A hollow shaft with outside diameter of 165 mm and wall thickness of 8 mm transmits 192 kW at 400 rpm. What must be the angular deflection of the shaft in degrees if the length is 5 m? The material of the shaft has a shearing strength of 210 MPa. Let G = 11.5 x 106 psi.

A hollow shaft with outside diameter of 165 mm and wall thickness of 8 mm transmits 192 kW at 400 rpm. What must be the angular deflection of the shaft in degrees if the length is 5 m? The material of the shaft has a shearing strength of 210 MPa. Let G = 11.5 x 106 psi.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter3: Torsion

Section: Chapter Questions

Problem 3.3.12P: A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable...

See similar textbooks

Related questions

Q: A 1/2in diameter round steel rod 32ft long supports a load of 5kips. How much will it elongate?…

Q: A rectangular polypropylene [E = 6,200 MPa] bar (1) is connected to a rectangular nylon [ E = 1,400…

A: GIVEN DATA- Two bar connected at flange B For bar 1 A1=990mm2 , L1=1600mm , E1=6200MPa For bar 2…

Q: 40. Marbles on a Xylophone. A xylophone is made of several cuboidal keys of the same material Z,…

A: We can answer up to 3 subparts so we will answer first 3. Please resubmit the question by specifying…

Q: A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal…

Q: Problem 3 For the beam shown in the figure, a) Derive the equation of the elastic curve. b) Compute…

Q: 1. The following data were obtained on a gasoline engine operating in a pronymbrake. Engine speed:…

Q: Calculate the weight W of the aluminum casting shown. The solid is generated by revolving the…

Q: A steel [E = 29,200 ksi; a = 6.0 x 106/°F] pipe column (1) with a cross-sectional area of A₁ = 5.40…

Q: ABOCD are five points, in that order, in a straight line AD. AO=OD. A particle moving with SHM along…

Q: A pin-connected structure is supported and loaded as shown. Member ABCD is rigid and is horizontal…

Q: A copper [E = 104 GPa, a = 17.1x10-6/°C] rod (2) is placed within a steel [E = 208 GPa, a =…

Q: A 6-mm-diameter electrical transmission line carries an electric current of 50 amperes and has a…

A: Given- parameter given- diameter= 6mm current= 50A resistance= 0.002ohm/mt. length k=218w/m-k

Q: Three reservoirs are connected in a common junction. Following are the pertinent information:…

Q: b) Figure Q1b shows a compound gear train with Gear A as the pinion (or driver) with an input Power…

Q: Determine the x- and y-coordinates of the centroid of the shaded area. 45 45 x = y Answers: y = 175…

Q: A 1/2in diameter round steel rod 32ft long supports a load of 5kips. How much will it elongate?…

A: Given: Diameter of steel rod = d = 0.5 inch Length of steel rod = L = 32 ft. = 384 inch Load applied…

Q: A ball is shot vertically into the air at a velocity of 58 m/s. After 5 seconds, another ball is…

Q: A slab milling operation is performed to finish the top surface of a steel workpiece 250*75 mm*mm.…

Q: The 7.3 Kg block rests on the smooth incline. If the spring is originally stretched 80cm determine…

A: Given Data m=7.3 Kg s=3.2 m k=25N/m P=320N x1=80cm=0.8m Free Body Diagram according to the Question

Q: Calculate the y-coordinate of the centroid of the shaded area. 47 mm Answer: y = 2121 mm i mm 21 mm…

Q: A SOLID 1.8 IN. DIAMETER SHAFT IS UTILIZED TO SYNCHRONIZE MULTIPLE MECHANISMS IN THE MANUFACTURING…

A: Given: The diameter of the solid shaft is d=1.8 in. The torque delivered by the shaft is T=3500…

Q: Ductile failure is characterised by: Little or no elongation to failure Cavity coalescence…

A: Ductile fracture : It is fracture that happens when a material is subjected to a load for some time…

Q: Determine the vertical distance from the lower edge of the built-up wooden beam to the location of…

Q: Discuss the effect of Reynolds number on the thickness of boundary layer flows and the wall shear…

Q: For a powder binding process that mixes a 3:1 volume ratio mixture of semi-crystalline polyethylene…

A: Given data: The density of polyethylene in its amorphous state is, ρas=0.870 gcm3 The density of…

Q: The 30-kg reel is mounted on a 20 kg cart. The reel is free to rotate about the axle O. The radius…

A: Given- Mrecl=30kg. Mcart=20kg. Ko=250mm. P=50N t=4sec.

