(a) If this motor is started from a 460-V infinite bus, how much current will flow in the motor at starting? line i with an impedance of 0.50 +0.35 per phase is used to connect the duction motor to the infinite bus, what will the starting current of the motor be? What will the motor's terminal voltage be on starting?

(a) If this motor is started from a 460-V infinite bus, how much current will flow in the motor at starting? line i with an impedance of 0.50 +0.35 per phase is used to connect the duction motor to the infinite bus, what will the starting current of the motor be? What will the motor's terminal voltage be on starting?

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter32: Three-phase Motors

Section: Chapter Questions

Problem 13RQ: A squirrel-cage induction motor is operating at 1175 RPM and producing a torque of 22 Ib-ft. What is...

See similar textbooks

Similar questions

A squirrel-cage induction motor is operating at 1175 RPM and producing a torque of 22 Ib-ft. What is the horsepower output of the motor?
An approximate per phase equivalent circuit of a 3-phase, 220-V, wye-connected, 6 pole, 60 Hz induction motor is shown in figure below for which R1 = 0.3 ohm; X1 = 0.4 ohm; R’2 = 0.4 ohm; X’2 = 0.6 ohm; Xm = 15 ohms. For the given numerical values calculate the total developed(electromagnetic) torque in (kg-cm) .The motor speed is 1080 rpm.
Q) A 3 phase ,delta connected 410v,50HZ,6 pole Induction motor has the following per phase parameters in ohms refered to the stator. R1 = 0.14Ώ,X1 = 0.44 Ώ ,R2 * = 0.12 Ώ,X2* = 0.43 Ώ,Xm = 28 Ώ.Calculate the stator current and power factor when the motor is operated at rated voltage and frequency with slip 0.03.?
The no-load and locked-rotor test results of a three-phase 10 HP, 220 V, 60 Hz, 6 poles star connected induction motor are; The no-load test: VNL=220 V, PNL=340 W, INL=6.2 A The locked-rotor test: VSC=54 V, PSC =430 W, ISC =15.2 A The voltage across the stator windings is 2 V when nominal DC current flows through it. Coefficient for DC resistance is 1,25. a) Calculate the equivalent circuit parameters and draw the complete single-phase equivalent circuit of the induction motor. b) Calculate efficiency of the motor for s=0.06 by using the approximate equivalent circuit (RFe core resistance is not ignored). c) Shaft torque for s=0,06 d) Slip value at the maximum (breakdown) torque, e) Maximum (breakdown) torque of the induction motor. f) Speed of the motor at maximum torque point. g) Rotor frequency at maximum torque.
PLEASE ONLY ANSWER THE D E F G PARTS PLEASE ANWSER AS SOON AS POSSIBLE. Thanks in advance. The no-load and locked-rotor test results of a three-phase 10 HP, 220 V, 60 Hz, 6 poles star connected induction motor are;The no-load test:VNL=220 V, PNL=340 W, INL=6.2 AThe locked-rotor test:VSC=54 V, PSC =430 W, ISC =15.2 AThe voltage across the stator windings is 2 V when nominal DC current flows through it. Coefficient for DC resistance is 1,25.a) Calculate the equivalent circuit parameters and draw the complete single-phase equivalent circuit of the induction motor.b) Calculate efficiency of the motor for s=0.06 by using the approximate equivalent circuit (RFe core resistance is not ignored).c) Shaft torque for s=0,06 d) Slip value at the maximum (breakdown) torque,e) Maximum (breakdown) torque of the induction motor.f) Speed of the motor at maximum torque point.g) Rotor frequency at maximum torque.
A 200V, 3, star connected induction motor takes 30A at a line voltage of 35V with rotor locked. With this line voltage, power input to motor is 450W and core loss is 60W.The dc resistance between a pair of stator terminals is 0.15Ω. If the ratio of ac to dc resistance is 1.6, find the equivalent leakage reactance/phase of the motor and the stator and rotor resistance per phase.
A 3-phase, star connected 440 V squirrel cage induction motor has the following equivalent circuit parameters in ohms per phase referred to stator: R1 =0.1=R2;X1 =0.4=X2;Xm =10.Determine: (a) the starting current of the motor, when switched direct on line, and (b) the stator current at the start of reverse current braking.
(b) A 415V, 50Hz, delta-connected, 4-pole, squirrel cage induction motor has a perphase equivalent circuit as shown in Figure Q4(b). The circuit parameter values (in Ω/phase) for the stator is as follows: R1 = 0.095 Ω ; R2 = 0.06 Ω; X1 = 0.68 Ω ; X2 = 0.67 Ω; Xm = 18 Ω The motor is running at 1400 rpm at full-load. The core loss of the motor is assumed to be zero. The total friction and windage losses is 600 W, independent of load. Determine the efficiency of the motor.
3-Phase 50Hz 6 pole induction motor has rotor resistance of 0.1 ohm and reactance of 0.92. ignore voltage drop in stator and assume thee rotor resistance is constant. Full load slip is 3%, then find the value of the maximum torque.
A 3Ø induction motor has a 4-pole, Y-connected stator winding. The motor runs on a50Hz supply with 200V between lines. The rotor resistance and reactance per phase are0.1 ohms and 0.9 ohms respectively. Calculate:a) The gross torque at 4% slip in N-mb) The maximum torque in ft-lbsThe ratio of rotor to stator turns is 0.67.
59 ۱۱:۶۳ ص | ۲۰۰۸ك.بث | A 460 V.pdf A 460 V, 60 Hz, Star connected, 870 r.p.m., Eight poles, Three-Phase Induction Motor has the following per phase parameters: R1 = 0.07, R2 = 0.05, X1 = X2 = 0.2, Xm = 6.5, Draw the approximate equivalent circuit and determine the following: 1. III. IV. V. VI. VII. Starting Torque Maximum Torque Rated Torque Stator Current Power Factor Input Power Magnetizing Current †
Please Do not Designed 15 Kw Please Must Show Given Questions in Design for 11KW Motor . A15 kW, 440 V, 4-pole, 50 Hz, 3-phase induction motor is built with a stator bore 0.25 m and a core length of 0.16. The specific electric loading is 23000 ampere conductors/meter. Using the data of this machine, determine the core dimensions, number of stator slots and number of stator conductors for 11 kW, 460 V, 6 pole, 50 Hz motor. Assume a full-load efficiency of 84% and power factor of 0.82 for each machine.the Winding Factor is 0.955.