A generator with constant 1.0 p.u. terminal voltage supplies power through a step-up transformer of 0.12 p.u. reactance and a double-circuit line to an infinite bus bas as shown in the following figure. The infinite bus voltage is maintained at 1.0 p.u.Neglecting the resistances and susceptances of the system, the steady statestability power limit of the system is 6.25 p.u. If one of the double-circuit istripped, the resulting steady state stability power limit in p.u. will be

A generator with constant 1.0 p.u. terminal voltage supplies power through a step-up transformer of 0.12 p.u. reactance and a double-circuit line to an infinite bus bas as shown in the following figure. The infinite bus voltage is maintained at 1.0 p.u.Neglecting the resistances and susceptances of the system, the steady statestability power limit of the system is 6.25 p.u. If one of the double-circuit istripped, the resulting steady state stability power limit in p.u. will be

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter11: Transient Stability

Section: Chapter Questions

Problem 11.19P

See similar textbooks

Similar questions

While the instantaneous electric power delivered by a single-phase generator under balanced steady-state conditions is a function of time havi ng two components of a constant and a double-frequency sinusoid, the total instantaneous electric power delivered by a three-phase generator under balanced steady-state conditions is a constant. (a) True (b) False
A single-phase, 120V(rms),60Hz source supplies power to a series R-L circuit consisting of R=10 and L=40mH. (a) Determine the power factor of the circuit and state whether it is lagging or leading. (b) Determine the real and reactive power absorbed by the load. (c) Calculate the peak magnetic energy Wint stored in the inductor by using the expression Wint=L(Irms)2 and check whether the reactive power Q=Wint is satisfied. (Note: The instantaneous magnetic energy storage fluctuates between zero and the peak energy. This energy must be sent twice each cycle to the load from the source by means of reactive power flows.)
An industrial plant consisting primarily of induction motor loads absorbs 500 kW at 0.6 power factor lagging. (a) Compute the required kVA rating of a shunt capacitor to improve the power factor to 0.9 lagging. (b) Calculate the resulting power factor if a synchronous motor rated at 500 hp with 90 efficiency operating at rated load and at unity power factor is added to the plant instead of the capacitor. Assume constant voltage (1hp=0.746kW).
Consider two interconnected voltage sources connected by a line of impedance Z=jX, as shown in Figure 2.27. (a) Obtain expressions for P12 and Q12. (b) Determine the maximum power transfer and the condition for it to
A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal step-up transformer (1:10), a transmission line (R=20 Ohm and X=60 Ohm), step down transformer (20:1) and a load with magnitude Z=10 Ohm and angle =30 degree the base values for this system are chosen to be 480 V and 10 kVA at the generator. Calculate the 1/per-unit impedance of the load 2/per-unit current in the line 3/ per-unit real power absorbed by the load
For the power system of Figure Q4.1, all per unit quantities have been calculated usinga common base. The generator delivers power p∞ = 1 p. u. at a lagging power factor ofcos= 0.93. i) Calculate the internal voltage of the generator, the maximum electrical powerthat the generator can deliver to the system during the steady state operationand the steady state rotor angle, σ0, of the generator.ii) A three-phase fault occurs at busbar 3 and it is cleared by simultaneouslydisconnecting lines 13 and 23. Following the fault clearing, the systemcontinues to operate with only line 12 in service. Determine the new steadystate rotor angle, σ1, of the generator and the maximum power the generatorcan deliver to the system post fault.iii) Assuming that the post fault condition is small disturbance stable and that thereis no negative interaction among system controllers, calculate the criticalclearing angle, σcr, at which the fault should be cleared to ensure the generatorreaches a new steady…
For the power system of Figure Q4.1, all per unit quantities have been calculated usinga common base. The generator delivers power p∞ = 1 p. u. at a lagging power factor ofcos= 0.93. i) Calculate the internal voltage of the generator, the maximum electrical powerthat the generator can deliver to the system during the steady state operationand the steady state rotor angle, σ0, of the generator.ii) A three-phase fault occurs at busbar 3 and it is cleared by simultaneouslydisconnecting lines 13 and 23. Following the fault clearing, the systemcontinues to operate with only line 12 in service. Determine the new steadystate rotor angle, σ1, of the generator and the maximum power the generatorcan deliver to the system post fault.
A simple power system is shown in this Fig. The generator (480 V, 10 kVA) is connected to an ideal step-up transformer (1:10), a transmission line (R=20 Ohm and X=60 Ohm), step down transformer (20:1) and a load with magnitude Z=10 Ohm and angle =30 degree the base values for this system are chosen to be 480 V and 10 kVA at the generator. Calculate the per-unit impedance of the load. Calculate the per- unit current in the line Select one: a. 1.43 A b. 0.569 A c. None of the above d. 2.01
Derive the full solution to the driven LRC circuit shown below using complex exponentials. Start withKirchhoff’s rule for the loop and assume a complex V (t) = V0eiωt (where by convention V0 is real) andassume that I(t) = I0eiωt where I0 is a general complex number (which can be written quite generallyas I0 = |I0|e−iδ), and where one gets physical answers at the end by taking the real part of thecomplex answers. Find an algebraic complex expression that expresses the sum of the voltages. Solve this expression directly using algebra, no pictures of “phasors” really required. Factor out the solution to obtain|I0|, δ, Z (the complex impedance), and the voltages across each element as a function of time.
The impedance ZL in the circuit shown in Figure is adjusted for maximumaverage power transfer to itself.(a) What should be the value of ZL?(b) What is the maximum average power delivered to ZL?(c) What percentage of the average power delivered to the linear transformer is delivered to ZL?
A Turgo type hydro-electric plant uses a 92% efficiency generator to produce its rated output of 32.5 MW. It was observed during its operation that the mechanical loss is 4.25 MW. Also, from the penstock down to the turbine, 14.3% hydraulic head loss and 8.9% leakage loss occurs which are equally distributed and based on the parameters at the dam. The average elevation from the headrace to the jet centerline is 40 m and from the tailrace to the jet centerline is 4.5 m. compute the following: a. Power by the turbine, kW b. Volume flow rate at the source, m3/s c. Power by the jet, kW d. Mechanical Efficiency, %
A power plant comprises three turbine-generators rated 1000 MW, 800 MW and 600 MW respectively. The regulation constant of each generator is 0.05 pu based on its own rating. Each unit is initially operating at one-half of its own rating, when the system load suddenly increases by 250 MW. Calculate the following:a) Per-unit area frequency response characteristic on a 1000 MW system base [CR9]b) Steady-state drop in area frequency [CR4]c) The share of the load increase on each generator [CR9]d) Total load on each generator after the increase in system load [CR3]Assume the reference power setting of each turbine is unchanged.