A guitar string has a diameter of 0.33 mm and is made of steel, p=7000 kg/m3. The string is tuned to a fundamental frequency of 329.33 Hz. The string has a length of 0.8 m. Assume the string is fixed at both ends. a) What is the tension in the guitar string? b) What is the wave speed in the string at this tension? c) What are the frequencies of the 2nd and 3rd harmonics?

A guitar string has a diameter of 0.33 mm and is made of steel, p=7000 kg/m3. The string is tuned to a fundamental frequency of 329.33 Hz. The string has a length of 0.8 m. Assume the string is fixed at both ends. a) What is the tension in the guitar string? b) What is the wave speed in the string at this tension? c) What are the frequencies of the 2nd and 3rd harmonics?

Name: A guitar string has a diameter of 0.33 mm and is madeof steel, p=7000
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A guitar string has a diameter of 0.33 mm and is madeof steel, p=7000 kg/m3. The string is tuned to afundamental frequency of 329.33 Hz. The string has alength of 0.8 m. Assume the string is fixed at bothends. a) What is the tension in the guitar st

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The blood pressure in your heart is 1.52 x104 Pa. If an artery in the brain is 0.421 m above the heart, what is the pressure in the artery?
1. discuss the effect of changing the damper location on the threshold length for (vibration amplitude, natural frequency, damping coefficient, damping ratio) .2- what happens if the damping fluid type is changed (air, water, high density oil)?
A flexible string 1.0 m long is connected to an oscillator. When the oscillator is set to vibrate the string at 100Hz, a standing wave is formed in the fundamental mode of oscillation. What is the speed of waves on the string?
In the experiment on the spring-mass system, a mass of 1.8 kg is applied and the stiffness (k) of the spring is 207 N/m. Find the natural frequency () of the spring-mass system in rad/sec and the deflection of the spring (?) in mm.
A Jello desert resting on a plate is starts wiggling when it is sheared to the side 0.5 cm as is set on the table. The desert is a rectangular prism with a square face 25.0-cm on a side and a height of 12.0 cm. A quick Google search reveals that the density of Jello is 1140 kg/m3 with shear modulus of 530 N/m2. What is its rate of oscillation? If the energy of oscillation is dissipated at the rate of 5.00 x 10-5 J per second how long will the block wiggle?
1) An electric motor’s torque is a function of the speed at which it rotates. Many brushed AC motors have a linear toque curve as shown below. If the power output of the motor is equal to the torque (T) multiplied by the rotational speed in rad/s (w), what is the maximum power you can get out of the motor if the stall torque (Tstall) is 0.001 Nm and the no load speed (wno load) of 10,500 RPM? Give answer in Watts.
spring attached 2.00 kg block is stretched 20.0cm and released from rest on a frictionless surface. The measured period is 1.00 sec. a) What is the spring constant k? b)A student doubled the stretched length. what is the period of the spring? c) You want to make a simple pendulum and a physical pendulum which is a uniform bar, and you want same period with the spring’s period, 1.00sec. Determine the length of simple pendulum (Ls) and physical pendulum (Lp). And find the ratio of their length (Lp/Ls). d) If you doubled the length of the simple pendulum and physical pendulum, what is the period of each pendulum? e)You take these three harmonic oscillatorsto the space station and measure the period. Describe what the measured value of the period of each oscillator would be.Why?
Answers (a) er=15.30-250.2/r^2 , etheta=15.30+250.2/r^2 (b) delta c = 8.12x10^-4 in
As shown in the figure below, a string attached to a vertical wall passes over a pulley at the end of a horizontal rod, and supports a sphere. The horizontal rod has a length L = 0.320 m, the mass of the sphere is M = 1.20 kg, the string makes an angle ? = 38.0° with the rod, and, when the string is plucked, the fundamental frequency of standing waves in the portion of the string above the rod is f = 70.0 Hz. Determine the mass of the portion of the string above the rod (in g). Answer:___________ g
5.3. Plot the variation of Ex, Gxy, νxy, mx, and my for a lamina with the following properties: EL = 35 GPa ET = 3.5 GPa GLT = 4 GPa νLT = 0.45 (Please type answer no write by hend)
PROPAGATION OF ERROR You are tasked to supervise the design of 0.5MW wind turbine to be constructed in a Wind Farm in Pililla, Rizal. Suppose the design criteria are as follows: The air density as surveyed after 2 year period averaged at 1.225 kg / cubic meter. The sweeping diameter of the rotor blades is 125m, and the anemometer reading in the area amounts to 4.2m/s on a 2 year period of survey. What is the theoretical power output of the turbine assuming 100% efficiency of operation? Your answer must be in kW and in two decimal places with correct signs. In the previous problem, if the diameter measurement is off by 0.1m and the anemometer reading is also fluctuating by 0.05m/s and if the error measurement for theoretical power output must be limited to 3%, WHY OR WHY NOT should you accept the design? * Show complete solution in paper.
In the figure below, a string tied over a support at Q, is stretched by a block of mass m. Separation L = 1.20 m, linear density μ = 1.6 g/m, ant the oscillator frequency f = 120.0 Hz. Assume P and Q are nodes. What mass m allows the oscillator to set up the fourth harmonic on the string? Determine the wavelength based upon the length and the number of waves shown in the figure. Then, determine the required tension required to achieve the necessary velocity v=λf and v=(T/μ)0.5. Then determine the mass necessary to achieve this tension. T = mg. Use g = 10 N/kg.