A horizontal pipe of 100-mm-diamter and 1 m long with a surface temperature of 94 ℃ is used to condense saturated steam at 1 atm. Determine the heat transfer rate for the condensation process. Properties of Water, vapor (1 atm): Tsat = 100℃, ρv = 0.596 kg/m3, hfg = 2257 kJ/kg;Water, liquid (Tf = 370K): ρl = 960.6 kg/m3, Cpl = 4214 J/kg.K, μl = 289*10^-6 N.s/m2, kl = 0.679 W/m.K. Select one:

A horizontal pipe of 100-mm-diamter and 1 m long with a surface temperature of 94 ℃ is used to condense saturated steam at 1 atm. Determine the heat transfer rate for the condensation process. Properties of Water, vapor (1 atm): Tsat = 100℃, ρv = 0.596 kg/m3, hfg = 2257 kJ/kg;Water, liquid (Tf = 370K): ρl = 960.6 kg/m3, Cpl = 4214 J/kg.K, μl = 289*10^-6 N.s/m2, kl = 0.679 W/m.K. Select one:

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter9: Heat Transfer With Phase Change

Section: Chapter Questions

Problem 9.23P

See similar textbooks

Similar questions

What is condensation and when does occurs? How does filmwise condensation differs from drop-wise condensation? Which type has a higher heat transfer film coefficient and point out the reason thereof?
Saturated, pure steam at a temperature of 170 oC condenses on the outer surface of a vertical tube of outer diameter 2 cm and length 1.5 m. The tube surface is maintained at a uniform temperature of 150 oC. Calculate: the local film condensation heat-transfer coefficient at the bottom of the tube. the average condensation heat-transfer coefficient over the entire length of the tube. the total condensation rate at the tube surface.
a) the local film condensation heat-transfer coefficient at the bottom of the tube b) the average condensation heat-transfer coefficient over the entire length of the tube c) the total condensation rate at the tube surface.
Saturated, pure steam at a temperature of 170 oC condenses on the outer surface of avertical tube of outer diameter 2 cm and length 1.5 m. The tube surface is maintained at auniform temperature of 150 oC.Calculate:a) the local film condensation heat-transfer coefficient at the bottom of the tube. b) the average condensation heat-transfer coefficient over the entire length of the tube. c) the total condensation rate at the tube surface.
Will the largest condensation heat transfer coefficient always be obtained for a horizontal finned tube with the maximum possible fpm?
b) the average condensation heat-transfer coefficient over the entire length of the tube.c) the total condensation rate at the tube surface.
a film-type condenser consists of a packed bed of 3-cm diameter spheres with a voidage of 35%. water sprayed onto the bed at 60oC is used to condense steam entering at the base at a saturation temperature of 100oC. How deep must the bed be to ensure complete condensation of the steam, and what is the outlet temperature of the water? (Use water properties based on the mean of the inlet and outlet water temperatures, and iterate if necessary)
Saturated steam at 1 atm condenses on a 3-m-high and 5-m-wide vertical plate that is maintained at 90 0C by circulating cooling water through the other side. Determined (a) the rate of heat transfer by condensation to the plate, and (b) the rate at which the condensate drips off the plate at the bottom (Please use the condensation formulations at the Geankoplis).
Which of the following is not an assumption that Nusselt made in analytically deriving the average heat transfer coefficient over a vertical surface surrounded by vapor undergoing film condensation? A. Film thickness is zero at the top of surface B. Falling film is undergoing laminar flow C. Heat transfer from the condensing vapor to the surface is happening via natural convection D. All the assumptions above are important to the film condensation problem
What do you mean by condensation? Explain in details.
. A bomb calorimeter is used to determine the Higher Caloric Value of an oil sample . the mass of the sample is 2.12g. The total equivalent mass of water is 1.84kg. The increase in temperature after ignition is 8.9K . 2.9g of condensate is formed after it has cooled. Calculate the higher and lower calorific values. The specific heat of water is 4.186kJ/kgk.