Answered: A 33 kV single core cable has a…

A 33 kV single core cable has a conductor diameter of 1 cm and a sheath of inside diameter 4 cm. Find the maximum and minimum stress in the insulation.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter4: Transmission Line Parameters

Section: Chapter Questions

Problem 4.3P: A transmission-line cable with a length of 2 km consists of 19 strands of identical copper...

See similar textbooks

Related questions

Q: a. Find the voltage and current across resistor R2. Also indicate the value of the current through…

Q: An unbalanced 2-0, 1000 V, 50 Hz induction motor has unequal winding impedances, Z₂=3+j2.7 and Z=…

A: Given- 2-ϕ, 1000 V, 50 Hz, Induction motor. Impedance- Za=3+j2.7,Zb=7+j3 Ω, To Find- Phase currents…

Q: B- A Blood warming device contains a 20 mm diameter copper pipe is used to carry warm water, the…

A: SOLUTION GIVEN---> Blood Warming device diameter= 20mm ==>…

Q: An ebony circular disk has a uniformly charge density of 2 C per square meter. The radius of the…

A: Given, A uniform circular disk has a uniform charge density ρ=2 C/m2. Radius of the disk r=1 cm.

Q: What is the name of the wires that connect the memory?

A: Memory: Memory serves as the computer's electrical storage facility for the instructions and data…

Q: For the system shown in Fig. 1, the system has a transmission line of unknown length and unknown…

A: The output impedance, or opposition to current flow, refers to the impedance of the component that…

Q: The reverse recovery time of a diode is t,,= 6 us, and the rate of fall of the diode current di/dt =…

Q: choose the correct expression for A + A B C : °A + Вс ОB+A C O B + AC C+ AB

A: Given logic expression, F=A+A.B.C

Q: 93- Find fourier Coefficient C for xen) x(n) = { 0.-2, 2, 1, 0, -2, 2,1-] x(n) =…

Q: 10. When there is 12 mA of current through a 1.2 kn resistor, the voltage across the resistor is

Q: Find the node voltage at node 1 in the following circuit. 192 352 www 10A 1092 :502 €10V

A: Given circuit,

Q: 3 phase, 220 k 50Hz transmission line consists of 1.5 cm radius conductor spaced 2 metres apart in…

Q: x(t) = e/[(x/2)t-1]

A: Given: x(t)=e j[(π2)t-1] To do: Determine whether x(t) is periodic or not. If the signal is…

Q: A straight thin glass rod holds a charge Q= 2C over a length of 1m. Determine the charge density in…

A: Given: A straight thin glass rod has, Charge Q=2C. Length L=1 m.

Q: What is settle time?

A: Settle time: The time that has passed between the application of an ideal instantaneous step input…

Q: 1. The transfer function of the control system is given by C(S) 32 R(S) (4s² + 12s + 256) a. Find…

A: Note: Since we only answer up to 3 sub-parts, we’ll answer the first three. Please resubmit the…

Q: A 100 kVA, 220/440 V, 50 Hz power transformer is tested at 75 Hz to evaluate the core los while its…

A: Given, A 100 kVA, 220/440 V, 50 Hz power transformer is tested at 75 Hz to evaluate the core loss,.…

Q: 12 v 100 Ω B 200 Ω · A C E 300 < What is the Equivalent Resistance through A to E?

A: Given circuit:

Q: Find the inverse transforms 100 F₁(0) = jo 100 F₂(0) = F3(0) = 500 (jo+100) (jo+500) 500 jo…

Q: 9.0 V I 40 Ω ww 50 Ω

Q: 5.18 Consider the two-port network as shown. The hybrid parameter his (a) (c) 04 V₁ ww R₁ (aR3 + R₂)…

A: Given two port network,

Q: An unbalanced 2-0, 1000 V, 50 Hz induction motor has unequal winding impedances, Z₂=3+j2.7 and Z=…

A: It is given that: Za=3+j2.7 ΩZb=7+j3 Ω2-ϕ,1000V,50 Hz IM3-ϕ,11kV system

Q: 13. If the percentage reactance of the system upto the fault point is 20% and base kVA is 10,000,…

A: Given, Percentage reactance of the system up to fault point, % X=20 % Base kVA rating is 10,000 kVA.