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

Q: 5.) Air is kept at a pressure of 135 MPa absolute and a temperature of 15 C in a 7000 ml container.…

Q: Calculate the normal stress in the copper rod if the temperature of the entire assembly is raised by…

Q: A 1/2in diameter round steel rod 32ft long supports a load of 5kips. How much will it elongate?…

A: Given data: ◆ The diameter of steel rod: d = 0.5 in ◆ The length of the steel rod: L = 32 ft = (32…

Q: Given in the figure, the wind forces are perpendicular with respect to the inclined member of truss.…

A: Given:- A truss Forces are perpendicular with respect to the inclined member of truss as shown in…

Q: VA A - S VB B

Q: A 2197 lb car starts from rest at point 1 and moves without friction down the track shown. Determine…

Q: The cross-sectional dimensions of a beam are shown. Assume by-3.25 in.. t-t-0.375 in. and d=4.875…

Q: Engineering Mechanics II A man shooting a ball to ring 19.68 ft high from the ground has a…

Q: A 50-cm X 30-cm X 20-cm block weighing 150 N is to be moved at a constant velocity of 0.80 m/s on an…

Q: In the figure, aluminum [E = 75 GPa] links (1) and (2) support rigid beam ABC. Link (1) has a…

Q: The composite simply supported steel shaft is subjected to a force of 2P2PP = 16 kNkN at its center.…

A: To find maximum deflection

Q: % Flowrate 100 90 80 70 60 40 30 20 10 0 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95…

A: This is a basic problem of Fluid Control Valve System Engineering(Fluid Mechanics). Based on the…

Q: A 1.16 kg block B is moving with a speed of 2.39 m/s as it strikes the 0.28 kg sphere A which was at…

A: Given data: ◆ The mass of the block B and it's initial velocity: mB = 1.16 kg , uB = Vo = 2.39 m/s ◆…

Q: If block A is intended to move vertically at a constant rate of 2.36m/s, determine the rate (m/s) at…

Q: L₁ Answer: vg: (1) i a B P b (2) mm. C L2

Q: The distance y = 2.8 m. Find the upward velocity of A if the downward velocity of B is 3.8 m/s.…

Q: Figure Q4a shows a water reservoir with a 20 m wide rectangular gate that is hinged at point A and…

A: Given:Width of the rectangular gate, w=20 mDepth of the water, H=10 mPosition of hinged A from the…

Q: Consider the following fluids at a film temperature of 300 K in parallel flow over a flat plate with…

A: Given: The temperature of fluid, T = 300 K The speed of fluid, v = 1 m/s The distance from leading…

Q: A beam cross section is shown. The dimensions are d - 10.2 in. and t= 0.46 in. The centroid of the…

Q: Determine the internal torques, T₁ and T2, in segments (1) and (2), respectively. Use the internal…

Q: A cable is wrapped around the spool's center hub. The mass of the spool is m= 100 kg, the radius r1…

Q: Determine the magnitude of the vertical force C, for the simply supported beam, where w=7 kips/ft,…

Q: surface is generated by revolving the circular arc of 0.8 m radius and subtended angle of 120…

A: The circumference of the arc is rotated about the z-axis. Hence the area generated can be found by…

Concept explainers

Combined Loading

Any functioning component, such as machine parts, structural members, pressure vessels, and so on, are all under the influence of more than one force. When anybody is under the influence of more than one force such as shear forces, bending moments, axial forces, torsion, and so on, then such body is said to be under combined loading. A very practical example of combined loading is the crankshaft of an internal combustion engine (IC engine). The crankshaft of the IC engine is under high rpm, which is caused due to the torsional forces. Due to the presence of piston, counterbalances, and internal imbalances, the crankshaft experiences lateral forces and due to the rise in temperature, the crankshaft undergoes thermal expansion, which pulls the crankshaft along the axial direction and lateral direction. The presence of unbalanced loads along the periphery of the crankshaft also induces a bending moment.

