A jet of water of diameter 50 mm moving with velocity of 40 m/s, strikes a curved fixed symmetrical plate at the centre. Find the force exerted by jet of water in the direction of jet, if jet is deflected through an angle of 120° at outlet of curved plate. V Sin 84 07 V Cos 0 120° Fixed vane V Cos 0 V Sin 0

A jet of water of diameter 50 mm moving with velocity of 40 m/s, strikes a curved fixed symmetrical plate at the centre. Find the force exerted by jet of water in the direction of jet, if jet is deflected through an angle of 120° at outlet of curved plate. V Sin 84 07 V Cos 0 120° Fixed vane V Cos 0 V Sin 0

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A 2.8-in-diameter horizontal water jet having a velocity of 88 ft/s strikes a curved plate, which deflects the water 180° at the same speed. Ignoring the frictional effects, determine the force required to hold the plate against the water stream.
6.36 This two-dimensional water (at 50°F) jet is deflected by the two-dimensional vane, which is moving to the right with a speed of 60 ft/s. The initial jet is 0.30 ft thick (vertical dimension), and its speed is 100 ft/s. What power per foot of the jet (normal to the page) is transmitted to the vane? See §6.5 for useful knowledge about moving CVs.
Find the force exerted by a jet of water of diameter 75 mm on a stationary flat plate, when the jet strikes the plate normally with velocity of 20 m/s.
Water enters vertically and steadily at a rate of 10 L/s into the sprinkler shown. Both water jets have a diameter of 1.2 cm. Disregarding any frictional effects, determine (a) the rotational speed of the sprinkler in rpm and (b) the torque required to prevent the sprinkler from rotating
A jet of water whose diameter is 5cm strikes a fixed cup with a velocity of 9.45m/s and is deflected by 165 degree. The jet leaves with a velocity of 30m/s . if the cup offers a reactive force of 26.5N to the jet when the flow rate was 980 N/min. Determine the ratio of a) Actual to theoretical forces of the jet. b) Velocities at outlet and inlet. Assume any missing data.
For a horizontal water jet having a velocity of 25 m/s strikes a vertical stationary flat plate. The water splatters in all directions in the plane of the plate. How much force is required to hold the plate against the water stream? Assume diameter of pipe is 6 cm
When a pitot tube as shown below is placed in a river with its lower open end facing upstream, water rises in the vertical portion to a height of 50mm above the water surface. Find the flow velocity U. [density of water ρ = 1000kg/m3]
A large lawn sprinkler with two identical arms is used to generate electric power by attaching a generator to its rotating head. Water enters the sprinkler from the base along the axis of rotation at a rate of 5 gal/s and leaves the nozzles in the tangential direction. The sprinkler rotates at a rate of 180 rpm in a horizontal plane. The diameter of each jet is 0.5 in, and the normal distance between the axis of rotation and the center of each nozzle is 2 ft. Determine the maximum possible electrical power produced.
A large lawn sprinkler with two identical arms is used to generate electric power by attaching a generator to its rotating head. Water enters the sprinkler from the base along the axis of rotation at a rate of 5 gal/s and leaves the nozzles in the tangential direction. The sprinkler rotates at a rate of 180 rpm in a horizontal plane. The diameter of each jet is 0.5 in, and the normal distance between the axis of rotation and the center of each nozzle is 2 ft. If the rotating head is somehow stuck, determine the moment acting on the head.
Consider the flow of a fluid at speed v0, through a cylindrical pipe of radius r. What would be the speedof this fluid at a point where, because of a constriction in the pipe, the fluid is confined to a cylindricalopening of radius r/4?
A reducing elbow is used to deflect water flowrate at a rate of 1920 g/s in a horizontal pipe downward by an angle theta = 43 from the flow of direction while accelerating it. The elbow discharges water into the atmosphere. The diameter of the elbow at the inlet is 6.5 cm and at the exit is 1.5cm. The elevation difference between the centers of the exit and the inlet is 22cm . The mass of the elbow and the water is 61.5 kg. Determine the anchoring force needed to hold the elbow in place
A horizontal water jet of constant velocity V impinges normally on a vertical flat plate and splashes off the sides in the vertical plane. The plate is moving toward the oncoming water jet with velocity 1/2V. If a force F is required to maintain the plate stationary, how much force is required to move the plate toward the water jet?