A given FM transmitter is modulated withsinusoidal input m(t) = 9 cos 500nt volts,and the modulation index is 5.5, and theunmodulated carrier power is 10W across520 resistive load. Determine:(a) the modulation sensitivity kp.(b) the load power.(c) The ratio of the power in the sum of the 3rdand 4th order sidebands to the power in allsidebands.(d) The required channel bandwidth for thetransmitted signal.

As per the rules we can answer only 3 sub-parts, please post the remaining sub-parts as the separate…

A given FM transmitter is modulated with sinusoidal input m(t) = 9 cos 500nt volts, and the modulation index is 5.5, and the unmodulated carrier power is 10W across 52N resistive load. Determine: (a) the modulation sensitivity kf. (b) the load power. (c) The ratio of the power in the sum of the 3rd and 4th order sidebands to the power in all sidebands.

A given FM transmitter is modulated with sinusoidal input m(t) = 9 cos 500nt volts, and the modulation index is 5.5, and the unmodulated carrier power is 10W across 52N resistive load. Determine: (a) the modulation sensitivity kf. (b) the load power. (c) The ratio of the power in the sum of the 3rd and 4th order sidebands to the power in all sidebands.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

5. The following data is available: fc= carrier frequency = 750kHz, Ac= maximum amplitude of the unmodulated carrier = 10V fm= modulator frequency = 300Hz-8kHz modulation index m=0.5 a) What is the frequency of the upper sideband? b) What is the frequency of the lower sideband? c) What is the amplitude of the modulating signal? d) What is the maximum amplitude of the envelope of the modulated signal? e) What is the minimum amplitude of the envelope of the modulated signal? f) What is the bandwidth of the modulated wave? g) Write an expression for the modulated wave
Applying Amplitude Modulation Double Sideband Large Carrier (AM DSB-LC) results in a modulated carrier signal bandwidth approximately two times greater than the baseband signal bandwidth (fm). True False
Use Carson’s rule to determine the bandwidth of an FM channel when the maximum deviation allowed is 5 kHz at frequencies up to 3.333 kHz. Sketch the spectrum, showing carrier and sideband values.
For double sideband (DSB) signala) Write the time domain equation XDSB(t).b) Write the frequency domain equation XDSB(ω).c) Draw the block diagram for DSB signal Generation.d) Draw the receiver block diagram. e) Explain with drawing the demodulation process of double sideband (DSB) signal using coherent detector.f) What is the difficulty of synchronous demodulation (coherent detection)? g) Compare between the ordinary amplitude modulation (AM), and double sideband (DSB) modulation in terms of transmitted power, complexity of demodulation, receiver cost, and bandwidth
An FM transmitter is determined to have a transmitter sensitivity of 498.716Hz/V. If the modulating signal is designed to be 15.998V, and the modulation index is kept to be at 1.5, solve for the highest upper sideband frequency in MHz considering that the carrier signal has a frequency equal to 172.255MHz.
q/A given AM (DSB – LC) transmitter develops an unmodulated power outputof 1 kW. Across 50Ω resistive load. When a sinusoidal test tone with a peakamplitude of 5? is applied to the input of the modulator, it is found that thespectral line for each sideband in the magnitude spectrum for the output is 40%of the carrier line. Determine the following quantities in the output signal:a-The modulation index.b-The peak amplitude of the lower sideband.c-The ratio of total sideband power to carrier power.d-The total output power.e-The total average power in thr output if the peak amplitude of the modulationsinusoid is reduced to 4 volt.
1. For a system with FM modulation, the amplitude of the unmodulated carrier is 12Vp, if the modulation index is 1.5 and the load resistance RL is 10 ohms,a) determine the power in the unmodulated carrier; b) Determine the power at the carrier frequency and at each significant side frequency for the modulated wave. What value of power do you obtain when adding the values obtained in question (b)?
Q1 ] A carrier signal ( peak amplitude = 39V , frequency = 100MHz ) frequency modulated by the baseband signal ( peak amplitude = 5V , bandwidth = 12.02kHz ) . The frequency deviation is 77.53kHz , and the load is 5112. Determine ( a ) the load power , ( b ) the bandwidth of the transmitted signal . ( consider only IJn ( $ ) > 0.1 ) .
What is the maximum average output power of a single-sideband signal (SSB) transmitter rated at 250 W peak envelope power (PEP)? W
5. Why must modulated signals be demodulated?A. To recover the original intelligenceB. To improve the spectral efficiency of digital transmissionsC. To enable implementation of advanced featuresD. To produce one or more significant sideband pairs
Type your question here An AM modulation waveform signal: ?(?) = (1 + 0.5 cos 2000?? + 0.5 cos 4000??) cos 20000?? (a) Sketch the amplitude spectrum of ?(?). (b) Find total power, sideband power and power efficiency (c) Find the average power containing of each sideband. (d) What is the modulation index?
Calculate the first two pairs of sidebands for an FM signal, if the carrier frequency is 107MHz, and modulating signal frequency is 3kHz