Q: 16V +1 www 4Ω 8H ₁₁ The circuit above is in DC steady state. What is the value of it in amps? www…

Q: The span of the same level transmission line is 300 meters. The diameter of the conductor is 15 mm.…

Q: 12 v 100 Ω B 200 Ω A E 300 Ω How much power is the battery supplying?

A: Given circuit:

Q: Q1) Determine the corona characteristics of a 3-phase line 160 km long, conductor diameter 1.036 cm,…

Q: Consider the following section of a multiloop circuit, with current directions as indicated: zero B…

A: Given circuit,

Q: F(A,B,C,D)=Σm(0,1,2,6,7,8,11,13,14,15) a. Derive the Karnaugh map from Truth Table b. Simplify the…

A: Given minterm Boolean function, FA,B,C,D=∑m0,1,2,6,7,8,11,13,14,15.

Q: A d.c. A shunt generator delivers a load current of 80 A at 400 V. Its armature and field…

A: Solution: Given data: shunt generator: V=400 V, load current IL=80 A, armature resistance Ra=0.2Ω,…

Q: Determine the product of (1 + i) and (1-3i) (A) 4-2i B) 2-2i C) 2-4i (D) 2+4i

A: Given: To determine the product of 1+i and 1-3i.

Q: a) Based on Figure Q1(a), prove that the voltage across resistor R3 is; R3 R₁ + R₂ + R3 VR3 = V₁ VRI…

A: Given circuit: To prove: Voltage across resistor R3 is VR3=R3R1+R2+R3VT.

Q: In the centre-tap circuit shown in Fig. 6.31, the diodes are assumed to be ideal i.e. having zero…

A: WE have an center-tap circuit as shown in figure, We need to determine, DC output voltage Peak…

Q: 16 A 5 x 4.0 cm² laminated magnetic core has a flux of 5 mWb. Assuming a fringing factor of 1.125,…

Q: A strain gauge having a resistance of 500 ohm and a gauge factor 3.0 is bonded on a member of…

A: Given a strain gauge having, Resistance, R=500 Ω. Gauge factor, GF=3. Change in resistance, ∆R=1.5…

Q: E) What is the purpose of the resistor Rv ?....... F) True or false: 1-the BJT transistor is a…

A: A three-terminal semiconductor device called a bipolar junction transistor may amplify or magnify a…

Q: P4) Find the unknown current 12 Ω Μ 3 Ω ww 24 V + 6Ω 1 + 15 V

A: Given, The circuit is,

Q: 1. x(t) = elalu(t) a > 0

Q: What is the reserve capacity, if the maximum demand of generation of power is 50 MW, the load factor…

A: Given, Maximum demand MD=50 MW. Load factor LF=60%=0.6. Plant capacity factor PCF=50%=0.5.

Q: 12 A discrete relay type output module can be used to switch either AC or DC load devices. Why? OIt…

A: Relay:- An electrically controlled switch is a relay. It is made up of a set of working contact…

Q: 4 Find the F.T. of the following Signals using <-2 d 2 +t Ans differentiation prop. 2 F(w) = 4 (sin…

A: Writing the mathematical expression. ft=2ut+2-rt+2+2rt-2ut-2-rt-2Taking differentiation w.r.t.…

Q: The RMS value of the signal shown in the figure is: f(t) 10 -10 0 1 23 4 5 6 t(sec)

A: Given waveform,

Q: Consider the unity negative feedback discrete system with digital PID controller. If the transfer…

