The figure shows a pellet about to be fired from a sling. The total unstretched length of the rubber band is 80mm. The rubber band elongates 1mm for every 15N force.Given: a=100mm b=40mm 1. As the pellet is about to be released, how much is the elongation on each leg (mm) of the rubber band? 2. What is the force (N) exerted on each leg of the rubber band? 3. What is the pulling force (N)?

The figure shows a pellet about to be fired from a sling. The total unstretched length of the rubber band is 80mm. The rubber band elongates 1mm for every 15N force.Given: a=100mm b=40mm 1. As the pellet is about to be released, how much is the elongation on each leg (mm) of the rubber band? 2. What is the force (N) exerted on each leg of the rubber band? 3. What is the pulling force (N)?

Engineering Fundamentals: An Introduction to Engineering (MindTap Course List)

5th Edition

ISBN:9781305084766

Author:Saeed Moaveni

Publisher:Saeed Moaveni

Chapter15: Computational Engineering Tools Matlab

Section: Chapter Questions

Problem 14P

See similar textbooks

Similar questions

A structural member with a rectangular cross section as shown in the accompanying figure is used to support a load of 2500 N. What type of material do you recommend be used to carry the load safely? Base your calculations on the yield strength and a factor of safety of 2.0.
In the figure below, the weight of the block is 300 kg and the angle of internal friction is 24.2 degrees. a. If h = 50 cm and P = 50 kg. does the block move? b. If h = 50 cm, what is the smallest P to start motion?
1. Given: X = 100 kg; Y = 150 kg Solve for the acceleration of block X in m/s2 for Case 1. Ignore the friction and mass of pulleys. (3 significant figures)
A grindstone in the shape of a solid disk with diameter 0.520 m and a mass of 50.0 kg is rotating at 850 rev/min. You press an axe against the rim with a normal force of 160 N (see Figure below), and the grindstone comes to rest in 7.50 s. 1) What is the moment of inertia of the grindstone? 2) What force is bringing the grindstone to a stop? What is the net torque caused by that force? 3) What is the size of the force? 4) What is the coefficient of friction between the axe and the grindstone?
In the given figure below, a tube was supported at A and E with a ball and socket and a wire at D connected to F. Determine the following give that Force F is equal to 690.86 N. Note: Express your answer in terms of the units. Observe 3 decimal places. The error threshold is ± 2.50% Relative to the right answer. XB: 188.419mm Xc: 471.768mm Ya: 209.808mm Ze: 155.444 mm Zf: 471.096 mm 5.) Determine the x-component of the moment experienced by the system assuming that there is no wire support. 6.) Determine the y-component of the moment experienced by the system assuming that there is no wire support. 7.) Determine the z-component of the moment experienced by the system assuming that there is no wire support. 8.) Determine the Tension experienced by the wire DF.
The figure shown is formed of 1/8 -in.-diameter steel wire. Knowing that the specific weight of the steel is 490 lb/ft3 , determine the mass moment of inertia of the wire with respect to each of the coordinate axes.
6.) The figure shows a metal hanging by a thin wire from a floating wood block. The wood block has a specific gravity Sb =0.25, a square base of 80 mm x 80 mm and height of 15 mm. The metal has a volume of 8000 mm^3. Using a unit weight of water 9800 kN/m^3 and g=9.80 m/s^2, find the tension in the thin wire in Newton. Write your answer in three decimal places. fluid mechanics
In the figure shown, an open tank when empty the water surface is at point A and the gauge fluid mercury shows a deflection of 20mm. Determine the new deflection of mercury when the tank is filled with water to B.
In the given figure below, a tube was supported at A and E with a ball and socket and a wire at D connected to F. Determine the following give that Force F is equal to 690.86 N. Note: Express your answer in terms of the units. Observe 3 decimal places. The error threshold is ± 2.50% Relative to the right answer. XB: 188.419mm Xc: 471.768mm Ya: 209.808mm Ze: 155.444 mm Zf: 471.096 mm 1.) Determine x-component of vector DF. 2.) Determine the y-component of Vector DF 3.) Determine the z-component of Vector DF. 4.) Determine the moment experienced by the system assuming that there is no wire support.
Figure shows a slender uniform rod with mass M and length L. It might be a baton held by a twirler in a marching band (without the rubber end caps). (a) Use integration to compute its moment of inertia about an axis through O, at an arbitrary distance h from one end. (b) Initially the rod is at rest. It is given a constant angular acceleration of magnitude a around the axis through O. Find how much work is done on the rod in a time t. (c) At time t, what is the linear acceleration of the point on the rod farthest from the axis?
In the figure, a motor weighing 3000 N hangs from a chain attached by an O-ring to two other chains, one attached to the ceiling and the other to the wall. Calculate the tension force T2 acting on the chain attached to the wall. Consider that the weights of the chains and the ring are negligible. solve and choose the correct alternative A) 3464 N B) 1732 N C) 346.4 N D) 173.2 N
A string is wrapped around the hub of the spool. a pull at the end of the string causes the spool to roll on the horizontal plane without slipping. At a certain instant, the angular velocity and angular acceleration of the spool are as shown in the figure. For this instant, find (a) the acceleration of the point D on the spool; (b) the acceleration of point B ; and (c) the acceleration a0 of the end of the string.