A Horizontal tube has a diameter of 7 in., in which alcohol (spec. grav. = 0.80) is flowing at the rate of 4.38 slugs/s. The pressure is 2,200 lbs/ft^2. If the tube gradually decreases to 4.5 in. in diameter, what is the pressure there

Q: draws 1.42 m^3 p pressure of 2.54 300 mm diamet

A: given:

Q: A 5 cm diameter of water jet strikes a flat plate which held normal to the direction of the water je...

A:

Q: Write notes with sketch on (i) Gear pump (ii) Peristaltic pump.

A: Gear pump:  A gear pump uses the meshing of gears to pump fluid by displacement. They are one of t...

Q: the Mohr's circle

A: Given; The stress at a point in a material under plane stress conditionis uqui-biaxial tension with ...

Q: servoir of glycerin has a mass of 1,200 kg and a volume of 0.952 cu.m. Find its (a) weight (b) unit ...

A: Given:m=1200 kgV=0.952 m3

Q: Each time a double-acting hydraulic cylinder extends and retracts through an 8-in. stroke cycle, a l...

A: Volume of the drop of oil ,V=π/4(Do^2-Di^2)*L where Di=Do-2*film thickness (t) L=stroke length =π/4(...

Q: Carbon is allowed to diffuse through a steel plate 10mm thick. The concentrations of carbon at the t...

A: Ghghgh

Q: Q17. As shown in the image below, the 0.5-kg ball strikes the rough ground and rebounds. The directi...

A:

Q: Q22. As shown in the image below, the force acting on the 5-kg crate is a function of time. The coef...

A:

Q: otnent of imer tia moment

A: Given; A flywheel is attached to an engine to keep its rotationalSpeed between maximum to minimum;  ...

Q: What modulus of elasticity in tension is required to obtain a unit deformation of 0.00105 m/m froma ...

A:

Q: The steel plate shown in the figure is connected to a gusset plate by M20 bolts. Check if the plate ...

A: given; →number of bolts(n)=8→diameter of bolts(d)=20mm→axial load(P)=500KN                   =500*10...

Q: 4m 10m F 6 m, 8 m Zom- 8m

A: Find the moment about origin (O) Given data :-  F = 300 N

Q: .She was half . hour late The O A An O No thing O هذا السؤال مطلوب Nadia always hard before ...........

A: Correct answer: an Reason: We know that, the preposition 'an' comes before a, e, i, o, u words. At s...

Q: under the impact. The diameter. of spring wire is 25 mn and mean diameter of coil is 200 mm. Find ma...

A:

Q: A cantilever type gate hinged at Q is shown in the figure P and R are the centres of gravity of the ...

A: Given: A cantilever type gate,mass of the cantilever part , P=75 kg

Q: Find the velocity of flow of an oil through a pipe, when the difference of mercury level of differen...

A:

Q: During a race the dirt bike was observed to leap up off the small hill at A at an angle of 60° with ...

A: Speed is the distance covered per unit of time which means the rate change of the distance is known ...

Q: 14. A Carnot refrigerator requires 10 kW to remove 20 klis from a 20°C reservoir. The temperature of...

A: As per given  Temperature =20° c We have to determine temperature of reservoir

Q: What are the benefits of learning and studying occupational safety and health and consider this to b...

A: Great OSH is really great for business Further developed usefulness through less disorder nonattend...

Q: teel wire 5u-m long hanging vertically supports a weight of 1200 N. Determine the required wire diam...

A: Given;-δ=PLAE4x10-3=1200x5π4xd2x200x1094x10-3=1200x5x4πxd2x200x109d2=1200x5x4πxd2x200x109x4x10-3d=3....

Q: Study the table to the right and then answer these questions by filling in the blank columns in the ...

A:  use given formula to convert to chane miles per milesgallon1 kilometer0.621 miles0.265 gallon1 litr...

Q: a certain point in a stressed body, the principal stresses are fx=80 MPa and fy=-40MPa. Determine th...

A: Given:σx=80 MPaσy=-40 MPaθ=30°

Q: Shaft.pdf

A: Shaft = 40C8 SteelRotates N=1500rpmkb=1.5kt=1.2 To-Find:- Diameter of the shaft

Q: 2. A l-in diameter rotating solid round bar has a groove 0.1-in deep with a 0.1-radius machined into...