Q: IL TL 3. x[n] = cos n + sin n 3 4

Q: Determine whether or not each of the following signals is periodic. If a signal is periodic,…

A: A periodic signal has a fixed pattern and it repeats again and again for a certain period of time.…

Q: Two reactors are connected in series across a 10 V, 10 kHz source. They are spaced so that there is…

Q: Design a binary counter that counts from 0 to 5. At each clock pulse, 3 lights will be ON and 3…

A: According to the question, the given binary counter counts digits from 0 to 5. Also by using JK…

Q: In the following circuit, find the current Ix, and the voltage V1, For IL 4.2 mA. R 2k 6 mA 놀 Select…

A: Given data, iL=4.2 mA Circuit diagram is given as,

Q: choose the correct expression for B + A B C = °C+ A B B + AC о © 4 A + B с B+ A + A C

A: Given a Boolean expression, F=B+A.B.C

Q: Write an 8085 microprocessor Assembly Language Program to add two 16 bits numbers? If the frequency…

Question

A 33 kV single core cable has a conductor diameter of 1 cm and a sheath of inside diameter 4 cm. Find the maximum and minimum stress in the insulation.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

MAXIMUM STRESS

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The Aluminum Electrical Conductor Handbook lists a dc resistance of 0.01558 ohm per 1000 ft at 20C and a 60-Hz resistance of 0.0956 ohm per mile at 50C for the all-aluminum Marigold conductor, which has 61 strands and whose size is 1113 kcmil. Assuming an increase in resistance of 2 for spiraling, calculate and verify the dc resistance. Then calculate the dc resistance at 50C, and determine the percentage increase due to skin effect.
A transmission-line cable with a length of 2 km consists of 19 strands of identical copper conductors, each 1.5 mm in diameter. Because of the twist of the strands, the actual length of each conductor is increased by 5. Determine the resistance of the cable if the resistivity of copper is 1.72-cm at 20C.
The direct electrical connection of the windings allows transient over voltages to pass through the auto transfonner more easily, and that is an important disadvantage of the autotransformer. (a) True (b) False
Shield wires located above the phase conductors protect the phase conductors against lightning. True False
Alumoweld is an aluminum-clad steel conductor. True False
A 60-Hz, single-phase two-wire overhead line has solid cylindrical copper conductors with a 1.5 cm diameter. The conductors are arranged in a horizontal configuration with 0.5 m spacing. Calculate in mH/km (a) the inductance of each conductor due to internal flux linkages only, (b) the inductance of each conductor due to both internal and external flux linkages, and (c) the total inductance of the line.
Consider Figure 3.4. For an ideal phase-shifting transformer, the imda nce is unchanged when it is referred from one side to the other. (a) True (b) False
In developing per-unit circuits of systems such as the one shown in Figure 3.10. when moving across a transformer, the voltage base is changed in proportion to the transformer voltage ratings. (a) True (b) False
Consider the three single-phase two-winding transformers shown in Figure 3.37. The high-voltage windings are connected in Y. (a) For the low-voltage side, connect the windings in , place the polarity marks, and label the terminals a, b, and c in accordance with the American standard. (b) Relabel the terminals a, b, and c such that VAN is 90 out of phase with Va for positive sequence.
Rework Problem 3.14 if the transformer is delivering rated load at rated secondary voltage and at (a) unity power factor, (b) 0.8 power factor leading. Compare the results with those of Problem 3.14. -
Consider a single-phase electric system shown in Figure 3.33. Transformers are rated as follows: XY15MVA,13.8/138kV, leakage reactance 10 YZ15MVA,138/69kV, leakage reactance 8 With the base in circuit Y chosen as 15MVA,138kV determine the per-unit impedance of the 500 resistive load in circuit Z, referred to circuits Z, Y, and X. Neglecting magnetizing currents, transformer resistances, and line impedances, draw the impedance diagram in per unit.
How many transformers are needed to make an open-delta connection?