Question

A hollow shaft with outside diameter of 165 mm and wall thickness of 8 mm transmits
192 kW at 400 rpm. What must be the angular deflection of the shaft in degrees if the
length is 5 m? The material of the shaft has a shearing strength of 210 MPa. Let G = 11.5 x
106 psi.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A propeller shaft for a small yacht is made of a solid steel bar 104 mm in diameter. The allowable stress in shear is 48 MPa, and the allowable rate of twist is 2.0° in 3.5 meters. (a) Assuming that the shear modulus of elasticity is G = 80 GPa, determine the maximum torque that can be applied to the shaft. (b) Repeat part (a) if the shaft is now hollow with an inner diameter of 5d18. Compare values to corresponding values from part (a).
What is the maximum power that can be delivered by a hollow propeller shaft (outside diameter 50 mm, inside diameter 40 mm, and shear modulus of elasticity 80 GPa) turning at 600 rpm if the allowable shear stress is 100 MPa and the allowable rate of twist is 3.0°/m?
A circular tube AB is fixed at one end and free at the other. The tube is subjected to concentrated torques as shown in the figure. If the outer radius of the tube is 1.5 in, and the thickness is 3/4 in., calculate the strain energy stored in the tube. Let G= 11,800 ksi.
A thin-walled aluminum tube of rectangular cross section (sec fig me) has a centerline dimensions b = 6.0 in. and b = 4.0 in. The wall thickness t is constant and equal to 0.25 in. Determine the shear stress in the tube due to a torque T = 15 kip-in. Determine the angle of twist (in degrees) if the length L of the tube is 50 in. and the shear modulus G is 4.0 x 106 psi.
Two sections of steel drill pipe, joined by bolted flange plates at B, arc subjected to a concentrated torque 4000 kip-in. at x = 3 ft, and a uniformly distributed torque t0= 50 kip-ft/ft is applied on pipe BC. Let G = 11,800 ksi and assume that pipes AB and BC have the same inner diameter, d = 12 in. Pipe AB has a thickness tAB= 3/4 in., and pipe BC has a thickness tBC= 5/8 in. Find the reactive torques at A and C and the maximum shear stresses in each segment.
The stepped shaft shown in the figure is required to transmit 600 kW of power at 400 rpm. The shaft has a full quarter-circular fillet, and the smaller diameter D1= 100 mm. If the allowable shear stress at the stress concentration is 100 MPa, at what diameter will this stress be reached? Is this diameter an upper or a lower limit on the value of D2?
A stepped shaft ACB having solid circular cross sections with two different diameters is held against rotation at the ends (sec figure). If the allowable shear stress in the shaft is 6000 psi, what is the maximum torque (T0) that may be applied at section C? Find (T0)max if the maximum angle of twist is limited to 0.55º. Let G = 10,600 ksi.
A circular aluminum tube subjected to pure torsion by torques T(sec figure) has an outer radius r2equal to 1.5 times the inner radius r1. (a) If the maximum shear strain in the tube is measured as 400 × 10-6 rad, what is the shear strain y1at the inner surface? (b) If the maximum a1lo-abk rate of twist is 0.125 °/m and the maximum shear strain is to be kept at 400 × 10-6 rad by adjusting the torque T, that is the minimum required outer radius ( r2)Min?
A solid copper bar of circular cross section has length L = 1.25 m and shear modulus of elasticity G = 45 GPa. The bar is designed to carry a 250 N · m torque acting at the ends. If the allowable shear stress is 30 M Pa and the allowable angle of twist between the ends is 2.5°, what is the minimum required diameter?
Solve the preceding problem for the following data: diameter LO m, thickness 48 mm, pressure 22 MPa, modulus 210 GPa. and Poisson's ratio 0.29
A hollow steel shaft used in a construction auger has an outer diameter d2= 6.0 in. and inner diameter d1= 4.5 in. (see figure). The steel has a shear modulus of elasticity G = 11.0 × 106 psi. For an applied torque of 150 kip-in., determine the following quantities: shear stress at the outer surface of the shaft, shear stress at the inner surface, and rate of twist (degrees per unit of length). Also, draw a diagram showing how the shear stresses vary in magnitude along a radial line in the cross section.
A solid brass bar of diameter d = 1.25 in. is subjected to torques T1as shown in part a of the figure. The allowable shear stress in the brass is 12 ksi. What is the maximum permissible value of the torques T1? If a hole of diameter 0.625 in. is drilled longitudinally through the bar, as shown in part b of the figure, what is the maximum permissible value of the torques T2? What is the percent decrease in torque and the percent decrease in weight due to the hole?