A getter screen consists of a cylinder of length l = 0.3m, diameter d=0.25m and its circular based plate. The getter screen is cooled with liquid nitrogen and coated completely with deposited titanium providing a constantly fresh surface. Sticking probability s=1 for N2 and mean thermal velocity = 470m/s. Find the pumping speed.

A getter screen consists of a cylinder of length l = 0.3m, diameter d=0.25m and its circular based plate. The getter screen is cooled with liquid nitrogen and coated completely with deposited titanium providing a constantly fresh surface. Sticking probability s=1 for N2 and mean thermal velocity = 470m/s. Find the pumping speed.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter6: Forced Convection Over Exterior Surfaces

Section: Chapter Questions

Problem 6.15P

See similar textbooks

Similar questions

You are designing a bioreactor that requires turbulent water flow (Re=2300) for better mixing of materials. Your tube diameter is 1.5 inches. What is the minimum volumetric flow rate needed (in in3/s)? **Answer: 7.14 in^3/s
The friction loss in laminar flow can be calculated using ____________ A. P.K Swammee and A.K. Jain Equation B. Darcy's equation C. Hazen-Williams Equation D. Hagen-Poiseuille equation
A pump is installed with a suction pipe of 200mm and a delivery pipe of 150mm (λ=0.02) in diameter to pump 0.08m3/s. The delivery pipe is 280m long. The elevation difference between the supply reservoir and the receiving reservoir is 20m. The cavitation parameter σ is 0.12 and the installation suffers a loss of 1.4m loss in the suction side. Determine the allowable height between the pump intake and the water surface elevation in the supply tank. The atmospheric pressure is 101.35kPa and the vapor pressure is 1.79kPa.
Piping system has pipes that are 130ft of 2inch inner diameter, 62ft of 5inch inner diameter, and 150ft of 3inch inner diameter. The water flows out at 20 degree C with a flow rate of 0.16ft^3/s (denisty of water is 1.936 slug/ft^3 and velocity is 1*10^-5ft^2/s) pressure drop including major losses now d o the same but only minor losses
Read the question carefully and give me all right solutios. A 2.4 m diameter tank is initially filled with water 5.5 m above the center of a 10 cm diameter, sharp-edged hole. The surface of the water tank is open to the atmosphere, and the hole drains to the atmosphere. If you neglect the effect of the kinetic energy correction factor, calculate: a) the initial flow rate of the tank and b) the time it takes to empty the tank.c) Does the orifice loss coefficient cause a significant increase in tank drain time? yes or no, the emptying time for this case is t =
A 1.0 m radius cylindrical industrial tank filled with viscous oil to a level at a height h from its base, must be drained through a tube with a radius of 0.2 m and length L, connected to its base. The speed profile of oil in the drain tube can be described by the equation below. Where v is the oil speed, vmax is a = maximum oil speed, r is the radius, and R is the tube radius. Considering this problem situation, do what is asked in the following items, justifying your answers. a) What is the volume, in liters, of oil removed from the tank after 10 seconds, if the maximum discharge speed does the oil reach 0.35 m/s? Data: π ≈ 22/7; 1 m3 = 1000 L. b) What flow regime does the system operate? Demonstrate. Data: specific mass of oil = 800 kg/m3, specific mass of water = 1000 kg/m3, oil viscosity = 0.056 Pa.s e viscosity of water = 0.001 Pa.s.
Pressure Drop of Power-Law Fluid in Laminar FlowA power-law fluid having a density of 1041 kg/m3 is flowing through 14.9 m of a tubing with an inside diameter of 0.0524 m at an average velocity of 0.0728 m/s. The rheological or flow properties of the fluid are K′ = 15.23N·sn′/m2 (0.318 lbf·sn′/ft2) and n′ = 0.40. Calculate the pressure drop and friction loss using Eq. (9.1-10) for laminar flow. Check the generalized Reynolds number to make sure that the flow is laminar. Repeat part (a) but use the friction-factor method
A 230-m-long pipeline delivers 20◦C water to a storage reservoir located downstream. The pipeline is galva-nized with an average roughness height of 0.2 mm. An axial pump is used to pressurize upstream water. Thewater surface in the reservoir is located 18 m above the centerline of the pump. The pump discharges waterat an absolute pressure of 400 kPa and a volume flow rate of 50 L/s. Calculate a diameter of pipe requiredto achieve such an operating condition. If needed, use the Moody diagram on the last page, or one can solvethe Colebrook equation using, for example, Matlab.
Find the draft loss in rectangular breeching 2.59m x 3.67m x 30.48m long when 196 m3/sec flue gas of 0.769 kg/m3 density are flowing.
Water at 20 degree C is pumped at a constant rate of 9 m3/h from a large reservoir resting on the floor to the open top of an experimental absorption tower. The point of discharge is 5m above the floor and friction losses in the 50 mm pipe from the reservoir to the tower amount to 2.5 J/Kg. At what height in the reservoir must the water level be kept if the pump can deliver only 0.1 K.W?
Q.3 A firm produces frozen fruits and vegetables, and a venturimeter is used in this process.In a certain step of the process, the cherries are introduced to the cold air stream at -12oC with a 3 in. pipe connected vertically to the throat of the venturimeter. Venturimeter is connected to a pipe 4 in. in diameter. If the air velocity in the throat is 5 times the terminal velocity of the cherries and the ratio of throat/pipe diameter is 0.6, what should be the flow rate of air? Assume that the density of cherries is 1200 kg/m3 and the average diameters are 12 mm. What should be the lay-out of the pipeline between venturimeter and freeze-dryer to prevent the striking of the cherries to the walls? Is there any settling possibility of the cherries at the exit of the venturimeter?
If the actual draft required for a furnace is 6.239 cm of water and the frictional losses in the stack are 15% of the theoretical draft, calculate the required stack height in meters, the velocity of flue gas, and the diameter of the stack for 43.9 kg/s of flue gas produced. Assume that the flue gas has an average temperature of 149 ℃ and MW of 30. Assume an air temperature of 21 ℃.