= A hot surface at 100°C is to be cooled by attach- ing 3-cm-long, 0.25-cm-diameter aluminum pin fins (k 237 W/m. °C) to it, with a center-to-center distance of 0.6 cm. The temperature of the surrounding medium is 30°C, and the heat transfer coefficient on the surfaces is 35 W/m² °C. Determine the rate of heat transfer from the surface for a 1-m x 1-m section of the plate. Also determine the overall effectiveness of the fins. . -3 cm. 0.6 cm 가 0.25 cm

= A hot surface at 100°C is to be cooled by attach- ing 3-cm-long, 0.25-cm-diameter aluminum pin fins (k 237 W/m. °C) to it, with a center-to-center distance of 0.6 cm. The temperature of the surrounding medium is 30°C, and the heat transfer coefficient on the surfaces is 35 W/m² °C. Determine the rate of heat transfer from the surface for a 1-m x 1-m section of the plate. Also determine the overall effectiveness of the fins. . -3 cm. 0.6 cm 가 0.25 cm

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter2: Steady Heat Conduction

Section: Chapter Questions

Problem 2.60P

See similar textbooks

Similar questions

2.38 The addition of aluminum fins has been suggested to increase the rate of heat dissipation from one side of an electronic device 1 m wide and 1 m tall. The fins are to be rectangular in cross section, 2.5 cm long and 0.25 cm thick, as shown in the figure. There are to be 100 fins per meter. The convection heat transfer coefficient, both for the wall and the fins, is estimated to be K. With this information determine the percent increase in the rate of heat transfer of the finned wall compared to the bare wall.
A person puts a few apples into the freezer at 15°C cool them quickly for guestswho are about to arrive. Initially, the apples are at a uniform temperature of 20°C,and the heat transfer coefficient on the surfaces is 8 W/m2·K. Treating the apples as9-cm-diameter spheres and taking their properties to be 840 kg/m3, Cp 3.81 kJ/kg·K, k = 0.418 W/m·K, and α =10-7 m2/s, determine the center and surface temperatures of the apples in 1 h. Also, determine the amount of heat transfer from each apple. Solve this problem using analytical one-term approximation method (notthe Heisler charts). Answer: Center: 11.2 ℃, Surface: 2.7 ℃, heat transfer: 17.2 kJ
A cylindrical fuel rod of 2 cm in diameter is encased in a concentric tube and cooled by water. The fuel generates heat uniformly at a rate of 150 MW/m3. The convection heat transfer coefficient on the fuel rod is 5000 W/m2∙K, and the average temperature of the cooling water, sufficiently far from the fuel rod, is 70°C. Determine the surface temperature of the fuel rod and discuss whether the value of the given convection heat transfer coefficient on the fuel rod is reasonable.
Consider a 2-m-high electric hot-water heater thathas a diameter of 40 cm and maintains the hot water at 55°C.The tank is located in a small room whose average temperatureis 27°C, and the heat transfer coefficients on the innerand outer surfaces of the heater are 50 and 12 W/m2·K,respectively. The tank is placed in another 46-cm-diametersheet metal tank of negligible thickness, and the spacebetween the two tanks is filled with foam insulation (k =0.03 W/m·K). The thermal resistances of the water tank andthe outer thin sheet metal shell are very small and can be neglected. The price of electricity is $0.08/kWh, and the home owner pays $280 a year for water heating. Determine the fraction of the hot-water energy cost of this household that is due to the heat loss from the tank. Hot-water tank insulation kits consisting of 3-cm-thick fiberglass insulation (k = 0.035 W/m·K) large enough to wrap the entire tank are available in the market for about $30. If such an insulation is installed on…
Consider a person standing in a breezy room at 20°C. Determine the total rate of heat transfer from this person if the exposed surface area and the average outer surface temperature of the person are 1.6 m2 and 29°C, respectively, and the convection heat transfer coefficient is 6 W/m2 ·°C (Fig. 2–75).
Consider a cold aluminum canned drink that is initially at a uniform temperature of 4°C. The can is 12.5 cm high and has a diameter of 6 cm. If the combined convection/radiation heat transfer coefficient between the can and the surrounding air at 25°C is 10 W/m2 · °C, determine how long it will take for the average temperature of the drink to rise to 15°C. In an effort to slow down the warming of the cold drink, a person puts the can in a perfectly fitting 1-cm-thick cylindrical rubber insulator (k = 0.13 W/m · °C). Now how long will it take for the average temperature of the drink to rise to 15°C? Assume the top of the can is not covered.
A 0.3-cm-thick, 12-cm-high, and 18-cm-long circuit board houses 80 closely spaced logic chips on one side,each dissipating 0.06 W. The board is impregnated with copper fillings and has an effective thermalconductivity of 16 W/m · °C. All the heat generated in the chips is conducted across the circuit board andis dissipated from the back side of the board to the ambient air at 30°C, which is forced to flow over thesurface by a fan at a free-stream velocity of 400 m/min. Determine the temperatures on the two sides ofthe circuit board.
A 0.3-cm-thick, 12-cm-high, and 18-cm-long circuit board houses 80 closely spaced logic chips on one side, each dissipating 0.06 W. The board is impregnated with copper fillings and has an effective thermal conductivity of 16 W/m · °C. All the heat generated in the chips is conducted across the circuit board and is dissipated from the back side of the board to the ambient air at 30°C, which is forced to flow over the surface by a fan at a free-stream velocity of 400 m/min. Determine the temperatures on the two sides of the circuit board.
A 5 m long section of a steam pipe whose outer diameter is 10 cm passes through an open space at 30°C. The average temperature of the outer surface of the pipe is measured to be 150°C, and the average heat transfer coefficient on that surface is determined to be 180 W/m^2.k. Determine (a) the rate of heat loss through convection from the steam pipe and (b) the annual cost of this energy loss if steam is generated in a natural gas furnace, and the price of natural gas is 0.05 Rs/Kwh, consider a 250 working-day year.
Consider a steam pipe of length 15 ft, inner radius 2 in., outer radius 2.4 in., and thermal conductivity 7.2 Btu/hr-ft-°F. Steam is flowing through the pipe at an average temperature of 250°F, and the average convection heat transfer coefficient on the inner surface is given to be 1.25 Btu/hr-ft2-°F. If the average temperature on the outer surfaces of the pipe is 160°F, determine the rate of heat loss from the steam through the pipe. ANSWER:______Btu/hr
A 40-cm-long, 800-W electric resistance heating element with diameter 0.5 cm and surface temperature 120°C is immersed in 75 kg of water initially at 20°C. Determine how long it will take for this heater to raise the water temperature to 80°C. Also, determine the convection heat transfer coefficients at the beginning and at the end of the heating process.
Consider hotdog being cooked in boiling water in a pan. Would the heat transfer be modeled as one-dimensional or two-dimensional? Would the heat transfer be steady or transient? Explain.