A: Given data as per question Bending moment =1000 lbf. in f =0.9  q = 0.8 Calculations tensile strengt...

Q: Thermal efficiency of a power cycle is 0.8. For the cycle, Qout = 250 kJ. Determine Qin in kJ.

A: Answer: Oin = 1250 kJ.  

Q: Q3: Consider evaluation of different temperatures of solar photovoltaic/thermal system (PVT) as show...

A:

Q: The bell crank, which is in equilibrium under the forces shown in the figure, is supported by a 25-m...

A: To calculate the reaction forces in the pin joint, the three equations of statics can be used which ...

Q: A tractor operating at 3.5 mph develops 3000 pounds drawbar pull in pulling a trailer. Estimate the ...

A: Answer: The required drawbar horsepower of the tractor is 28 hp.  

Q: DETERMINE THE DEFLECTION AT POINTSB AND C. El=50.0x103 kN-m2 24 kN/m B EI 3.0 m 3.0 m 1.5 m 7.5 m

A:

Q: Block B moves down with a constant velocity of 12 mm/s. Block A starts from rest at t = 0 and moves ...

A: Given: Constant velocity of B→VB=12 mmsec block A starts from rest at t=0 sec so initial velocity of...

Q: A one-stage compressor with an ideal intercooler receives 0.5m3/s of Helium at 150kpa and 300K and d...

A: Given data: V˙=0.5 m3/sP1=150 kPaP2=8600 kPaT1=300 K Need to determine the heat rejected at the inte...

Q: DETERMINE THE TURBINE WORK AND ENGINE EFFICIENCY IF THE INLET PRESSURE AND TEMPERATURE ARE 23MPA AND...

A:

Q: Determine the yield strength of a material required such that the component would not fail when subj...

A:

Q: For the mechanical translation system below, find the transter function X2/F and X1/F. Use the follo...

A:

Q: Classify the following as rigid or movable system boundary: a. your mouth when you exhale b.  A cu...

A:

Q: A long plastic rod of 20-mm diameter (k = 0.3 W/m-K and pc, = 1040 kJ/m3.K) is uniformly heated in a...

A: Given: The diameter of rod, d = 20 mm = 0.02 m The thermal conductivity, k = 0.3 W/m.K The multiplic...

Q: What is the mass flow rate of airflow, with a Mach number of 0.230, Area of 10 in^2, Speed of sound ...

A: Given data Mach number = 0.230 Area  = 10 sq. in =0.0064516m²  Speed of sound = a = 200 ft/s = 60.96...

Q: The motion of a particle is defined by the relation x = t^3 - 9t^2 + 24t - 8, where x and t are expr...

A: The displacement traveled per unit time is known as the velocity, it is the vector quantity that mea...

Q: Tengins Given that p <q<r<s. Which of the

A: Given: p&lt;q&lt;r&lt;s

Q: . Determine the velocity and displacement of the body

A: Determine the velocity and displacement of the body

Q: following observations obtained in the boys gas calorimeter equipment find the gcv and ncv of the fu...

A:   Given; V=0.08 m3∆t=9.1°Cw=29.5 kg

Q: 1.C.5. The refrigerant in an evaporator goes through phase change at a constant temperature of −30◦C...

A:

Q: Why does a turbine blade which breaks during the operation of an aeroengine need to be contained wit...

A: During the operation of aerodynamics there is very high speed in very very high altitude. If the bro...

Q: he maximum thermal efficiency possible for a power cycle operating between 1200°F and 225°F is: The ...

A: Given:T1=1200°FT2=225°F

Q: A mechanism is shown in Figure 2, the pendulum O, A rotates anti-clockwise about point 0, with a con...

A:

Q: In a certain diesel- electric power plant, diesel generator set has the following data: Diesel fuel...

A: “Since you have posted a question with multiple sub-parts, we will solve first three sub-parts for y...

Q: D1 H D2

A: GIVEN DATA- D1=40in D2=20in H=6ft Q=1ft3/s WE HAVE TO FIND PRESSURE DIFFERENCE

Q: n end force of 15 kN inc rot or go

A:

Q: A strip of thickness 40 mm is to be rolled to a thickness 20 mm using a two-high mill having a rolls...

A: Given data: hi=40 mmhf=20 mmD=200 mm Need to determine the coefficient of friction and arc length.