A helical compression spring has a scale of 500 lb/in., an outside diameter of 2.75 in, a free length of 8 inches and with squared and ground ends. The load is 1,000 lbs and the working stress on the wire material is 65000 psi. If the Wahl factor of 1.25 is to be used, calculate the following: A. The standard wire diameter B. The number of active coil if G = 10 800 000 psi C. The solid height D. The stress at solid height

A helical compression spring has a scale of 500 lb/in., an outside diameter of 2.75 in, a free length of 8 inches and with squared and ground ends. The load is 1,000 lbs and the working stress on the wire material is 65000 psi. If the Wahl factor of 1.25 is to be used, calculate the following: A. The standard wire diameter B. The number of active coil if G = 10 800 000 psi C. The solid height D. The stress at solid height

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter2: Axially Loaded Members

Section: Chapter Questions

Problem 2.2.11P: A small lab scale has a rigid L-shaped frame ABC consisting of a horizontal arm AB (length b = 10...

See similar textbooks

Similar questions

A helical compression spring has a scale of 400 lbs/inch, an inside diameter of 2.5 inches, a free length of 8 inches and with squared and ground ends. Material is to be chrome vanadium steel. For a load P of 750 lbs and for the average service Determine the standard size wire diameter Determine the number of active coils Determine the solid height Determine the stress at solid height
A helical compression spring is 1o exert a force of 8.0 Ib when compressed 1o a length of 1.75 in. At a length of 1.25 in, the force must be 12.0 Ib. The spring will be installed in a machine that cycles slowly. and approximately 200 000 cycles total are expected. The tem- perature will not exceed 200°F. The spring will be installed in a hole having a diameter of 0.75 in. For this application. specify a suitable material, wire diameter. mean diameter. OD. ID. free length, solid length. number of coils, and type of end condition. Check the stress at the maximum operating load and at the solid length condition. The first of two solution procedures will be shown. The numbered steps can be used as a guide for future problems and as a Kind of algorithm for the spreadsheet approach that follows the manual solution.
PROBLEM:2 A spring made from a wire of 2.5 mm diameter and 750 N/sq. mm. as its working stress Mean diameter of 12.5 mm and 15 active coils. Find (a) Stiffness of the spring (b) solid length. Assume that the ends are squared and ground. Take modulus of rigidity as 0.85x105 N/mm2.
Find the number of active coils of a No. 10 wire Helical Spring index of 7, steady load with spring rate of 46.5 lb/in. maximum allowable stress is 70 ksi. The stiffness of a spring is 98 N/mm of axial compression. Find the Joules of work to increase the compression from 60 mm to 90 mm.
A helical compression spring with square and ground ends has an outside diameter of 14 mm, 20 total coils, a wire diameter of 2 mm, and a free length of 105 mm. Calculate the spring index, the pitch, the solid length, and the shear stress in the wire when the spring is compressed to its solid length.
A spring made from music wire ASTM 228 steel has the following data:Free length=1.75” Outside diameter=0.561”Wire diameter=0.055” Applied load= 14 lbEnds=square and ground both ends hingedNumber of coils=10 G=11.85 x 106psi E= 30 Mpsi Findspring rate, force at solid length,check for buckling,coil clearance and hole diameter
Design a helical compression spring to be used in a cam and follower mechanism made of oil tempered carbon steel, is subjected to a load which varies from 416 N to 950 N. The spring index is 6.7 and the design factor of safety is 1.25. If the yield stress in shear is 770 MPa and endurance stress in shear is 350 MPa,find: 1. Size of the spring wire, 2. Diameters of the spring, 3. Number of turns of the spring, and 4. Free length of the spring. The compression of the spring at the maximum load is 30 mm. The modulus of rigidity for the spring material may be taken as 80 kN/mm2.
(5) A gas engine valve spring is loaded to 35kgf when the valve is closed & 52kgf hen the valve is open. The valve lift is 8mm. The outside diameter is to be from 38mm~45mm, & the permissible stress is 413N/mm2 . Determine: (a) the wire & outside diameter; (b) the number of effective coils; (c) the free length when it is squared & ground.
Two coaxial closed coil springs make up a standard compound helical spring. When both springs are unloaded, they are not of equal length. If each spring's working stress is to be the same. The wire material has an 80 GPa modulus of rigidity. Find the diameter of steel wire for inner spring and stiffness of inner spring. Also find the stiffness of the compound spring. Outer spring a: Mean coil diameter = 100 mm No. of turns = 15 Wire diameter = 12.5 mm Inner spring b: mean coil diameter = 75 mm No. of turns = 20
A closed-coil helical spring is to have stiffness of 900 N/m in compression with a maximum load of 45 N and a maximum shearing stress of 120 N/mm2.The length of the spring is 45 mm. find the wire diameter, mean coil radius and the number of coils. Take C= 40000 N/mm2
A helical compression spring is to be used for a maximum load of 1.5 kN using the spring index of 8. The maximum permissible shear stress for the spring wire is 400 MPa. Which of the following is the wire diameter of the spring to be used?
A high alloy spring has an active coil of 16 and modulus ofelasticity in shear of 85 GPa. Compute the Wahl factor. Thespring outside diameter is 9.66 cm and wire diameter is 0.65 cm.