A heavy ring moulding of diameter 2m is supported by six steel cables of equal lengths and attached at the points spaced uniformly along the circumference of the ring. The moulding weighs 2.5kN/m. See Figure AS- ST50. 96. Find the tension in each steel wire. a. 2.62 kN b. 2.76 kN c. 2.83 kN d. 2.89 kN

A heavy ring moulding of diameter 2m is supported by six steel cables of equal lengths and attached at the points spaced uniformly along the circumference of the ring. The moulding weighs 2.5kN/m. See Figure AS- ST50. 96. Find the tension in each steel wire. a. 2.62 kN b. 2.76 kN c. 2.83 kN d. 2.89 kN

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate and draw the internal forces created at H section of the bracket beam? a = 500 mm b= 200 mm Px= 15 Kn Py=0 Kn Pz = 10 Kn
Find the Maximum Shear andMoment.? can you solve in 20 mins?
Compute the value of EI ϴ at the right end support. Wo = 14 kN/m, P =5 kN, L1 = 1.1m, L2 = 2.1m, L3 = 2.3m
A steel bar having cross-sectional areaA=1200mm2 is compressed by an axial loadP=53 kN.Determine the average normal and shear stressesacting on aninclined sectionaa cut through the bar at angleα=250.(Point K is a fixed support) A=5, B=3, C=8
1. Find the resultant of tension F and Ta. 27.6 kNb. 37.2 kNc. 33.7 kNd. 44.6 kN2. What is the angle that their resultant makes with the horizontal rod OA? a. 28 degb. 37 degc. 33 degd. 44 deg3. Find the weight, W to prevent uplift. Use a factor of safety of 2.5. a. 49.23 kNb. 42.86 kNc. 59.51 kNd. 44.72 kN
What is the moment of the distributed load about the pin O? (a) 473 kN-m clockwise.(b) 338 kN-m clockwise.(c) 338 kN-m counterclockwise.(d) 270 kN-m counterclockwise.
The Channel section is used as a purlin placed on top of trusses with spacing of 4 m and slope 1V to 4H. The purling are supporting a total uniform load of 24 kN/m. Properties of Channel: Sx = 119 x 10^3 mm^3 Sy = 87 x 10^3 mm^3 Compute the maximum bending stress if supported by sagrods at third points. Round your answer to 2 decimal places.
Determine support reaction. Given a=5 m b=10 m P=30 KN
Determine the magnitude of the moment of force F about segmentOA of the pipe assembly shown.
Determine the vertical and horizontal displace-ments at A of the pin-connected structure in Figure P9.31.Given: E = 200 GPa and A = 500 mm2for all members.
Write legibly and box the final answer. Determine the maximum mass (kg) that can be lifted at E if the 11.670-HP motor A has a maximum rotation speed of 301.20 rpm where the diameter of the shaft AB and CE are 10.237 mm and 15.402 mm, respectively. The allowable shearing stress is 1.001 GPa with F.S. of 1.76 for both shafts. Neglect the deformation of the cable at E. Where: radius of the gear at B, rB = 113.10 mm radius of the gear at C, rc = 158.58 mm
a steel plate 2.7 m x 1.3 m x 100 mm thick is to be hoisted by a steel cable sling. assume the steel weighs 77.3 kN/cu.m. 1. determine the shear stress (MPa) in the 18 mm diameter pins through the clevis