А L B 425 mm C |D 1,000 mm V P A steel bar (1) and an Aluminum bar (2) are connected to a rigid angle ACD. Assuming: • Steel [E = 200 GPa] bar (1) is 6mm x 40mm x 600mm long. • Aluminum [E = 70 GPa] bar (2) is 10mm x 40mm x 600mm long. Poisson's ratio, v = 0.35 • A distance L of 500mm. a)Determine the force P (in kN) required to stretch the Aluminum bar by 1mm. Enter the force, P, into the d21 answer box (in kN, 3 sig digs).

А L B 425 mm C |D 1,000 mm V P A steel bar (1) and an Aluminum bar (2) are connected to a rigid angle ACD. Assuming: • Steel [E = 200 GPa] bar (1) is 6mm x 40mm x 600mm long. • Aluminum [E = 70 GPa] bar (2) is 10mm x 40mm x 600mm long. Poisson's ratio, v = 0.35 • A distance L of 500mm. a)Determine the force P (in kN) required to stretch the Aluminum bar by 1mm. Enter the force, P, into the d21 answer box (in kN, 3 sig digs).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

c. Calculate "P" in KN considering failure on bearing on projected area. Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
A line is recorded as 472.90 m long. It is measured with a0.65 kg tape which is 30.005 m long at 20 °C under a 50N pull supported at both ends. During measurement, thetemperature is 5 °C and the tape is suspended under a 75N pull. The line is measured on 3% grade. E = 200 GPa,cross-sectional area of tape is 3 mm2 and the coefficientof linear expansion is 0.0000116 /°C. Compute:a. The actual length of tape during measurement.b.The total error to be corrected for the inclined distancec.The true horizontal distance
A hollow steel [E = 30,000 ksi] tube (1) with an outside diameter of 3.15 in. and a wall thickness of 0.25 in. is fastened to a solid aluminum [E = 10,000 ksi] rod (2) that has a 2.05 -in. diameter and a solid 1.00 -in. diameter aluminum rod (3). The bar is loaded as shown. Determine the deflection of point D with respect to the fixed support A.
Axial loads are applied to the compound rod that is composed of an aluminum segment rigidly connected between steel and bronze segments. What is the stress in each material given that P = 15 kN? Specify whether tension or compression. Bronze Aluminum Steel A=400 mm? A=600 mm? A= 300 mm? 2P 3P 4P P -3 m + 5 m -4m
A 900 N-m couple is applied to the flywheel in the diagram. The minimum force X required to prevent rotation of the flywheel is also applied. If the coefficient of belt friction is 0.20, a. which tension is larger, TA or TB?Explain b. What is the angle of contact in radians? c. What is the value of the ratio TA/TB?
The cantilever beam consists of a rectangular structural steel tube shape [E = 200 GPa; I = 425 × 106 mm4]. Assume P = 35 kN, w = 10 kN/m, LAB = 1.50 m, and LBC = 2.00 m. Using Appendix C and method of superposition, determine:(a) the beam deflection at point A. [vA = -4.54 mm](b) the beam deflection at point B. [vB = -2.07 mm]
A two pinned end bars AB (Copper), ? = 850 ??2, ? = 120 ??? and BC (Aluminum), ? = 1000??2, ? = 70 ??? is subjected to a horizontal force of 100 ?? applied at pin B as shown in the figure, determine the horizontal displacement of pin B.
The following shaft, having a diameter of 20 mm, is made of steel (Sut = 520 MPa, Se = 260 MPa) and is subjected to a fully reversed transverse force F = 60 N and a fully reversed torque T = 30 N.m. The shaft is fixed at its left end. Find the factor of safety at A for infinite lifetime using the modified Goodman diagram. -100 mm 20-mm D. Select one: O a. Nf = 7.82 O b. Nf = 6.72 O c. Nf = 5.89 %3D O d. Nf = 9.37
d. Calculate "P" in KN considering failure on shear on rivets Two A36 16mm Thick Steel Plates Are Connected By Four Rivets With Fv=152 MPa As Shown. Given: Rivet Dia 20 mm x=100 mm
A circular copper rod having length of P inches is to be twisted by torques 6.5P lb.in until the angle of rotation between the ends of the rod is 3.0°. If the allowable shear strain in the copper is 0.0006 radians, solve for the maximum permissible diameter of the rod? (Where P is 27
A structural steel rod 1(1)/(2) inches in diameter and 25 feet long, in supporting a balcony, carries a tensile load of 29k;E=29 xx10^(3)ksi. a. Find the total elongation delta of the rod. b. What diameter d is necessary if the total delta is limited to 0.1 inch?
A line is recorded as 472.90m long. It is measured with a 0.65kg tape which is 30.005m long at 20C under a 50N pull supported at both ends. During measurement, the temperature is 5C and the tape is measured on 3% grade. E=200GPa. cross sectional area of tape is 3mm and the coefficient of linear expansion is 0.0000116m/"C. A) Compute for sag correction ... Please also indicate how to get the (Pm pull during measurement)