A historic bridge shows a deterioration in its structure. It will be restricted for vehicles weighing less than 1600 kg; otherwise it will be prevented access through a “feather” type barrier. To monitor the weight of the car are used 4 independent sensors placed on a platform just below the tires of the vehicle. Each sensor emits 1mV for every Kg. The weight of the car is the sum of the four sensors. Design a circuit that displays the weight of the car on a digital multimeter.

A historic bridge shows a deterioration in its structure. It will be restricted for vehicles weighing less than 1600 kg; otherwise it will be prevented access through a “feather” type barrier. To monitor the weight of the car are used 4 independent sensors placed on a platform just below the tires of the vehicle. Each sensor emits 1mV for every Kg. The weight of the car is the sum of the four sensors. Design a circuit that displays the weight of the car on a digital multimeter.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter33: Single-phase Motors

Section: Chapter Questions

Problem 1PA

See similar textbooks

Similar questions

Write an essay about combination and sequential circuits Your essay should among other things ; include a short introduction articulating the significance and applications of these circuits articulate the differences between the two types of circuits citing at least 3 examples for each category. Your essay should be extended to include and describe a Multiplexer(MUX) circuit citing how it works, Its application , and its truth table . You are to describe your truth table by explaining how each input relates to output
8.7 MECT361 Mechatronics Components and Instrumentation 8.7. Given a 12-bit A/D converter operating over a voltage range from - 5 V to 5 V, how much does the input voltage have to change, in general, in order to be detectable? PLEASE GIVE ME THE REFRENCE I Will get zero if you didn't put the refrence
Five elements are involved when a computer is monitoring andcontrolling a physical variable that is assumed to be analog.”Illustrate the above situation. this question regRDING Design cirecuits
The gate of a MOSFET transistor is initially uncharged. A voltage of 3V is applied starting at t = 0, causing a current to flow given by: I = 0.015exp(-106t) (a) What is the total charge delivered to the MOSFET gate for all time ( 0 < t < ∞ ). (b) What is the total energy delivered to the MOSFET gate for all time ( 0 < t < ∞ ).
2. (a) An electrocardiogram (ECG) is a recording of the electrical activity of theheart. When designing a microprocessor-based system the ECG is recordedusing analogue circuitry that is connected to a low-speed ADC. The ADC is,in turn, connected to a microprocessor and then to a laptop computer.Describe which interface standards you would propose for the followingconnections:(i) between the ADC and the microprocessor, and(ii) the connection between the microprocessor and the laptopcomputer.Your answers should include justifications for your proposals.(b) The system described in part (a) needs to be galvanically isolated in orderto ensure patient safety.(i) Explain the concept of galvanic isolation.(ii) Describe, by drawing schematics, how the interface you proposed inpart (a) between the ADC and the microprocessor could begalvanically isolated.(iii) Describe, by drawing schematics, how you might modify the logicvoltage levels between the ADC and the microprocessor if they donot operate…
using matlab, design a solar tracking system that maximizes the amount of solar energy captured by a single solar panel throughout the day. This system will consist of a microcontroller-based tracking device( eg arduino) that adjusts the position of the solar panel based on the position of the sun. The solar panel will be connected to a battery charging circuit that will charge a battery large enough to power an LED streetlight at night. The project will also involve designing a circuit that controls the LED streetlight, turning it on at night and off during the day
Q2. Design a digital circuit that indicates via an LED output whether a 4-bit unsigned number is a Lucas number (TRUE=1) or not (FALSE=0) (see Wikipedia). In this question, the input to the circuit should be assumed to be from a decimal keypad (0-9). Therefore, the behaviour of the circuit does not matter when then the input value is greater than 9. This should be taken advantage of in the design process. The steps are:(a) State the truth table for the circuit.(b) State the Karnaugh map for the circuit.(c) Group the 1-cells according to the Karnaugh map technique.
You are an electronic engineer who is working on the design, production and implementation of Digital electronic circuits for customers of an electronic company. You manager has given you two digital electronic circuits to analyse and explain their operations. You need to write a report for the manager so he can pass this on to the customers who will be using these circuits. The report should include a section for each circuit. You manager has asked you to write a report to a customer who will be using the following digital circuits that implement combinational circuits in their operation: A one bit full adder Within your report, You need to include in your report the truth table of the circuit and also need to use the Boolean Algebra/Karnaugh Map to minimise the number of gates used in the design and build of such circuits.
1. design a circuit for a digital lock that unlocks for all the even numbers put in as a 4-bit input. 2. to save electricity consumption design a circuit that only lets, at most, three out of four suction motors run at a time where to find these questions .
Given that a DAC-Weighted Resistor Network output consist of 4-bit which are controlled by 4 solid-state switches with operating voltage of 5 V. Calculate the resolution of the system.
Design a combinational circuit that will function as a Binary Divider. Itwill accept 2 inputs, x, and y, that are two bits each. It will generate as its outputthe integral quotient and a warning indicator for undefined quotients. Show yourcomplete solution.
Suppose a 10-bit DAC is built using the inherently monotonic circuit technique as shown. (a) If the resistor material has a sheet resistanceof 50 Ω/square, and R = 500 Ω, estimate the number of squares that will be required for the resistor string. (b) If the minimum width of a resistoris 2.5 μm, what is the required length of the resistor string? Convert this length to inches. 12.6 A