A given model is used to study the deformation of a polymer at E2 = 100 MPa, n1*= 500 MPa.s and n2*= 400 MPa.s Please plot the stress and relaxation versus time response when: a) a strain of 1.5 applied to the model for 100 seconds b) the stress behavior for the next 100 seconds after the strain is removed.

A given model is used to study the deformation of a polymer at E2 = 100 MPa, n1= 500 MPa.s and n2= 400 MPa.s Please plot the stress and relaxation versus time response when: a) a strain of 1.5 applied to the model for 100 seconds b) the stress behavior for the next 100 seconds after the strain is removed.

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter3: Transient Heat Conduction

Section: Chapter Questions

Problem 3.4P

See similar textbooks

Similar questions

A tensile test is conducted on a mild steel bar. The following data was obtained from the test : diameter of the steel bar= 3cm, Gauge Length of the bar = 20cm, Load at Elastic limit= 250kN, Extension at a load of 150kN= 0.21 mm, Maximum Load = 380kN, Total Extension= 60mm, Diameter of the rod at failure=2.25cm, determine young's modulus?
A band of polyisoprene is to hold together a bundle of steel rods for up to 1 year (52 weeks). If the stress on the band is less than 10MPa at that stage, the band will not hold the rods tightly any longer. Determine the initial stress that must be applied to the polyisoprene band when it is slipped over the steel. A series of tests showed that an initial stress of 7MPa decreased to 6.8MPa after 6 weeks. In a simple model, the rate at which stress relaxation occurs in elastomers is related to the relaxation time λ, which is considered a property of the elastomer. The stress after time t, is given by σ = σoexp(-t/λ) where σo = original stress A. None of the mentioned B. σ = 11.73 MPa C. σ = 10.29 MPa D. σ = 13.03 MPa
Give an approximate value for the tensile strength of a Boron/Aluminum composite with Vf = 0.4. Aluminum 2024 has E = 71 GPa, Poisson = 0.334, yield strength Sy = 76 MPa, strain-to-failure Ey = 22%. Boron fibers have E = 400 GPa, strength = 3.4 GPa, Poisson = 0.25. a. Compute F1t, assuming the Aluminum matrix remains elastic up to failure. If the value found is larger than Sy, the matrix yields, thus invalidating the assumption. b. Recompute using O1 = VfOf + (1 - Vf)Om c. Check that the strain-to-failure is not exceeded.
. An elliptical hair, 10.0 cm long, has the following semi-diameters A = 35\mu , B=25 \mu When the hair was extended from 10.0 cm to 10.1 cm at 50% RH the force on the hair increased by 11.3 grams. What is the modulus of elasticity in GPa, (round off) Group of answer choices 10.0 1.0 8.0 4.0
For a piece of copper alloy, a standard stress test was applied to it, the following data was collected, from which a stress-strain diagram must be generated, where as data it is known that the initial diameter of the element is 0.505in. The analysis must include the following: 1.Modulus of Elasticity and modulus of resilience. 2.Percentage of elongation. 3.Percentage of area reduction. 4.Real and engineering stress at fracture. It is known that after the specimen fractures, its dimensions in terms of length and diameter are 3.014 and 0.374in, respectively.
A sectional steel cable of 3.00 cm2 has a mass of 2.40 kg per meter. If the cable is 500 m long hanging on a vertical cliff, how far the cable is stretched due to weighs itself? Known young steel modulus 2.00 x 10¹¹ N/m2 . (b). If there are two climbers hanging on the cable, determine how far cable is stretched. The mass of climbers is 60 kg and 70 kg, respectively.
Suppose Polymethylmethacrylate (PMMA) and Polydimethylsiloxane (PDMS) have undergone tensile tests of similar settings at normal temperature and pressure conditions. With aid of a sketch, contrast their stress-strain responses.
(d) Figure Q2 (d) shows a typical aluminum stress-strain curve. A mechanical engineer has to carry out a tensile test for a rod of aluminum that can withstand an applied force of 20kN. To ensure safety, the maximum allowable stress on the rod is limited to 400 MPa, which is below the yield strength of the aluminum. The rod must be at least 380 cm long and must deform elastically not more than 0.8 cm when the force is applied. Design the appropriate rod.
A computer is protected against impact by foam packaging (spring stiffness, k = 100 N/cm; mass, m = 11 kg, including packaging). The maximum acceleration that the computer can withstand on impact with a hard surface is 4g. At the maximum acceptable impact acceleration, how much does the packaging compress upon impact? Give the answer in cm. What is the maximum height, h, in cm that the case can fall from without damaging the computer?
Mild steel 1 Young;s modulus 1219.5 Yield strain and stress (0.4101,500.08) Failure stress and strain :not able to find because the given data shows the experiment did not reach the failure point. if the material stress and strain does not reach a failure point ,what dose it means , does it means that the material is more stronger?
Find the total toughness energy for a metal that experiences both elastic and plastic deformations. The modulus of elasticity is 107.2 GPa, and elastic deformation terminates at a strain of 0.009. For plastic deformation, assume that the relationship between stress and strain is described by T = 1.66xKn, in which the values for K and n are 1453 MPa and 0.175, respectively. Furthermore, plastic deformation occurs between strain values of 0.009 and 0.67, at which point fracture occurs
Sintered silicon nitride parts are expected to experience tensile stresses 50% of the ultimate tensile strength of the material. What will be the maximum allowable size of internal flaws for these parts not to fail in service? Given the following properties of the material: Specific surface energy: 0.3 J/m2 its Youngs Modulus: 304 GPa Ultimate tensile Strength: 570 MPa Select one: a. 1.43 µm b. 0.71 µm c. 15 µm d. 85 µm e. 9.5 µm