What is the shortcut key for "Find and ?Replace" dialog box + Ctrl + Shift + FO Ctrl + RO Ctrl + FO Ctrl + HO

Q: What is the meaning of the abbreviation ?WCS in AutoCAD 3D World coordinate system O We coordinate…

A: WCS : World Coordinate System

Q: A mechanical system is shown in the figure below. This system consists of a damper (b), spring (k)…

A: Given : To find : Change in response

Q: 9.92 kg of R-134a at 300 kPa fills a rigid container whose volume is 14 L Determine the temperature…

A:

Q: Determine the reactions of the beam using Force Method Analysis. Set A is fixed, B is roller and w =…

A:

Q: Problem 22. A simply supported beam of span L is carrying a concentrated load P at the centre and a…

A: A simply supported beam with a span L carries a concentrated load P in the centre and an evenly…

Q: The engineer needs to design a cylinder shaft, with length L=1 m, to transmit a power of 500W and…

A: Given data Length of shaft = l  = 1mPower transmitted = 500 WRotation speed = N = π rad/sRadius of…

Q: Draw the shear-force and bending-moment diagram for the beam shown. Assume the upward reaction…

A: Given: a=5 ft and b=3.4 ft Value of P=25 kips Value of w=1.1 kips/ft Hence total downward force:…

Q: Consider the wing channel in (Figure 1) with h=24 in. Neglect the effect of rounded corners. The…

A:

Q: an a thick saw blade be used as a broach. Why. Why is it difficult to make

A: As per the guidelines we are subjected to solve only one question at a time. Please repost the same…

Q: Draw a schematic flow diagram of a heat engine.

A: Draw a schematic flow diagram of a heat engine.

Q: In a stress-strain curve it is possible to characterize a material by analyzing it. Show a graph…

A: The deformation of a material in response to a tensile, compressive, or torsional force is…

Q: flywheel maximum speed is 240 rpm and decrease to 200 rpm during the punching stroke. The mean…

A:

Q: An electric motor weighs 1,800lbs & is provided with an eyebolt screwed in to the cast iron frame…

A: Given data   Electric motor weighs 1800 lbs Eyebolt is screwed for lifting purposes. We have to find…

Q: According to the figure (flywheel rotated about its center), the normal acceleration an of point A…

A:

Q: Compute the work done by the indicated force when the disk undergoes the specified displacement…

A:

Q: a) Ignoring the self-weight of the members, determine the support reactions.

A: we have to determine the reactions at A& D

Q: The torsional assembly consists of solid 1.6 in. diameter aluminum [G = 4,000 ksi] segments (1) and…

A:

Q: In figure, find the value of Qin, ?Qout, Q3 and Q4 (by m3/s) 0.3 m3/s 1 Q3 0.2 m3/s 0.1 m3/s Q4 3…

A:

Q: A card is selected from a deck. Find the probability that it is a number greater than or equal to 8…

A: Total number of cards in a deck, n= 52 There are two red suits( heart and diamond)  Each red suit…

Q: QUESTION 10 A Watt (W) is defined as one Joule (J) of energy per second (s): 1 W = 1 J/s. It is also…

A: The maximum range of the car is 326.1 miles.

Q: Use the graphical method to construct the shear-force and bending-moment diagrams for the beam…

A: According to Bartleby guidelines, we are allowed to solve only the first 3 sub-part of a single…

Q: (flywheel rotated about its center), The tangential acceleration at of point A is calculated to be…

A: Note:- As per our guidelines we are supposed to answer only one question. Kindly repost other…

Q: Q1 The slider of mass 1 kg attached to a spring of stiffness 400 N/m and unstretched length of 0.5 m…

A:

Q: What will be the potential energy of 1kg mass kept at height of 5 m. Take g = 10 m/s²

A: Given  : mass of body = m= 1 kg              height of body, h = 5 m               g= 10 m/s2 To…

Q: An aluminium hollow thin-wall torsion member shown in Fig. 3.15 is 3 m long. If a torque of 10 kN-m…

A:

Q: A wedge assembly, composed of wedges X and Y, is designed to lift crate W whose weight is 1936 N, as…

A: Given data Weight of block = 1936 NCoefficient of friction = µ = 0.0875We have to draw the free body…

Q: A helical compression spring is to be cycled between 150 lbf and 300 lbf with a 1-in stroke. The…

A: (Bartleby policy): Since you have posted a question with multiple sub-parts, we will solve the first…

Q: An oil having viscosity 0.08 N-s/m², specific weight 8829 N/m³, density 900 kg/m³ flows at the rate…

A:

Q: Problem 2: It is recommended to change the circular cross section shown in the figure by a square…

A: Diameter of the circular cross section, D= 4 in

Q: The figure shows a sensor indicating a gauge pressure reading of 1.5 kPa. The fluids are at 20°C…

A:

Q: Problem 3: Design a helical compression spring to be used to return a pneumatic cylinder to its…

A:

Q: The mass of gear A is 25 kg and its centroidal radius of gyration is 105 mm. The mass of gear B is…

A:

Q: determine the centroid of the plates given below

A:

Q: 4. Determine the accelerations of bodies A and B and the tension in the cable due to the application…

A: To determine the tension in the cable and acceleration of bodies A and B.

Q: Present an example of a material that has a yield stress and use the tangent crossing method to…

A: The material attribute described as the tension at which a material begins to distort plastically…

Q: Determine the vertical and horizontal deflec- tions of the end B due to load P of the thin curved…

A: The vertical and horizontal deflection of the end B of the thin curved bar of uniform cross section…

Q: Using the area method, draw the shear force and bending moment diagrams for the beam. Don't think…

A:

Q: A wedge assembly, composed of wedges X and Y, is designed to lift crate W whose weight is 1936 N, as…

A: Given data Weight of crate W = 1936 N Coefficient of friction on each surface = 0.0875  We have to…

Q: Using the area method, draw the shear force and bending moment diagrams for the beam. Don't think…

A:

Q: 5-62 Refrigerant-134a is throttled from the saturated liquid state at 700 kPa to a pressure of 160…

A: we have to evaluat final sp. volume

Q: 100kg of water at 75C and 1 bar is heated in a boiler to superheated steam at 5 bar and 350C.…

A: Use steam table to solve this problem

Q: Determine the thickness of a steel air receiver with 30 in. diameter and pressure load of 120 psi,…

A:

Q: Specify mechanical energy processes from non-traditional machining and which process is suitable for…

A: Unconventional machining is a method of machining that involves no direct contact between the tool…

Q: A gas refrigeration system using air as the working fluid has a pressure ratio of 4. Air enters the…

A: Given data as per question Pressure ratio, r = 4Temperature of air before compression,…

Q: Two long pipes in parallel are used to carry water between two reservoirs. The diameter of one pipe…

A:

Q: The materials having same elastic properties in alldirections are called

A:

Q: :) Select the lightest W-shape standard steel beam equivalent to the built-up steel beam below which…

A: we have to select the appropriate section for the given moment

Q: A triangular wooden body (S=0.80) is placed in water in the position indicated in the figure. If the…

A:

Q: A 3.6 m long shaft carries three pulleys, two at its two ends and third at the mid-point. The two…

A: L=3.6mmA=79kgmC=40kgCGA=3mm=0.003mCGC=5mm=0.005mmB=50kgCGB=8mm=0.008mN=300rpm=2×π×N60=2×π×30060=31.4…

Q: A pair of gray iron and steel helical gears, having a helix angle of 15° with 20° full-depth teeth…

A: Answer: (a) Normal circular pitch: 0.4335 in (b) Normal diametral pitch: 7.2470 in (c) Axial pitch:…