A hot air balloon is tethered to the ground with three cables as shown in the figure. If the balloon is pulling upwards with a force, F of 720 kN, what is the magnitude of the tension in KN in cable OB? Provide your answer with 2 decimal places with no units. A4.2 m Z 5.6 m F 3.3 m C 2.4 m B 4.2 m X

A hot air balloon is tethered to the ground with three cables as shown in the figure. If the balloon is pulling upwards with a force, F of 720 kN, what is the magnitude of the tension in KN in cable OB? Provide your answer with 2 decimal places with no units. A4.2 m Z 5.6 m F 3.3 m C 2.4 m B 4.2 m X

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter10: Force And Force-related Variables In Engineering

Section: Chapter Questions

Problem 29P: A structural member with a rectangular cross section as shown in the accompanying figure is used to...

See similar textbooks

Similar questions

Answer is 1,022.80. Show your solution. Forces F1 and F2 shown below act on the screw eye. If F1 = 501 lb, determine the magnitude of the resultant force (in lb) if it is directed vertically upward. Use F2 = 578 lb., α = 20°.
Consider the frame shown in (Figure 1). Suppose that F1 = 3.5 kN. a) Determine the x and y components of the force that the pin at B exerts on the frame using scalar notation. b) Determine the x and y components of the force that the pin at A exerts on the frame using scalar notation. Express your answers in kilonewtons to three significant figures. Enter your answers separated by a comma.
F1 = 4 kNF2 = 3 kNF3 = 2 kNa = 3 mb = 5 mc = 4 mtheta = 33 degrees Find the magnitude of the resultant couple moment (in kN-m).If the calculated answer is not whole number, express it in 4 significant figures. If the value is negative, include a negative sign.
Need help experts. The rigid body shown in the figure is subjected to the indicated force system. Determine the forces applied at points A and E that equal the applied force system.Data: β = 48°; a = 6,6 m; b = 8,9 m; F = 31 kN; P1 = 20,743 kN; P2 = 23,037 kN The force applied at point A is FA = ? Answer kN and the force applied at point B is FB = ? Answer kN.
The forces are acting at the same point as shown in Figure Q1. Determine the magnitude and direction of the resultant force of these forces. You may assume θ = 50º. If an additional force needs to be applied to the same point so that the whole forces remain equilibrium, what is the magnitude and direction of an additional force acting at that point? Figure Q1, (refer picture below for better understanding)
The figure shows a pellet about to be fired from a sling. The total unstretched length of the rubber band is 80mm. The rubber band elongates 1mm for every 15N force.Given: a=100mm b=40mm 1. As the pellet is about to be released, how much is the elongation on each leg (mm) of the rubber band? 2. What is the force (N) exerted on each leg of the rubber band? 3. What is the pulling force (N)?
The cross section of the rim of an iron flywheel (S+3) ft. In diameter is a triangle 12" by 3". How much does the rim weigh? Note: Iron weighs 450lb/cu ft. S=10
Alice is to walk across a “high wire” strung horizontally between twobuildings 10.0 m apart. The rope make a sag of 10.0° at horizontal whenshe is at the midpoint. If her mass is 50.0 kg, what is the tension in the ropeat this point? INCLUDE THE GIVEN AND MAKE A FIGURE
Problem 9. For the tank shown in the figure, the following dimensions apply: h1=3.00m h2=4.50m w=2.50m y=9.81kN/m^3. Compute the horizontal component of the resultant force on the curved surfaces.a. 168.0 kNb. 158.0 kNc. 148.0 kNd. 138.0 kNe. 128.0 kNf. 118.0 kN
From the given figure, shown determine the moment at point A. The unit for Force is in pounds(lbs) and Length is in inches(in). F=3,728 N=1,893 M=7,865 P=4,294
Calculate the internal torques T1, T2, T3, and T4 in shaft segments (1), (2), (3), and (4), respectively. Answers in lb-ft
A grindstone in the shape of a solid disk with diameter 0.520 m and a mass of 50.0 kg is rotating at 850 rev/min. You press an axe against the rim with a normal force of 160 N (see Figure below), and the grindstone comes to rest in 7.50 s. 1) What is the moment of inertia of the grindstone? 2) What force is bringing the grindstone to a stop? What is the net torque caused by that force? 3) What is the size of the force? 4) What is the coefficient of friction between the axe and the grindstone?