo. 34 Μ 16Ω ΤΩ ΤΩ ΑΜΕ ΤΩ 12V 109

Q: + JO loudspeaker is an electromechanical system that can be modeled by the electric circuit and the…

A: An electromechanical energy conversion device is one that transforms mechanical energy into…

Q: A series R-L-C circuit having resistance 50 2, inductive reactance 0.2 H and capacitance 10uF is…

Q: ль 2 3 .yu - 2k 1K 3k sk. 1. L प्रह Vout

Q: tan2t8 (t - 7/3 8

Q: 18-14 Given that the Fourier transform of f(t) is F(Ⓡ) = 50,000 (jo +100) (jo +500) Use the…

Q: Given a system with input x(t) = u(t) and impulse response h(t) shown below. Determine: a) The…

Q: A certain counting type 12 bit ADC operates with FSR = 0 to 10 V and clock Frequency folk 1 MHz.…

A: Given- 12 bit ADC, FSR=0 to 10 V, clock frequency fclk=1 MHz, To Find- (1) Dynamic range of…

Q: 1. Given the following resistors, determine the total resistance if a. all are connected in series.…

Q: 1- For a system with the transfer function Y(s) 2s³ - 12 U(s) 4s5 S3 + 4s 10 The state matix is…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Problem 2.4b: Sketch double sided and single sided amplitude and phase spectra of the following.…

Q: Example 5.16. A square ABCD has each side of 1 m. Four point charges of +0.01 µC, -0.02 μC, +0-03 μC…

A: We have been asked to find the potential at point P which is center point of square which is being…

Q: A resistance strain gauge with gauge factor of 2 is bonded to a steel member, which is subjected to…

A: Given, Gauge factor, GF=2. Strain, ∆LL=1×10-6. Original resistance value, R=120 Ω. Change in…

Q: 6. Please prove the following: X 8(kx) * () = S(x) k where is convolution operation, and k is a…

Q: Refer to the circuit shown in Fig. 11.88. (a) What is the power factor? (b) What is the average…

Q: 3.4 Determine U, in the circuit of Fig. 3.11. 2 Α 30 V ww 8 Ω – FIGURE 3.11 Μ 2 Ω 10 Ω ΣΩ 2 Ω + υχ…

Q: T lines are designed for Digital data how they can be used for Analog Transmission?

A: Digital Transmission of analog information is possible if a minimum level of signal to noise is…

Q: Determine whether the following signals are energy, power, or neither energy nor power.

Q: Discuss some problems that might result from developing facilities for conversion of wave energy to…

A: Wave Energy:- The constant movement of the waves as they roll against the coast and then out again…

Q: Question A sinusoidal signal with a peak voltage of 10V is input into a frequency dependent circuit.…

A: Given data, Peak value of input voltage Vp=10 V

Q: choose the correct expression for (A + B C D O A+B+CD B + C + D B + C + D A B + C + D A OA ||

A: Given a Boolean expression, F=A+B¯.C.D¯

Q: Linear variable differential transformers (LVDTs) are used in some laboratoryexperiments. What is…

A: LVDT: LVDT stands for linear variable differential transformer. This is used to measure the linear…

Q: 18–12 Use the duality property to find the inverse transforms of the following functions: a. F₁(0)…

A: Since you have posted the all different questions so we are supposed to answer the 1st one.

Q: What are Hall probes and how they work?

A: A Hall probe is a tool that uses a calibrated Hall effect sensor to measure a magnetic field's…

Q: The potential difference across the terminals of a cell is 1.5 volts. It is connected (1) with a…

A: It is given that: V=1.5 voltsR=30 Ω

Q: A coil has resistance 10 Ω , inductive reactance 20 Ω . A capacitance of 50 uF is connected in…

Q: A discrete-time system has the following unit-pulse response, Find the response of this system y[n]…

Q: A direct current shunt motor develops 10 HP at 8000 RPM when drawing a line current of 40 A at 220…

Q: 2. x[n] = cos ¹n 4

Q: Find the Req

A: The equivalent resistance of the given network can be obtained by reducing the parallel and series…

Q: A unity feedback system with G(S) = K S(S+20)(S+40) is operating at 20% overshoot. Design a…

A: Here, given system is standard third order system as it contains three poles and no any zero. With…

Q: A 33 kV single core cable has a conductor diameter of 1 cm and a sheath of inside diameter 4 cm.…

A: We have an single core cable which has a, Diameter (d) = 1 cm Sheath diameter (d) = 4 cm Voltage (V)…

Q: Using the voltage divider rule, find the indicated voltages V₁ and V₂ in the circuit shown below. Μ…

A: The given circuit is,

Q: What is the impedance of an inductor of 5mH at a radian frequency of 2x10^3 rad/s? Z= ohms

A: Given: An inductor has the specifications, Inductance, L=5 mH. Frequency, ω=2×103 rad/s.

