A jet powered airplane, having the following characteristics in steady level flight: rectangular wing , S-20 m2, normal gross mass, m-8986 kg, lift coefficient, CE1.33, parasite drag coefficient, CD-0.02, aspect ratio, AR-7.5 and Oswald efficiency factor, e-0.9, calculate at sea level: 1. Velocity. 2. Thrust and power required.

A jet powered airplane, having the following characteristics in steady level flight: rectangular wing , S-20 m2, normal gross mass, m-8986 kg, lift coefficient, CE1.33, parasite drag coefficient, CD-0.02, aspect ratio, AR-7.5 and Oswald efficiency factor, e-0.9, calculate at sea level: 1. Velocity. 2. Thrust and power required.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Find the minimum engine thrust that is required for a business jet to maintain level flight at standard sea level conditions.weight, W = 20,000 lb; wingspan, b = 54 ft; wing area, S = 320 ft2zero-lift drag coefficient, CD0 = 0.023aerodynamic efficiency factor, e = 0.82Answer: thrust required = ______________ [lbf]
Assume Patm = 10^5, Pa = 14.7 psi ; ρwater ~ 1000 kg/m3 ; ρair ~ 1.2 kg/m3 ; μwater ~ 10^-3 N•s/m2 ; μair ~ 2 x 10^-5 N•s/m2 ; Vwater ~ 10^-6 m2 /s ; Vair ~ 1.67 x 10^-5 m2 /s ; g = 9.8 m/s^2 .; 1 m/s = 2.24 mph ; 1lbf = 4.45 N ; 1 m^3 = 264 gallons The drag data for a Brazuca soccer ball ( take M = 0.5 kg, D = 0.2 m)
A steam generator generates flue gas at an average temperature of 260 C inside a Chimney. The theoretical draft is 0.5 kPa and the ambient condition of the air is 21 C and 100 kPa. Assume the coefficient velocity to be 0.30 and the molecular weight of the flue gas is 32. For air-fuel ratio requirements per second of 15, calculate: a. The diameter of the Chimney, meter b. The theoretical draft, cm H₂O
The wind turbine gives the following data: Blade length, l = 49 m, Wind speed, V= 32 Km/Hr, Air density, ρ = 1.23 kg/m3 , Power Coefficient, Cp = 0.4, Calculate the power available in the rotor in Watts. A- 151931161.80 W B- 394985.47 W C- 60772464.72 W D- 1302564.83 W
An aircraft has the drag polar, C_d=0.015+0.05C_l^2 For a lift coefficient of 0.5, find the value of the drag coefficient and lift drag ratio?
A 0.30 m X 0.40 m branch duct leaves a 0.30 m X 0.60 m main duct at an angle of 60°. The air temperature is 20°C. The dimensions of the main duct remain constant following branch. The flow rate upstream is 2.7 m3/s. Find the pressure downstream in the main duct if at 20°C, the mass per unit volume is 1.2041 kg/m3. Group of answer choices 436 Pa 634 Pa 643 Pa 346 Paplease show full soluton for review and analysis
Air is flowing in a duct with velocity of 7.62 m/s and static pressure of 2.16 cm water gage. The duct diameter is 1.22 m, the barometric pressure 99.4 kPa and the gage flt*d temperature and air temperature are 30 C. What is the total pressure against which the fan will operate in cm of water?
Write the components of Sub-Sonic Wind Tunnel?
Propose a centrifugal pump (brand and model) to transport 10 L/s of a fluid with a density of 1500 kg/m3 from a tank located on the first floor to a reactor on the second floor of the plant (8 meters in height). The reactor's operating pressure is 30 psig; the fluid is at 20 °C, and its viscosity is 15 cp. The pipeline on the pump discharge is 30 meters long (considering accessories are included). Neglect pressure losses in the pump suction. Propose the pipe diameter, schedule 40, commercial steel. Make any necessary assumptions. Select a pump capable of delivering a maximum flow of 15 L/s (remember that normal operation will be at 10 L/s) and discuss the price paid for this condition. Provide a copy of the pump curve indicating the operating point. Also, calculate the power consumption of the pump.
A fan manufacturer rates his fans at 152 mm water gage static pressure for 10 m² of air per second at 21°C, 1,200 rpm and static efficiency of 69%. At what speed, in RPM, would these fans operate to develop 130 mm water gage when the temperature is 316°C?
A ramjet drives a missile at V0=966m/s at an altitude of 33.5km (air density 0.01kg/m3 and T0=232K). If the missile inlet captures a stream tube of air A0=1,1m2 in area, the fuel-to-air ratio is 0,049, and the fuel heating value is 50MJ/kg. what is the fuel mass flow rate?
Hello i have an example with an answer , please show the solution since only the answer was shown in this example. And i need its solution to review properly. Thank you 1.Question : An existing pump is used to pump water with the following data at BEP: D = 2.15 in, N = 1784 rpm, ρ = 998 kg/m3, Q = 18 gpm, H = 4.2 ft. A larger pump is to be designed based from the existing one to be used for pumping slurry (ρ = 1220 kg/m3) such that its best efficiency point occurs as close as possible to a volume flow rate of 48 gpm and at a net head of 15 ft. Calculate the new pump diameter in inches. Round off your final answer to 3 decimal placesAnswer: 2.554