a- Given the following screenshot, some errors are preventing PC-C from accessing the Redundant Internet Connection. Find the errors and correct them. Router0(config)# ip route 0.0.0.0 0.0.0.0 209.0.0.1 Router1(config)# router rip Router0(config)# router rip Router1(config-router)# passive-interface s0/0/1 Router0(config-router)# network 172.16.1.4 Router1(config-router)# network 172.16.1.0 Router0(config-router)# auto-summary Router1(config-router)# no auto-summary Your answer b- After correcting the errors, PC-C is able to reach the Primary Internet. Which command is used to view the routing table on Router 1?*

a- Given the following screenshot, some errors are preventing PC-C from accessing the Redundant Internet Connection. Find the errors and correct them. Router0(config)# ip route 0.0.0.0 0.0.0.0 209.0.0.1 Router1(config)# router rip Router0(config)# router rip Router1(config-router)# passive-interface s0/0/1 Router0(config-router)# network 172.16.1.4 Router1(config-router)# network 172.16.1.0 Router0(config-router)# auto-summary Router1(config-router)# no auto-summary Your answer b- After correcting the errors, PC-C is able to reach the Primary Internet. Which command is used to view the routing table on Router 1?*

A+ Guide To It Technical Support

10th Edition

ISBN:9780357108291

Author:ANDREWS, Jean.

Publisher:ANDREWS, Jean.

Chapter9: Supporting Mobile Devices

Section: Chapter Questions

Problem 17TC

See similar textbooks

Similar questions

Use given Figure 1 to configure a two-router network. All router configurations must be assumed and done using a PC connected to the router’s console port through its RS232 serial port. Configure all interfaces of ONLY Router A. Please write all necessary commands/RIP version etc.
ARP is necessary for the communication amongst the Hosts, justify this statement. Look at the following bits of ARP and clearly mention Source MAC Address, Destination MAC address, Type of ARP, Source IP & Target IP
Explain in detail how a computer technician would go about statically setting up theIPv4 address 192.168.10.25 in Windows 10 with its default subnet mask and a Router and DNS address of 192.168.10.2
Assume that the Ethernet Switch Forwarding table (MAC Address Table) starts out empty, and then Client #2 sends a packet to Client #3 and then Client #3 sends a reply packet back to Client #2. After these packet transmissions are done, show me the contents of the Forwarding Table of the Ethernet Switch. There are 3 switch ports, named Fa0, Fa1, Fa2. MAC Address: 1. 2. Switch Port: 1. 2.
Is it possible to utilize one Media Access Control (MAC) address for several network interfaces? Possibly? Is it possible to utilize one IP address on several network interfaces? Possibly?
Is it true that a router will only route MAC addresses and no other addresses? For those who said yes, please describe the equipment you're referring to, and for those who answered no, please describe how it operates.
Suppose you open your BMCC mailbox first thing on a Monday morning and find that your messages have arrived. Assuming the BMCC server does not have access to the MAC address of the device reading these emails. Explain in detail how the ARP protocol determines which device on the LAN will be the recipient of incoming Internet data. After 22 years, the transition to IPv6 addressing is complete for around 30 percent of Internet traffic. When comparing IPv4 and IPv6 address headers, the Ethernet frames' Maximum Transmission Unit (MTU) stands out as a potential stumbling block.
ICMP is used for addressing error reporting routing forwarding Which of the following is an example of a private IP address? 12.127.18 65.20.10 169.200.224 100.20.2 ARP provides a mapping between IP addresses and MAC Addresses Domain Names Phone Numbers Network Addresses
DIRECTION. Perform the following tasks and capture or copy the CLI commands for each indicated task. Task 1. Create VLAN’s, enable switchport mode, and assigning VLAN’s interfaces on each switch. Task 2. Configure sub-interfaces on a router with CME Task 3. Configuring a DHCP address scope on a Router Task 4. Configure Router’s Telephony Service for IP Phone Task 5. Create Directory Numbers Task 6. Verify Connectivity and Test IP Phone Communication Please show me the step by step
Question 4: (17 marks) From the MAC address 4E:A2:C6:BB:D9:C8 determine the IPv6 address Interface ID of the IPV6 address using the EUI-64 process. Answer the following questions related to Frame forwarding. (4 marks) Figure B Refer to figure B and identify the port(s) where the switch should forwards the frame. (2 marks) When the switch forwards the frame, determine which statement(s) are true and which are false? (2 marks) a) Switch add the source MAC address which is currently not in the MAC address table. b) Frame is a broadcast frame and will be forwarded to all ports. c) Frame is a unicast frame and will be sent to specific port only. d) Frame is a unicast frame and will be flooded to all ports. Inter-VLAN routing can be achieved via different ways: Legacy Inter-VLAN routing Router on a stick Layer 3 switch using Switched Virtual Interfaces “SVIs” Write s short report (200 words max), using your own…
May someone please show me what should I input in the CLI in every task/ DIRECTION. Perform the following tasks and capture or copy the CLI commands for each indicated task. Task 1. Create VLAN’s, enable switchport mode, and assigning VLAN’s interfaces on each switch. Task 2. Configure sub-interfaces on a router with CME Task 3. Configuring a DHCP address scope on a Router Task 4. Configure Router’s Telephony Service for IP Phone Task 5. Create Directory Numbers Task 6. Verify Connectivity and Test IP Phone Communication
QUESTION 67 Explain what happen in the following scenario in TCP A sends the first segment to B (successfully delivered) A sends the second segment to B (successfully delivered) B sends the ACK for the first segment (dropped) B sends the ACK for the second segment (successfully delivered) QUESTION 68 What is the need to IP address? why not to simply use MAC addresses?