A jet engine is attached to the wing of an airplane by a security screw (Figure A, marked in black) with a diameter of 40 mm whose purpose is to ensure that if, following a malfunction, the engine exerts too great a horizontal force F on the wing - the screw will break and the engine will detach from the wing, thus the wing will remain intact It is known that the weight of the engine is 3000 kg. A. When the engine exerts a force F of 10 kn, what types of stresses act on the screw? B. When the engine exerts a force F of 10 kn, what is the stress acting on the screw according to the Tarska criterion C. What types of deformations exist in the material when the engine applies a force F of [50] KN d. What is the maximum force F that the motor can apply to a screw without the screw breaking

A jet engine is attached to the wing of an airplane by a security screw (Figure A, marked in black) with a diameter of 40 mm whose purpose is to ensure that if, following a malfunction, the engine exerts too great a horizontal force F on the wing - the screw will break and the engine will detach from the wing, thus the wing will remain intact It is known that the weight of the engine is 3000 kg. A. When the engine exerts a force F of 10 kn, what types of stresses act on the screw? B. When the engine exerts a force F of 10 kn, what is the stress acting on the screw according to the Tarska criterion C. What types of deformations exist in the material when the engine applies a force F of [50] KN d. What is the maximum force F that the motor can apply to a screw without the screw breaking

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter10: Virtual Work And Potential Energy

Section: Chapter Questions

Problem 10.62P: The bar ABC is supported by three identical, ideal springs. Note that the springs are always...

See similar textbooks

Similar questions

Repeat Prob. 4.152 assuming that the 400-kN force is applied at O instead of L.
The homogeneous plate of weight W is supported by a ball-and-socket joint at D and three wires. Draw the FBD of the plate and count the unknowns.
The bar ABC is supported by three identical, ideal springs. Note that the springs are always vertical because the collars to which they are attached are free to slide on the horizontal rail. Find the angle at equilibrium if W = kL. Neglect the weight of the bar.
A jet engine is attached to the wing of an airplane by a security screw (Figure A, marked in black) with a diameter of 40mm whose purpose is to make sure that if, following a malfunction, the engine exerts too great a horizontal force F on the wing - the screw will break and the engine will detach from the wing and thus the wing will remain intact (Figure B).It is known that the weight of the engine is 3000 kg. A. When the engine exerts a force F of size 10[kn] what types of stress act on the screw?B. When the engine exerts a force F of size 10[kn] what is the stress acting on the screw according toTRESCA criterionC. What types of strains are present in the material when the engine exerts a force F of [50] KNd. What is the maximum force F that the engine can apply to a screw without the screw breaking These are the properties of the material the screw is made of:
. The small piston of a hydraulic lift (g. 1) has a cross-sectional area of 3.00cm2, and its large piston has a cross-sectional area of 200cm2. What downward force of magnitude F1 must be applied to the small piston for the lift to raise a load whose weight is Fg = 15.0kN?
a ladder whose length L is 12 m and whose mass m is 45 kg rests against a wall. Its upper end is a distance h of 9.3 m above the ground. The center of gravity of the ladder is one-third of the way up the ladder. A firefighter whose mass M is 72 kg climbs halfway up the ladder. Assume that the wall, but not the ground is frictionless. What forces are exerted on the ladder by the wall and by the ground.
Two Blocks X and Y are in contact on a horizontal frictionless surface. A constant force of 36 N is applied to X as shown in the Figure. The force exerted by X on Y is:
A ball of mass mand radius Rrests at the edge of a step barrier of height has shown in thefigure. There is a horizontal force Tapplied to the ball from its top through a string wrapped around the ball to lift it above the barrier as shown in the figure. What is the minimum tension required to begin to lift the ball off the ground? (g = 9.8 m/s2, m = 1 kg, R = 0.5 m, h = 0.2 m).
A uniform pole of 2.5m length and 4.0kg mass is suspended horizontally fromthe side of a building where it is affixed with a hinge. It is held in place by awire that extends from the unattached end of the pole at an angle of 53 degrees andattached firmly to the wall. A 10.0kg mass is hanging from the end of the poleas well under the influence of gravity.a. Draw a picture of the situation.b. Draw a comprehensive free body diagram showing the force on the wire,the mass, the pole, and both the horizontal and vertical forces on thehinge.c. Use the hinge as the axis of rotation and balance the vertical torques anddetermine the tension in the wire.d. Use inertial dynamics to find the horizontal and vertical forces on thehinge.
A 10 m steel beam of mass 1000 kg extends 4 m beyond the edge of a flat roof. If a 2,000 kg object is placed on the beam 2 m beyond the roof edge and then to balance the beam a load of 750 kg must be placed on roof at _____ from the edge.
A cylindrical liquid storage tank weighing is to be pushed over a change of elevation of 0.25m by a horizontal force F as indicated in the figure. Which of the following gives reaction at A?
A block that has a weight Wa = 100 N is placed on a rough inclined plane, as shown in the figure. Block A is attached to block B by means of a flexible, inextensible cable with a non-compressible mass, which passes through a smooth pulley with a non-compressible mass; for such conditions determine the interval of values of the weight Wb for which the system will remain in equilibrium. Consider mE = 0.25