Q: With reference to the I/O image tables: What is the input status of a closed switch stored as? What…

A: Warm systems with PLC redundancy typically function in shadow mode, sharing a heartbeat signal from…

Q: 18-18 The input in Figure P18-18 is v₁(t) = 10 sgn(t) V. Use Fourier transforms to find Ug(t). V (1)…

Q: A 10 KVA, 2000/400 V single phase transformer has R1=50, X₁ = 120, R₂ = 0.20 and X₂ = 0.48 2.…

A: We have an single phase transformer having, Primary voltage = 2000 V Secondary voltage = 400 V R1 =…

Q: The wave Fom X(t) = 20 +20 sin (500t +30°) is to be Sampled periodically and later to be reproduced…

A: Please comment if you need any clarification. If you find my answer useful please put thumbs up.…

Q: Find the main dimensions of a 2000 kVA, 187.5 rpm, 50 Hz, 3 phase salient pole synchronous…

Q: Two resistances of 4 ohms and 6 ohms in parallel are in series with another resistor of 12 ohms. If…

Q: 10. The following is part of a larger circuit. The 4 branches extending outward are not open…

A: Given circuit:

Q: Given the AM voltage equation. Determine the carrier voltage and frequency, the modulating voltage…

A: Given: VAM=310 cos (6,540,000 t)+650 sin (6,600,000 t) - 310 cos (6,660,000 t) Volts To do:…

Q: 2- Find fourier Coefficients CK for x(n). Axen) III. 111.

Q: Three resistance of 6 , 12 and 16 are connected in star connection. Find its equivalent delta…

A: We have been given three resistance with, R1 = 6 Ω R2 = 12 Ω R3 = 16 Ω This three resistance are…

Q: peak current through the resistor is A. 15 MA B. 1.5 mA 10 mA

A: Given data:- Vrms = 16 V R = 15 kohmIPeak =?

Q: A balanced load of phase resistance 36 and capacitive reactance of 40 is connected in star…

A: Given data: Phase voltage at load: Vphase=255 VZphase=36-40j

Q: What is the maximum number of simultaneous calls in each cell in an IS-136 (D-AMPS) system, assuming…

A: IS-136 is a mobile communication standard, They are the second generation (2G) technology cellular…

Q: [11] 5- A system with input matrix B= 0 1 has Lo 1 c- four inputs a- one input b- two inputs d-six…

A: As per the guidelines, we are supposed to answer only first question for multiple type questions.…

Q: Find up and U2 32 V + 4Ω +91- + 2 Ω −8 V

A: The given circuit is,

Concept explainers

Maximum power transfer theorem

A resistive load will consume maximum power from a network when the load resistance is equal to the resistance of the network as viewed from the open-circuit terminals, with all energy sources removed leaving only the internal resistances. Physicist Moritz von Jacobi introduced the maximum power transfer theorem in 1940. Therefore, this theorem is also known as Jacobi's law.

Question

100%

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Under balanced operating conditions, consider the three-phase complex power delivered by the three-phase source to the three-phase load. Match the following expressions, those on the left to those on the right. (i) Realpower, P3 (a) (3VLLIL)VA (ii) Reactive power, Q3 (b) (3VLLILsin)var (iii) Total apparent power, S3 (c) (3VLLILcos)W (iv) Complex power, S3 (d) P3+jQ3 Note that VLL is the rms line-to-line voltage, IL is the rms line current, and is the power-factor angle.
A small manufacturing plant is located 2 km down a transmission line, which has a series reactance of 0.5/km. The line resistance is negligible. The line voltage at the plant is 4800V(rms). and the plant consumes 120kW at 0.85 power factor lagging. Determine the voltage and power factor at the sending end of the transmission line by using (a) a complex power approach and (b) a circuit analysis approach.
For the maximum average power transfer in the circuit shown in Figure 2, use the impedance ??.and ??Find the value of the maximum average power transferred to ? (Can you write the steps in detail in sentences?)
Explain about the power production scenario and write down about the growth.
How does power factor correction impact the efficiency and reliability of power systems?
What are the elements which contribute to the cost of the electricity? And discuss how the “load curves’ and ‘load duration curves’ can helpful in the economics of generation.
Pls. Answer thank you! A generating station has a maximum demand of 25MW, a load factor of 60%, a plant capacity factor of 50% and a plant use factor of 72%. Find the reserve capacity of the plant in MW.
An area of an interconnected power system has two fossil-fuel operating on economic dispatch. The variable operating costs of these units are given by in image Determine the power output of each units, the incremental operating cost, and the total operating cost that minimizes when total load demand is 250, 500, 750, 1000 and 1250 MW, transmission losses is neglecting?
An a electric power system A 200 MW unit with 0.05 pu turbine operates in parallel with a 400 MW unit of identical turbine regulation. For a specified amount of power demand in crease, find the ratio of sharing of the Load by the units, system frequency is 50Hz .
Discuss the significance of power generation, transmission, and distribution in the context of a reliable and efficient power supply. What are the challenges associated with each of these phases?
The yearly duration curve of a certain plant can be considered as a straight line from 300 MW to 80 MW. Power is supplied with one generating unit of 200 MW capacity and two units of 100 MW capacities each. Determine: Installed Capacity, Load Factor, Plant Factor, Maximum Demand and Utilization Factor.
a question by considering the annual load time curve for an electric station as a straight line from 20mw to 3mw, and to cover these loads, then operate three generating units, the first and second, each with a capacity of 10mw, while the third has a capacity of 5mw, and illustrate the load time curve by drawing, then find: 1- the total capacity of the station 2- the maximum demand 3- capacitance coefficient 4- pregnancy coefficient 5 utilizatio