A generator feeds power to an infinite bus through a double circuit transmission line. A 3 phase fault occurs at the middle point of one of the lines. The infinite bus voltage is 1 pu, the transient internal voltage of the generator is 1.1 pu and the equivalent transfer admittance during fault is 0.8 p.u. The 100 MVA generator has an inertia constant of 5mJ/MVA and it was delivering 1.0 p.u. power prior of the fault with rotor power angle of 30°. The system frequency is 50 Hz. If the initial accelerating power is X pu, the initial acceleration in elect dag / sec, and the inertia constant in MJ – sec / elect deg respectively will be

A generator feeds power to an infinite bus through a double circuit transmission line. A 3 phase fault occurs at the middle point of one of the lines. The infinite bus voltage is 1 pu, the transient internal voltage of the generator is 1.1 pu and the equivalent transfer admittance during fault is 0.8 p.u. The 100 MVA generator has an inertia constant of 5mJ/MVA and it was delivering 1.0 p.u. power prior of the fault with rotor power angle of 30°. The system frequency is 50 Hz. If the initial accelerating power is X pu, the initial acceleration in elect dag / sec, and the inertia constant in MJ – sec / elect deg respectively will be

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter11: Transient Stability

Section: Chapter Questions

Problem 11.19P

See similar textbooks

Similar questions

The amplitude of the sinusoidal symmetrical ac component of the three-phase short-circuit current of an unloaded synchronous machine decreases from a high initial value to a lower steady-state value, going periods through the stages of __________ and ________ periods.
With the same transformer banks as in Problem 3.47, Figure 3.41 shows the oneline diagram of a generator, a step-up transformer bank, a transmission line, a stepown transformer bank, and an impedan load. The generator terminal voltage is 15 kV (line-to-line). (a) Draw the per-phase equivalent circuit, aounting for phase shifts for positive-sequence operation. (b) By choosing the line-to-neutral generator terminal voltage as the reference, determine the magnitudes of the generator current, transmiss ion-line current, load current, and line-to-line load voltage. Also, find the three-phase complex power delivered to the load.
PowerWorid Simulator case Problem 3_60 duplicates Example 3.13 except that a resistance term of 0.06 per unit has been added to the transformer and 0.05 per unit to the transmission line. Since the system is no longer lossless, a field showing the real power losses has also been added to the oneline. With the LTC tap fixed at 1.05, plot the real power losses as the phase shift angle is varied from 10 to +10 degrees. What value of phase shift minimizes the system losses?
A generator-transformer unit is connected to a line through a circuit breaker. The unit ratings are: Generator: 10 MVA, 6.6 kV; , and Transformer: 10MVA, 6.9133kV, reactance0.08pu The system is operating no load at a line voltage of 30 kV, when a three phase fault occurs on the line just beyond the circuit breaker' Find (a) the initial symmetrical rms current in the breaker’(b) The maximum possible DC off-set current in the breaker, (c) The momentary current rating of the breaker’ (d) The current to be interrupted by the breaker and the interrupting kVA and (e) The sustained short circuit current in the breaker
• Zh = 100 ohm • Draw the pu reactance diagram by taking Ut(base) = 132kV, St(base) = 100MVA. If the 33 kV busbar voltage is kept constant at 30 kV and 0.8 inductive 50 MVA power is drawn from this bus, what is the voltage at the synchronous machine ends?
Q5 (b) A synchronous generator and a motor are both rated at 30MVA, 2kV and both have transient reactance of 20%. The transmission line connecting them has a reactance of 10% on the base of the machine ratings. The motor is drawing 20MW at 0.8 power factor lagging and a terminal voltage of 12.8kV when a symmetrical three-phase fault occurs at the motor terminals. Using the internal voltage of the machines, carry out design calculations to determine: 1. The prefault generator terminal voltage. 2. The sub-transient current in the generator and the motor. 3. The total fault current 4. Comment on the relative sizes of the sub-transient currents in the generator and in the motor which were obtained in Q5 (b).
A generating plant containing three identical 40 MW generating units is connected to a constant 82 MW load. The unit failure and average repair times are 3 failures/year and 8 days respectively. Develop frequency, duration and probability risk indices for this system.
Three-phase, 60-Hz synchronous generator is connected through a transformer and paralleltransmission lines to an infinite bus. All reactances are given in per-unit on a common systembase. If the infinite bus receives 1.0 per unit real power at 0.95 p.f. lagging, determinea) the internal voltage of the generator andb) the equation for the electrical power delivered by the generator versus its power angle δ.
A three phase synchronous generator with negligible resistance and Xs=20 ohm has induced voltage as well as terminal voltage per phase equal to 230 V. for the load angle of 30o, power received by the bus is .........W.
a) The Newmont Mining Company at Ahafo in the Bono region of Ghana requested a dedicated power supply line from Kumasi in the Ashanti region of Ghana to feed its mining roller mills. The World Bank helped the Government of Ghana to fund the project. A company won the bid and came up with the design specifications as follows:The system would be a three-phase 138-KV transmission line and the total power to be connected to the line is 49-MV and would be operating at a 0.85 lagging power factor due to the large rotating motors in the roller mills. The line constants would have length of 120km long line with Z = 95∟78ºΩ and Y = 0.001∟90ºS.They are proposing to use nominal -T circuit representation in their analysis. If they are to provide:(i) The A, B, C and D constants of the line.(ii) The voltage from Kumasi to the NewmontWhat are the values you think the company that won the bid would provide?b) Using the information provided in a) above, Newmont Mining Company wants to know:(i) The…
a) The Newmont Mining Company at Ahafo in the Bono region of Ghana requested a dedicated power supply line from Kumasi in the Ashanti region of Ghana to feed its mining roller mills. The World Bank helped the Government of Ghana to fund the project. A company won the bid and came up with the design specifications as follows:The system would be a three-phase 138-KV transmission line and the total power to be connected to the line is 49-MV and would be operating at a 0.85 lagging power factordue to the large rotating motors in the roller mills. The line constants would have lengthof 120km long line with Z = 95∟78ºΩ and Y = 0.001∟90ºS. They are proposing to use nominal -T circuit representation in their analysis. If they are to provide:(i) The A, B, C and D constants of the line. (ii) The voltage from Kumasi to the NewmontWhat are the values you think the company that won the bid would provide? b) Using the information provided in a) above, Newmont Mining Company wants to know:(i) The…
At the end of the 8 km overhead line given in the figure below, there are two distribution transformers, one of which is 800kVA and the other is 1200kVA, operated with power coefficients of 0.6 and 0.8, respectively. The end-of-line voltage is 6kV. Find the required rated cross section and line head voltage so that the power loss on the line is less than %pk = 10.