HMS Column ADINT - 400*400 Column BEJOU - 500*600 Column CFKPV - 600*600 Column GLQW - 500*600

Q: roblem Solving (Show the corresponding solution) In a closed traverse ABCDE running anti-clockwise, ...

A:

Q: 20KNE 320KN रूरए 50m²

A: Normal force (P) = 20 KN Area of cross section (A) = 50 m^2 Calculate normal stress. 

Q: A concrete beam of rectangular cross-section of 200 mm x 400 mm is pre-stressed with a force 400 kN ...

A:

Q: 3. The continuous beam shown in the figure is fixed at A and D, and supported along the span by two ...

A:

Q: Reg.no : 5395   Pb # 3: Refer to Figure 2. Assume that friction is negligible, that θ = 115o, and ...

A:

Q: gravity=2.60, SSD Bulk Specific Gravity=2.63, apparent Specific gravity= 2.68, percent absorption=1....

A: Specific gravity generally gives the information regarding the denseness of the aggregates.So,more i...

Q: A contract can be terminated during the construction of a project. There are a variety of reasons fo...

A: To Explain:  Three types of termination of contract which impact the cycle of project and consequenc...

Q: Determine the reaction at the support of the beam/frea, shown in the figure using the Force Method A...

A:

Q: 3. A parabolic cable supports a girder having a weight of 12 KN/m. a) Determine the tension of the c...

A:

Q: A surveyor recorded 50, 52, 53, 51, 51, 53, 52 and 51 paces in walking along a 45 m. Course along a ...

A: According to Given Data  A surveyor recorded 50, 52, 53, 51, 51, 53, 52 and 51 paces walking along a...

Q: 1. Portal Method: The frame shown is subjected to lateral loads as shown. Supports S, T, U V, W and ...

A:

Q: 20KN 20KNE 50m2

A:

Q: The Certified Inspector must reject any wheel rim where the rim or wheel & lock ring are mismatched....

A:   According to the Department of Motor Vehicles (DMV), the regulation relating to wheel or rim and t...

Q: 10 kN/m

A: Given:- w=10kN/m To find:- Maximum moment capacity  

Q: te the flexural stress (MPa) in the concrete for the beam shown using transformed-area 1. Area of 1-...

A:

Q: 5. M 5 m 7 m 5 m 7 m

A:

Q: lid ratio of the sol sample f the soil sample? of the silty sand is 16.85

A:

Q: connects two tangents that intersect the PC which is at station 0 + 168.150 is to be retained and a ...

A: Given:- radius=6 degree curve PC which is at station =0 + 168.150 To find:- PCC  newPT  

Q: From the table below, compute the catchment volume from the total data of precipitation, runoff, gro...

A: Given, Event Jan Feb March April May June July Sept Oct Nov Dec Precipitation 1003 2500 1800 40...

Q: 1. Select the lightest W12 section available to support a dead load of 810 kN and a live load of 1,2...

A: Given, DL=810 KN LL=1235 KN Length of member=6.5 m Diameter of bolt=db=20 mm A572 Grade 55 steel fy=...

Q: A triangular gate having a horizontal base 4 ft. long and an altitude of 6 ft. is inclined 45° from ...

A:

Q: A large soil sample obtained from a borrow pit has a wet mass of 26.50 kg and an in-situ volume of 0...

A:

Q: segments as shown in the figure.

A: Given, Image of an bridge section 

Q: 1. Do you think the government should spend money searching for new resources or on educating the pe...

A: Natural resources are Earth-derived materials that are utilised to sustain life and fulfil human req...

Q: A Channel Cóx13 is used as a tension member. The holes are for 5/8 inch in diameter of bolts. Using ...

A:

Q: Q1. A square footing is located in a dense sand at a depth of 2.80 m. Determine the ultimate bearing...

A: Given:- The depth of the square footing = 2.80 m  The footing size = 2.5 m  The moist unit weight of...

Q: Discuss the primary advantages and disadvantages of bidding for: (a) public work; (b) private work.

A: Tendering Process under development is a course of presenting a proposition to attempt government de...

Q: Magnitude of shrinkage strains depends upon the composition of the concrete.

A: 1. True Magnitude of shrinkage strains depends upon the: composition of the concrete size of membe...

Q: 8. Briefly describe the structure of clay minerals. What is it about these minerals that makes their...

A: Clay minerals are referred to as secondary silicate minerals since they are generated when main sand...

Q: Your construction company plans to be involved in a Design and Build (DB) project. As a project mana...

A: Assuming, as a project manager of the company there are certain stages of the project staging and de...

Q: SEATWORK The figure as shown, ADD the last 2 digits of your i.d. number in the load P. Student i.d. ...

A: Determine load for every P in three case

Q: 1. A vertical rectangular gate is 4 ft. wide and 6 ft. high. Its upper edge is horizontal and on the...

A: Width of gate, b =4ftDepth of gate, d = 6ft

Q: Analyze the given Beam 10KN/m A В 4m 2m 3m Draw Shear and Moment Diagram of the Beam

A:

Q: For the stratified soil shown, the following soil properties are given: , Thickness (m): H= 1.20 H4 ...

A:

Q: 1. What is the stationing of the end of excavation? 2. Find the volume of fill by end area method. 3...

A:

Q: iven the truss below, calculate the forces in each member in kN. Indicate also if the member is ensi...

A: ##Calculation of forces in each member of truss##  

Q: The flow rate for the pipe system is 0.050 m3/s with a total head loss of 12 m. Use C = 120 for all ...

A:

Q: 26. In a specific gravity test, the weight of the dry soil taken is 0.66N. The weight of the pycnome...

A: Appreciate if there is detailed work with explanation for ease of understanding. THANK YOU.

Q: A sample of a dry coarse grained material of 500 grams was shaken through a nest of sieves and the f...

A: Uniformity Coefficient (Cu): It is defined as the ratio of D60 to D10. Cu= D60D10 D60= Particle size...

Q: 80 kN 30 kN D B 8 m G L'om. F 3, Lom -6 m--6 m --6 m

A: To find the force in all the members-

Q: 2. Draw the shear and moment diagram for the given beam shown. Determine the maximum shear and momen...

A:

Q: Based on the geometry calculation of the drawn Mohr circle, what is the minor principal stress (ơ3) ...

A: Step : 1 Mohr’s circle :- It is a 2-D graphical method  for plane stress problems. Mohr’s circle  us...

Q: Estimate the lag time (hr) for the following watershed: Hydraulic length (km) - 3.04 Curve number 60...

A: Given data:Hydraulic length(L)=3.04 km=9973.753 ft.Curve number(CN)=60 Average land slope(S)=1.1%

Q: (a) Design-bid-build is a sequential process to deliver a construction project. Produce a short repo...

A: Step : 1 Design-bid-build :- It is a sequential process to deliver a construction project where one...

Q: 8 kN 4 kN C D 3m 3 m 3 m

A:

Q: AR with BIM in construction

A: GAMMA AR is an app that overlays 3D BIM models on the construction site using augmented reality. It ...

Q: Automobiles A and B shown in below are traveling in adjacent highway lanes and at t = 0 have the pos...

A:

Q: As a student, what are the idea or new knowledge that you will learn when you study about smart fabr...

A: Smart fabrics are fabric structures or fabrics that can detect and respond to mechanical, thermal, c...

Q: Question) Discuss the Plastic hing Lenqth Cep) far this case;- Simply supportedwith two Cancentrated...

A:

Q: Explain three mitigation measures or technologies that can be used to solve the pollution that occur...

A: The introduction of dangerous items into the environment is referred to as pollution. Pollutants can...