QI/ If the thermal shock resistance of RBSN is 2214 w/m, poission ratio= 0.2 , cofficient of expansion= 2.6 x 10 /k, thermal conductivity=9 w/ m.k, specific heat= 0.86 j/ g.k ,thermal diffusivity= 4.4 x10 m /s, modulus of elasticity = 200 Gpa Calculate : 1.fracture streangth in Mpa 2. the density in Mpa 3. the thermal shock resistance in m' k/ s

QI/ If the thermal shock resistance of RBSN is 2214 w/m, poission ratio= 0.2 , cofficient of expansion= 2.6 x 10 /k, thermal conductivity=9 w/ m.k, specific heat= 0.86 j/ g.k ,thermal diffusivity= 4.4 x10 m /s, modulus of elasticity = 200 Gpa Calculate : 1.fracture streangth in Mpa 2. the density in Mpa 3. the thermal shock resistance in m' k/ s

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

At what value of poisson’s ratio young modulus is equivalent to shear modulus?
The compressive strength of alumina quartz (Al2O3) is 2.1 GPa. A quartz tube is being used for a vacuum furnace. Both ends of the tube are constrained and cannot move. To what temperature can the tube be heated up from room temperature such that the tube won’t fracture due to the thermal stress?
8.a) Calculate the theoretical fracture strength of a brittle material wherein fracture occurs by propagation of an elliptically shaped 0.25 mm surface crack with a 1.2 × 10-3 mm tip radius under an applied 1200 MPa stress. b) If the specific surface energy for a material is 0.30 J/m2 and its elastic modulus is 69 GPa, calculate the minimum stress required for propagation of a surface crack 0.05 mm in length. Based on this calculation, estimate the materials fracture toughness.
A 2-cm-long through thickness crack is discovered in a steel plate. If the plate experiences a stress of 50 MPa that is repeated at a frequency of 30 cpm, how long would it take to grow a crack, corresponding to the design limit where Klimit = KIC/3? Assume that KIC = 90 MPa √m and the material possesses a growth rate relation where da/dN = 4 x 10-37 ΔK4, with da/dN and ΔK being given in units of m/cycle and Pa √m , respectively
Can Young’s modulus have a negative value? What about the bulk modulus?
Alplas Plastics uses an extruder in which the barrel diameter = 0.4 m and length = 6.0 m. The extruder screw rotates at 65 rev/min; it has channel depth = 0.02 m and flight angle = 16°. The plastic melt has a shear viscosity = 85 Pa-s. Determine: (a) Qmax and pmax; (b) the shape factor Ks for a circular die opening in which Dd = 0.009 m and Ld = 0.03 m; and (c) the values of Q and p at the operating point
What is the maximum value of KIc as per LEFM that can be determined from experiments on a 20 mm thick plate? yield strength= 500 MPa, E= 210 GPa, poission ratio=0.3.
What are the importance of fracture toughness (KIC) and fatigue crack growthrate (da/dN) in design?
To manufacture a piston with a circular cross section, an alloy steel bar is required whose length is fixed and has a value of 35 cm and must withstand a compression load of 5.2 tons. For its design, a safety factor of 4/5 is suggested with respect to the yield stress. The shear modulus for 1)During an accident, the piston rod receives an impact with an energy of 250 kJ / m³. Is the bar deformedelastically, plastically or does it fracture? justify your answer
whwhat are the methods in solving mechanical vibration in damping elements enumrate
Turkey is to be sliced for a sandwich meat packaging company. A block of the turkey has a bottom surface of 12 cm x 9 cm. The block is held securely in a meat slicing machine. A slicing blade moves across the top surface of the turkey with a uniform lateral force of 28 N and slices a thin portion from the block. The shear modulus, G, of the turkey is 31.0 kPa. Estimate the deflection of the top surface with respect to the bottom surface of the block during slicing.
Calculate the young’s modulus from one of these two graphs?