A vertical plate 350mm high and 240mmwide, at 40°C, is exposed to saturated steam at 1 atm. Calculate the: 1- Film thickness at the bottom of the plate. 2- Maximum velocity at the bottom of the plate. 3- Total heat flux to the plate. 103) The properties of steam and the condensate [hfg = 2257 x , kg µ = 406 x 10-6 kg/m.s,p = 977.8 kg/m³,kf = 0.668 W /m. k].

A vertical plate 350mm high and 240mmwide, at 40°C, is exposed to saturated steam at 1 atm. Calculate the: 1- Film thickness at the bottom of the plate. 2- Maximum velocity at the bottom of the plate. 3- Total heat flux to the plate. 103) The properties of steam and the condensate [hfg = 2257 x , kg µ = 406 x 10-6 kg/m.s,p = 977.8 kg/m³,kf = 0.668 W /m. k].

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter8: Natural Convection

Section: Chapter Questions

Problem 8.28P

See similar textbooks

Similar questions

what two fundamental parameters of superfluid tell you if the superfluid is type one or type two?
The hot water coming out of a hydrothermal vent is sometimes called vent fluid. Why would you and I find these vent fluids to be an unpleasant thing to be exposed to? a They are some of the coldest fluids on Earth, being much colder than the normal freezing point of water. b They can be up to 400 degrees Celsius, and contain dissolved compounds like hydrogen sulfide, carbon dioxide, and methane. c The vent fluids are actually an exotic type of magma, made of silicate minerals. d They are actually ultra-pure water, with nothing at all dissolved in them; so pure that even simple cells will die due to the lack of nutrients in the fluids.
Henry's constant for air at 25 C is ____orders of magnitude higher than hydrogen sulfide
A gasoline engine is at a location where the temperature is measured to be 14.2 °C and produces 347 KW at 5800 rpm while consuming 0.0184 kg's of fuel. During operation, data shows that its mechanical energy loss is 18 %, the actual volume of air going into each cylinder is 80% (the volumetric efficiency has a negligible variation), and the actual fuel-to-air ratio is 0.065. What were the engine parameters at sea level conditions if the pressure here is 100.3 kPa and the temeratur here is 18 Uc hotter than that of the alevated conditions? Determine at sea-level conditions the ISFC in ka/kW-hr Use four (4) decimal places in your solution and answer.
A gasoline engine is at a location where the temperature is measured to be 14.2 °C and produces 347 KW at 5800 rpm while consuming 0.0184 kg's of fuel. During operation, data shows that its mechanical energy loss is 18 %, the actual volume of air going into each cylinder is 80% (the volumetric efficiency has a negligible variation), and the actual fuel-to-air ratio is 0.065. What were the engine parameters at sea level conditions if the pressure here is 100.3 kPa and the temeratur here is 18 Uc hotter than that of the alevated conditions? Determine at sea-level conditions the ISFC in ka/kW-hr
When water boils in a pot with a loose lid, the increased pressure forces the lid upward, releasing steam and reducing the pres- sure in the pot so that the lid drops back down. If the water continues to boil, the lid can rattle upward and downward. Consider a 1 L pot half filled with boiling water. In this case there is half a liter, or 1 mol, of air and steam above the water. (a) Estimate the mass of the lid. (b) When the water is rapidly boiling, estimate the height to which the lid jumps during a steam-release event. (c) By multiplying the weight of the lid by the height of the jump, estimate the work done by the steam as the lid moves upward. (d) Treat the process as adiabatic and use the first law of thermodynamics to estimate the drop in the temperature of the steam as it pushes the lid upward.
A 2 m wide, 3 m high, and 50 mm thick sheet of XPS insulation (M = 50 ng/Pa.s.m2), has a vapor pressure of 1500 Pa on one side, and 3500 Pa on the other. Calculate the vapor flow rate (Qv), vapor flux (qv), permeability, Rv value and the permeability (μ)
SUPPOSE THE AMBIENT TEMPERATURE IS 20degrees CELSIUS, AND THE HOT RESERVOIR CONSISTS OF A SPHERICAL TANK WITH A RADIUS OF 4.00 m, THAT ACTS AS AN IDEAL EMITTER OF RADIATION. IF ALL THE RADIANT ENERGY EMITTED BY THE TANK COULD BE CAPTURED, WHAT IS THE AVERAGE AMOUNT OF WORK THAT COULD BE DONE EACH SECOND? ( please only answer if your 100% correct) (show work)
Water is to be boiled at atmospheric pressure in a polished copper pan by means of an electric heater. The diameter of the pan is 0.48 m and is kept at 108 deg C. What is the power required to boil the water? Tsat 100°C; Properties of water at 100°C: Density. pl= 961 kg/m3; Kinematic viscosity, v 0.293x10-6 m2/s: Prandti Number. Pr 1.740; Specific heat, Cpl = 4216 J/kg.K; Dynamic viscosity, u = p x v = 961 x 0.293 x 10-6 = 281.57 x10-6 Ns/m2; hfg = 2256.9 k/kg; pv = 0.597 kg/m3; a = 0.0588 N/m; Csf=0.013; n=1:
A saturated steam at 410K is being transported in a pipeline (brass drawing tubing) at a rate of 1 grams/second. Pipe has inside diameter of 0.025 m . The tube is 100m long. The pressure at the entrance is 80kPa. It will under compressible or incompressible criteria. (use Perry's Handbook for the properties and constants) R = 8314J/kgmol.K; MW=18.02g/mol
Water is to be boiled at atmospheric pressure in a polished copper pan by means of an electric heater. The diameter of the pan is 0.51 m and is kept at 111 deg C. What is the power required to boil the water? Tsat = 100°C; Properties of water at 100°C: Density, ρl= 961 kg/m3; Kinematic viscosity, ν = 0.293x10-6 m2/s; Prandtl Number, Pr = 1.740; Specific heat, Cpl = 4216 J/kg.K; Dynamic viscosity, μ = ρ × ν = 961 × 0.293 × 10-6 = 281.57 x10-6 Ns/m2; hfg = 2256.9 kJ/kg; ρv = 0.597 kg/m3; σ = 0.0588 N/m; Csf=0.013; n=1; Select one: a. 25964.0356 b. 52997.1101 c. 49373.4011 d. 38911.7986
Engine oil enters the 5 mm diameter pipe at 120°C. The pipe surface temperature is kept at 40°C and the Re number is about 1000. Calculate the heat lost by the fluid for a 30 cm long pipe? Engine oilYou can get its specs at 390K.